微信掃一掃，立即回復！
| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| GB 18145 | 陶瓷片密封水嘴 | Ceramic cartridge faucets |
| GB/T 8375 | 水嘴分類、型號命名方法 | Classification and type nomenclature for taps |
| ANSI/ASAE S436.1 | 裝有噴霧器和噴嘴的中心旋轉軸、彎頭旋轉軸和橫向移動的灌溉機噴水均勻性測定試驗程序 | Test Procedure for Determining the Uniformity of Water Distribution of Center Pivot, Corner Pivot, and Moving Lateral Irrigation Machines Equipped with Spray or Sprinkler Nozzles |
| ANSI/ASME MFC-3M-1 | 用孔板、噴嘴和文杜利流量計測量管道中液體流量.第1部分:總則 | Measurement of fluid Flow in Pipes Using Orifice, Nozzle, and Venturi-Part 1-General |
| ANSI/ASME MFC-3M-2 | 用孔板、噴嘴和文杜利流量計測量管道中液體流量.第2部分:孔板 | Measurement of fluid Flow in Pipes Using Orifice, Nozzle, and Venturi-Part 2-Orifice Plates |
| ANSI/ASME MFC-3M-3 | 用孔板、噴嘴和文杜利流量計測量管道中液體流量.第3部分:噴嘴和文杜利噴嘴 | Measurement of Fluid Flow in Pipes Using Orifice, Nozzle, and Venturi-Part 3 - Nozzles and Venturi Nozzles |
| ANSI/ASME MFC-3M-4 | 用孔板、噴嘴和文杜利流量計測量管道中液體流量.第4部分:文杜利流量計 | Measurement of Fluid Flow in Pipes Using Orifice, Nozzle, and Venturi - Part 4 - Venturi Meters |
| ANSI/ASME MFC-7M | 利用臨界文氏流量噴嘴測量氣體流量 | Gas Flow by Means of Critical Flow Venturi Nozzles, Measurement of |
| ANSI/ASTM F1601 | 中央真空吸塵系統家用電動管嘴馬達壽命評估試驗方法 | Test Method for Motor Life Evaluation of a Household Electric Motorized Nozzle for Central Vacuum Cleaning System |
| ANSI/ASTM F1692 | 家庭中央真空吸塵系統渦輪動力噴嘴壽命評估試驗方法 | Test Method for Life Evaluation of aTurbine Powered Nozzle for Household Central Vacuum Cleaning Systems |
| ANSI/AWS C4.5M | 氧化燃料噴嘴的統一命名系統 | Uniform Designation System for Oxyfuel Nozzles |
| ANSI/AWWA C708 | 多噴嘴式冷水表 | Cold-Water Meters - Multijet Type |
| ANSI/HI 9.6.2 | 離心泵和立式泵.最大噴嘴負荷 | Centrifugal and Vertical Pumps for Allowable Nozzle Loads |
| ANSI/NFPA 1962 | 消防水龍帶包括接頭和噴嘴的保養、使用和維修試驗 | Care, Use, and Service Testing of Fire Hose, Including Couplings and Nozzles |
| ANSI/NFPA 1964 | 噴嘴(關閉閥和端頭) | Spray Nozzles (Shutoff and Tip) |
| ANSI/UL 2167 | 消防設備用水霧噴嘴的安全標準 | Standard for Safety for Water Mist Nozzles for Fire-Protection Service |
| ANSI/UL 2351 | 防火用噴嘴的安全標準 | Standard for Safety for Spray Nozzles for Fire-Protection Service |
| ANSI/UL 401 | 防火服務用便攜式噴霧軟管噴嘴的安全標準 | Standard for Safety for Portable Spray Hose Nozzles for Fire-Protection Service (bulletin dated February 16, 2004) |
| ASME MFC-7M | 用極限流量文氏噴嘴測量氣體流量 | (Measurement of gas flow by means of critical flow Venturi nozzles) |
| ASTM C 605 | 耐火粘土制噴嘴和套管的二次加熱變化的試驗方法 | Test Method for Reheat Change of Fireclay Nozzles and Sleeves |
| ASTM E 641 | 農用液壓噴嘴的試驗的標準方法 | Standard Methods for Testing Hydraulic Spray Nozzles Used in Agriculture |
| ASTM F 1413 | 漏油分散設備:起重臂和噴油嘴系統 | Oil Spill Dispersant Application Equipment: Boom and Nozzle Systems |
| ASTM F 1460 | 溢油分散劑噴灑設備噴桿和噴嘴系統校準的標準規范 | Standard Practice for Calibrating Oil Spill Dispersant Application Equipment Boom and Nozzle Systems |
| BS 1486-1 | 潤滑脂管嘴.第1部分:機械與車輛用潤滑脂管嘴和適配器 | Lubricating nipples - Lubricating nipples and adaptors for use on machinery and vehicles |
| BS 1486-2 | 潤滑脂管嘴.重型潤滑脂管嘴 | Lubricating nipples - Heavy duty lubricating nipples |
| BS 1486-4 | 潤滑脂管嘴規范.第4部分:液壓潤滑脂管嘴規范 | Lubricating nipples - Specification for hydraulic grease nipples |
| BS 2C 13 | 飛機重力灌注燃油口及相關供燃油嘴的尺寸規范(米制系列) | Specification for sizes of aircraft gravity filling orifices and associated replenishment nozzles (metric series) |
| BS 5041-1 | 消防栓系統設備.第1部分:濕式水嘴接地閥規范 | Fire hydrant systems equipment - Specification for landing valves for wet risers |
| BS 5041-2 | 消防栓系統設備.第2部分:干式水嘴接地閥規范 | Fire hydrant systems equipment - Specification for landing valves for dry risers |
| BS 5041-4 | 消防栓系統設備.第4部分:干式水嘴用接地閥箱規范 | Fire hydrant systems equipment - Specification for boxes for landing valves for dry risers |
| BS 5041-5 | 消防栓系統設備.第5部分:泡沫入口及干式水嘴用箱規范 | Fire hydrant systems equipment - Specification for boxes for foam inlets and dry riser inlets |
| BS 6356-1 | 農作物防護用噴霧設備.第1部分:噴嘴試驗方法 | Spraying equipment for crop protection - Method of test for sprayer nozzles |
| BS 6356-13 | 農作物保護噴霧設備.第13部分:氣動噴霧器:噴嘴旋軸螺母尺寸 | Spraying equipment for crop protection - Air-assisted sprayers - Dimensions of nozzle swivel nuts |
| BS 6356-2 | 農作物防護用噴霧設備.第2部分:噴嘴與壓力計連接尺寸規范 | Spraying equipment for crop protection - Specification for connecting dimensions for nozzles and manometers |
| BS 6356-4 | 農作物保護用噴霧設備.第4部分:田間噴嘴性能極限規范 | Spraying equipment for crop protection - Specification for performance limits for field spraying nozzles |
| BS 6356-6 | 農作物保護用噴霧設備.第6部分:帶插接固定裝置噴嘴連接尺寸規范 | Spraying equipment for crop protection - Specification for connecting dimensions for nozzles with bayonet fixing |
| BS 6913-13 | 運土機械的操作和維修.潤滑油配件規范.油嘴類型 | Operation and maintenance of earth-moving machinery - Specification for lubrication fittings - Nipple type |
| BS 6913-14 | 運土機械的操作和維修.潤滑油配件規范.注油搶噴嘴 | Operation and maintenance of earth-moving machinery - Specification for lubrication fittings - Grease-gun nozzles |
| BS EN 12067-1 | 燃?xì)鈬娮旌腿細庋b置用燃?xì)?空氣混合調節器.第1部分:氣動結構類型 | Gas/air ratio controls for gas burners and gas burning appliances - Pneumatic types |
| BS EN 12094-7 | 固定消防系統.氣體滅火系統元件.CO2系統用噴嘴的要求和試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for nozzles for CO2 systems |
| BS EN 13079 | 防飲用水回流造成污染的設備.有噴嘴的氣隙.A類.D型 | Devices to prevent pollution by backflow of potable water - Air gap with injector - Family A. Type D |
| BS EN 13760 | 輕型和重型車輛用機動車液化石油氣填充系統.噴油嘴試驗要求和尺寸 | Automotive LPG filling system for light and heavy duty vehicles - Nozzle, test requirements and dimensions |
| BS EN 293 | 油壓力霧化噴嘴.最低要求.試驗 | Specification for oil pressure atomizing nozzles - Minimum requirements - Testing |
| BS EN 299 | 油壓霧化噴嘴.角度和噴射特性的測定 | Oil pressure atomizing nozzles - Determination of the angle and spray characteristics |
| BS EN 303-6 | 供暖鍋爐.帶強制通風燃燒嘴器的供暖鍋爐.標稱熱輸入量不超過70kw的用霧化油燃燒爐的組合式鍋爐的家用熱水供 | Heating boilers - Heating boilers with forced draught burners - Specific requirements for the domestic hot water operation of combination boilers with atomizing oil burners of nominal heat input not exceeding 70 kW |
| BS EN 303-6 | 供暖鍋爐.帶強制通風燃燒嘴器的供暖鍋爐.標稱熱輸入量不超過70kw的用霧化油燃燒爐的組合式鍋爐的家用熱水供 | Heating boilers - Heating boilers with forced draught burners - Specific requirements for the domestic hot water operation of combination boilers with atomizing oil burners of nominal heat input not exceeding 70 kW |
| BS EN 625 | 裝有常壓送風噴嘴的燃?xì)饧泄┡仩t.公稱熱輸入量不超過70kW的混合鍋爐的家庭熱水供暖的具體要求 | Gas-fired central heating boilers - Specific requirements for the domestic hot water operation of combination boilers of nominal heat input not exceeding 70 kW |
| BS EN ISO 11545 | 農業灌溉設備.有噴嘴或噴霧咀的橫向移動排灌機械和中心軸.水分配均勻性的測定 | Agricultural irrigation equipment - Centre-pivot and moving lateral irrigation machines with sprayer or sprinkler nozzles - Determination of uniformity of water distribution |
| BS EN ISO 15029-1 | 石油和相關產品.耐火液體噴射點燃特性的測定.噴射火焰持久性.空心錐形噴嘴法 | Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Spray flame persistence - Hollow-cone nozzle method |
| BS EN ISO 20844 | 石油和相關產品.使用柴油注射器噴嘴測定含聚合物油的剪切穩定性 | Petroleum and related products - Determination of the shear stability of polymer-containing oils using a diesel injector nozzle |
| BS EN ISO 5167-3 | 用插入圓截面管道中的壓差裝置測量流體流量.噴嘴和文杜利噴嘴 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Nozzles and Venturi nozzles |
| BS EN ISO 9300 | 用臨界流量文丘里噴嘴測定氣體流量 | Measurement of gas flow by means of critical flow Venturi nozzles |
| BS G 175 | 航空用燃油嘴接地插頭和插座 | Aircraft fuel nozzle grounding plugs and sockets |
| BS ISO 14681 | 柴油發動機.燃料噴射泵試驗.燃料噴嘴的校準 | Diesel engines - Fuel injection pump testing - Calibrating fuel injectors |
| BS ISO 2697 | 柴油發動機.燃料噴嘴."S"尺寸 | Diesel engines - Fuel nozzles - Size "S" |
| BS ISO 4010 | 柴油發動機.針?biāo)ㄐ蜏笮?zhǔn)噴嘴 | Diesel engines - Calibrating nozzle, delay pintle type |
| BS ISO 7026 | 柴油發動機.S1規格B型針?biāo)ㄊ絿娮斓?0、21、21.1和27型擰入式噴嘴固定器 | Diesel engines - Screw-in injection nozzle holders, types 20, 21, 21.1 and 27 for pintle nozzle size 'S1' type 'B' |
| BS ISO 9102 | 柴油發動機.24、25、26和26.1型擰入式噴嘴底座 | Diesel engines - Screw-in injection nozzle holders types 24, 25, 26 and 26.1 |
| BS ISO TR 15377 | 用壓差裝置測量流體流量.ISO 5167-1規定范圍之外的噴嘴和節流孔板規范指南 | Measurement of fluid flow by means of pressure differential devices - Guidelines for specification of nozzles and orifice plates beyond the scope of ISO 5167-1 |
| DD ENV 1259-1 | 燃?xì)馐絾螄娮煅b于頂部的幅射管加熱器和非家用燃?xì)馐窖b于頂部的發光幅射加熱器.制定合理使用能源的要求和試 | Single burner gas fired overhead radiant tube heaters and non-domestic gas-fired overhead luminous radiant heaters. Requirements and test methods for establishing the rational use of energy. Radiometric method A |
| DD ENV 1259-2 | 燃?xì)馐絾螄娮煅b于頂部的幅射管加熱器和非家用燃?xì)馐窖b于頂部的發光幅射加熱器.建立合理使用能源的要求和試 | Single burner gas fired overhead radiant tube heaters and non-domestic gas-fired overhead luminous radiant heaters. Requirements and test methods for establishing the rational use of energy. Radiometric method B |
| DD ENV 1259-3 | 燃?xì)馐絾螄娮煅b于頂部的輻射管加熱器和非家用燃?xì)馐窖b于頂部的發光輻射加熱器.建立合理使用能源的要求和試 | Single burner gas fired overhead radiant tube heaters and non-domestic gas-fired overhead luminous radiant heaters. Requirements and test methods for establishing the rational use of energy. Radiometric method C |
| DIN 11210 | 農業機械.帶式噴霧器.噴嘴支架的連接尺寸 | Agricultural machinery; band sprayer; connection dimensions for nozzleholders |
| DIN 11215 | 農業機械.農作物保護噴霧器.噴嘴的連接尺寸 | Agricultural machinery; sprayers for crop protection, connection dimensions for nozzles |
| DIN 12898 | 實驗室用水管龍頭.出水嘴 | Laboratory taps; outlet nozzles |
| DIN 14200 | 噴嘴排放 | Nozzle discharge |
| DIN 14494 | 開式噴嘴固定式噴水系統 | Water spray systems, fixed, with open nozzles |
| DIN 16966-4 | 玻璃纖維增強聚酯樹脂管(UP-GF)管件和接頭.三通噴管嘴尺寸 | Glass fibre reinforced polyester resin (UP-GF) pipe fittings an joints; Tees, Nozzles, Dimensions |
| DIN 20033 | 軟管連接件.帶壓緊螺母的錐形管嘴 | Hose fittings; tapered nozzle with clamping nut |
| DIN 20035 | 軟管管接頭.法蘭管嘴.公稱壓力16 | Hose fittings; flange nozzle; nominal pressure 16 |
| DIN 20038 | 軟管管接頭.接頭管嘴 | Hose fittings; coupling nozzles |
| DIN 24375 | 表面處理.無氣噴槍的扁形噴嘴.尺寸、測試、標記 | Surface treatment; flat-stream nozzles for airless spray guns; dimensions, testing, marking |
| DIN 25480-1 | 污染防護箱用元件.噴嘴、遠距離操作鉗用環.窗和支柱系統 | Components for contamination protection boxes; nozzles, rings for remote handling tongs, windows and posting systems |
| DIN 28025 | 不銹鋼噴嘴.PN 10 至 PN 40 | Nozzles of stainless steel - PN 10 to PN 40 |
| DIN 28115 | 碳鋼噴嘴.PN 10 至 PN 40 | Carbon steel nozzles - PN 10 to PN 40 |
| DIN 28136-11 | 攪拌器.第11部分:玻璃纖維襯里的 CE 型公稱容量為 4000 升更換用剛制攪拌器頂蓋噴嘴的位置和尺寸 | Agitator vessels; position and sizes of cover nozzles for glass lined steel agitator vessels, type CE, with a nominal volume of 4000 litres for replacement purposes |
| DIN 28136-14 | 攪拌容器.第14部分:BE型d1=2400-3600mm的搪玻璃鋼攪拌容器用蓋噴嘴的位置和大小, CE型d1=2400-3600mm的搪 | Agitator vessels - Part 14: Position and sizes of cover nozzles for glass lined steel agitator vessels, position H for vessels form BE with d<(Index)1> = 2400 mm to 3600 mm and position K for vessels form CE with d<(Index)1> = 2400 mm to 3600 mm; inactive for new design |
| DIN 28136-2 | 攪拌容器.第2部分:非合金和不銹鋼容器頂蓋噴嘴的位置和尺寸 | Agitator vessels - Part 2: Positions and sizes of cover nozzles in non-alloy and stainless steel vessels |
| DIN 28136-3 | 攪拌容器.第3部分:搪玻璃鋼件攪拌容器頂蓋噴嘴的位置和尺寸 | Agitator vessels - Part 3: Position and sizes of cover nozzles for glass lined steel agitator vessels |
| DIN 28139-3 | 搪瓷容器的焊接凸肩.分離式搭接法蘭連接用S形接管嘴.連接尺寸 | Welding necks for glass lined vessels; form S nozzles for lapped divided flange connections; connecting dimensions |
| DIN 28151 | 鋼制搪玻璃攪拌容器用套管噴嘴.噴嘴位置 | Nozzles of jacket on agitated vessels, of glass lined steel - Position of nozzles |
| DIN 29736-2 | 航空航天.燃料噴嘴接地插頭和插座.技術規范 | Aerospace; fuel nozzle grounding plugs and sockets; technical specification |
| DIN 3404 | 扁平注油嘴 | Lubricating nipples; button head |
| DIN 3405 | 杯形潤滑油嘴 | Lubricating nipples cupped type |
| DIN 3410 | 潤滑油排出管嘴.總尺寸和裝配尺寸 | Lubricating nipples; overall and fitting dimensions |
| DIN 3528 | 煤氣裝置用閥門.帶密封墊的噴嘴 | Valves for gas installations; nozzles with gasket |
| DIN 45635-25 | 機器排放的空氣傳播噪聲的測量.第25部分:包洛面法.氣焊及等離子焊噴嘴和機器 | Measurement of airborne noise emitted by machines; enveloping surface method, oxy-fuel gas and plasma torches and machines |
| DIN 4661-4 | 壓縮氣瓶.第4部分:焊接鋼氣瓶噴嘴 | Gas cylinders, welded steel gas cylinders; nozzles |
| DIN 5042-7 | 燃?xì)鉄艉兔簹鉄?第7部分:固定噴嘴 | Combustion lamps and gas luminaires; fixed nozzles |
| DIN 5059-1 | 包裝.金屬和塑料管.金屬管.管嘴、管肩 | Packaging; metal and plastic tubes; metal tubes; tube nozzles, tube shoulders |
| DIN 5059-2 | 包裝.金屬和塑料管.塑料管.管嘴 | Packaging; metal and plastic tubes; plastic tubes; tube nozzles |
| DIN 71412 | 錐形潤滑劑注油嘴 | Lubricating nipples; cone type |
| DIN 73372 | 規格T and U 噴油嘴 | Fuel injection nozzles, size T and U |
| DIN 7584 | 家用安裝水管配件.壓力為10巴的平密封墊帶外螺紋的鋼管接管嘴 | Water-fittings for house installation; steal tube nozzles with external thread, flat sealing up to working pressure of 10 bar |
| DIN 7588 | 家裝設備用水管配件.平密封螺旋接頭.壓力10巴的一端帶內螺紋,另一端帶鋼管噴嘴、銅管噴嘴或套管 | Water-fittings for house installation; boltings with flat seal; one side threaded coupling with inside-thread, on the other side steel tube nozzle, copper tube nozzle or sleeve PN 10 |
| DIN 7589 | 家裝設備用水管配件.平密封螺旋接頭.壓力10巴的一端帶外螺紋,另一端帶鋼管噴嘴、銅管噴嘴和套管 | Water-fittings for house installation; boltings with flat seal; one side threaded coupling with outside-thread, on the other side steel tube nozzle, copper tube nozzle or sleeve PN 10 |
| DIN 7592 | 家用安裝水管配件.標稱工作壓力為10巴以下的銅管管嘴 | Water-fittings for house installation; copper tube nozzles up to working pressure of 10 bar |
| DIN 8535 | 氣動工具.螺紋管嘴 | Pneumatic tools, screw nozzle tips |
| DIN 8536 | 氣動工具.轉接管嘴 | Pneumatic tools; transition nozzle tips |
| DIN 8537 | 氣動工具.錐形噴氣管嘴、連接螺母、連接管 | Pneumatic tools; cone nozzle tips, connection nuts, connection nipples |
| DIN EN 12094-7 | 固定式消防系統.氣體滅火系統用元件.第7部分:CO2系統用噴嘴的要求和試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 7: Requirements and test methods for nozzles for CO<(Index)2> systems; German version EN 12094-7:2000 + A1:2005 |
| DIN EN 13079 | 防飲用水回流污染的裝置.有噴嘴的氣隙.A系列D型 | Devices to prevent pollution by backflow of potable water - Air gap with injector - Family A; Type D; German version EN 13079:2003 |
| DIN EN 13760 | 輕型和重型車輛用汽車液化石油氣灌充設備.噴嘴的試驗要求和尺寸 | Automotive LPG filling system for light and heavy duty vehicles - Nozzle, test requirements and dimensions; German version EN 13760:2003 |
| DIN EN 14979 | 包裝.軟塑料/金屬層壓管.S13噴嘴的尺寸和公差 | Packaging - Flexible plastic/metal laminate tubes - Dimensions and tolerances of nozzle S 13; German version EN 14979:2006 |
| DIN EN 293 | 油壓噴霧器噴嘴.最低要求.試驗 | Oil pressure atomizing nozzles; minimum requirements, testing; german version EN 293:1992 |
| DIN EN ISO 5167-3 | 用插入圓截面管道中的壓差裝置測量流體流量.第3部分:噴嘴和文杜利噴嘴 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2003); German version EN ISO 5167-3:2003 |
| DIN EN ISO 9300 | 用文杜利臨界流量噴嘴測量氣體流量 | Measurement of gas flow by means of critical flow Venturi nozzles (ISO 9300:2005); German version EN ISO 9300:2005 |
| DIN ISO 14710 | 農用機械和拖拉機.作物保護設備.空氣輔助的噴灑器.噴嘴旋轉螺母的尺寸 | Agricultural machinery and tractors - Equipment for crop protection - Air-assisted sprayers; dimensions of nozzle swivel-nuts (ISO 14710:1996) |
| DIN ISO 2698 | 柴油發動機.夾緊式燃油噴嘴.7 型和 28 型; 等同采用 ISO 2698:1993 | Diesel engines - Clamp-mounted fuel injectors, types 7 and 28; identical with ISO 2698:1993 |
| DIN ISO 4010 | 道路車輛.延遲針閥式標定噴嘴 | Calibrating Nozzle, Delay Pintle Type |
| DIN ISO 413 | 航空航天.潤滑油加油管嘴頭 | Aircraft; heads of lubricating nipples; identical with ISO 413, edition 1974 |
| DIN ISO 5682-1 | 農用機械和拖拉機.農作物防護設備.第1部分:噴灑器噴嘴的試驗方法 | Agricultural machinery and tractors - Equipment for crop protection - Part 1: Test methods for sprayer nozzles (ISO 5682-1:1996) |
| DIN ISO 7026 | 道路車輛.B類S規格的針式噴嘴用的20、21和27型螺絲擰入式噴嘴架 | Road vehicles; screw-in injection nozzle holders types 20, 21 and 27 for pintle nozzle size "S", type "B"; identical with ISO 7026:1990 |
| DIN ISO 7030 | 道路車輛.12，13，14，15，16，17，18 和19 型 螺旋擰入式噴嘴固定架 | Road vehicles; screw-mounted injection nozzle holders, types 12, 13, 14, 15, 16, 17, 18 and 19; identical with ISO 7030:1987 |
| DIN ISO 8356 | 道路車輛.柴油發動機.22型螺旋擰入式噴油嘴 | Road vehicles; diesel engines; screw-in injector; type 22; identical with ISO 8356, edition 1984 |
| DIN ISO 9102 | 道路車輛.壓燃式發動機.24.25.26型螺絲擰入式噴嘴座 | Road vehicles; compression-ignition engines; screw-in injection nozzle holders, types 24, 25 and 26; Identical with ISO 9102:1990 |
| DIN ISO 9158 | 道路車輛.無鉛汽油用管嘴 | Road vehicles; nozzle spouts for unleaded gasoline; identical with ISO 9158:1988 |
| DIN ISO 9159 | 道路車輛.含鉛汽油和柴油用管嘴 | Road vehicles; nozzle spouts for leaded gasoline and diesel fuel; identical with ISO 9159:1988 |
| DIN V ENV 1259-2 | 單噴嘴燃?xì)忭敳枯椛涔芗訜崞骱蜕逃萌細忭敳堪l(fā)光輻射加熱器.第2部分:確定合理能耗的要求及試驗方法.輻射計法 | Single burner gas-fired overhead radiant tube heaters and non-domestic gas-fired overhead luminous radiant heaters - Part 2: Requirements and test methods for establishing the rational use of energy; radiometric method B; German version ENV 1259-2:1996 |
| DIN V ENV 1259-3 | 單噴嘴燃?xì)忭敳枯椛涔芗訜崞骱蜕逃萌細忭敳堪l(fā)光輻射加熱器.第3部分:確定合理能耗的要求及試驗方法.輻射計法 | Single burner gas-fired overhead radiant tube heaters and non-domestic gas-fired overhead luminous radiant heaters - Part 3: Requirements and test methods for establishing the rational use of energy; radiometric method C; German version ENV 1259-3:1996 |
| EN 12067-1-1998+A1 | 燃?xì)鈬娮旌腿細庋b置用燃?xì)?空氣混合調節器 第1部分：氣動型 | Gas/air ratio controls for gas burners and gas burning appliances - Part 1: Pneumatic types |
| EN 12094-7 | 固定式消防系統 氣體滅火系統的部件 第7部分：對CO2系統的噴嘴的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 7: Requirements and test methods for nozzles for CO<(Index)2> systems |
| EN 13012 | 加油站 加油機上使用的自動噴嘴的結構和性能 | Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers |
| EN 13760 | 輕型和重型機動車輛用液化石油氣填充系統 噴油嘴試驗要求和尺寸 | Automative LPG filing system for light and heavy duty vehicles - Nozzle, test requirements and dimensions |
| EN 293 | 油壓噴霧噴嘴 最低要求 測試 | Oil pressure atomizing nozzles; minimum requirements; testing |
| EN 299 | 油壓噴霧噴嘴 角度和噴霧特性的測定 | Oil pressure atomizing nozzles - Determination of the angle and spray characteristics |
| EN ISO 11545 | 農業排灌設備 有噴嘴和噴霧嘴的橫向移動排灌機械和中心軸 分配水的均勻性的測定 | Agricultural irrigation equipment - Centre-pivot and moving lateral irrigation machines with sprayer or sprinkler nozzles - Determination of uniformity of water distribution (ISO 11545:2001) |
| EN ISO 15029-1 | 石油和相關產品 難燃液體噴射燃燒特性的測定 第1部分：噴流燃燒持久度 空錐噴嘴法 | Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Part 1: Spray flame persistence - Hollow-cone nozzle method (ISO 15029-1:1999) |
| EN ISO 5167-1 | 用壓差裝置測量流體流量 第1部分：圓截面管道中插入的節流孔板、噴嘴和文杜利管 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| EN ISO 5167-3 | 圓截面管道中用壓差裝置測量流體流量 第3部分：噴嘴和文杜利噴嘴 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2003) |
| EN ISO 9300 | 用文杜利臨界流量噴嘴測定氣體流量 | Measurement of gas flow means of critical flow Venturi nozzles (ISO 9300:1990) |
| GB 796 | 鹵代烷滅火系統噴嘴性能要求和試驗方法 | Halon fire extinguishing systems--Performance requirements and method of test for nozzles |
| GB/T 19230.3 | 評價汽油清凈劑使用效果的試驗方法第3部分: 汽油清凈劑對電子孔式燃油噴嘴(PFI)堵塞傾向影響的試驗方法 | Test method for evaluating gasoline detergent in use--Part 3: Test method for evaluating gasoline detergent produced effect forelectronic port fuel injector(PFI) fouling |
| GB/T 2624.3 | 用安裝在圓形截面管道中的差壓裝置測量滿管流體流量 第3部分：噴嘴和文丘里噴嘴 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles |
| GB/T 5772 | 柴油機噴油嘴偶件技術條件 | Technical specification for fuel injection nozzles of diesel engines |
| HG/T 3144 | 小容量內混式蒸汽霧化輕質油燒嘴 | () |
| HG/T 3144 | 小容量內混式蒸汽霧化輕質油燒嘴 | () |
| HG/T 3168 | 油噴嘴性能試驗方法 | () |
| ISO 10626 | 作物保護設備 噴霧器 卡口安裝的噴嘴連接尺寸 | Equipment for crop protection; sprayers; connecting dimensions for nozzles with bayonet fixing |
| ISO 11545 | 農業排灌設備 有噴嘴和噴霧嘴的橫向移動排灌機械和中心軸 分配水的均勻性的測定 | Agricultural irrigation equipment - Centre-pivot and moving lateral irrigation machines with sprayer or sprinkler nozzles - Determination of uniformity of water distribution |
| ISO 14710 | 作物保護設備 空氣引射噴霧器 噴嘴旋轉螺母的尺寸 | Equipment for crop protection - Air-assisted sprayers - Dimensions of nozzle swivel nuts |
| ISO 15029-1 | 石油和相關產品 難燃液體噴射燃燒特性的測定 第1部分:噴流燃燒持久度 空錐噴嘴法 | Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Part 1: Spray flame persistence - Hollow-cone nozzle method |
| ISO 20844 | 石油和相關產品.用柴油噴射器噴嘴測定含高聚物油的剪切穩定性 | Petroleum and related products - Determination of the shear stability of polymer-containing oils using a diesel injector nozzle |
| ISO 2699 | 柴油機 法蘭安裝式“S”號噴油嘴 2、3、4、5和6型 | Diesel engines; flange-mounted fuel injectors, size "S"; types 2, 3, 4, 5 and 6 |
| ISO 413 | 航空器 潤滑油加油管嘴的頭部 | Aircraft; Heads of lubricating nipples |
| ISO 46 | 航空器 燃油管嘴接地插頭和插座 | Aircraft; Fuel nozzle grounding plugs and sockets |
| ISO 5167-1 Technical Corrigendum 1 | 用壓差裝置測量流體流量 第1部分:圓截面管道中插入的節流孔板、噴嘴和文杜利管 技術勘誤1 | Measurement of fluid flow by means of pressure differential devices - Part 1: Orifice plates, nozzles and Venturi tubes inserted in circular cross-section conduits running full - Technical Corrigendum 1 |
| ISO 5167-3 | 用插入圓截面管道中的壓差裝置測量流體流量.第3部分:噴嘴和文杜利噴嘴 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles |
| ISO 5176-1 | 用壓差裝置測量流體流量.第1部分:圓截面管道中插入的節流孔板、噴嘴和文杜利管 | Measurement of fluid flow by means of pressure differential devices; part 1: orifice plates, nozzles and Venturi tubes inserted in circular cross-section conduits running full |
| ISO 5682-1 | 作物保護設備 噴霧設備 第1部分:噴霧機噴嘴的試驗方法 | Equipment for crop protection - Spraying equipment - Part 1: Test methods for sprayer nozzles |
| ISO 6182-9 | 消防.自動噴水滅火系統.第9部分:水霧噴嘴的要求和試驗方法 | Fire protection - Automatic sprinkler system - Part 9: Requirements and test methods for water mist nozzles |
| ISO 6392-2 | 土方機械 潤滑件 第2部分:黃油槍噴嘴 | Earth-moving machinery - Lubrication fittings - Part 2: Grease-gun nozzles |
| ISO 7026 | 柴油機 S尺寸軸針式噴油嘴偶件B型擰入式噴嘴器件(20、21、21.1和27型) | Diesel engines - Screw-in injection nozzle holders, types 20, 21, 21.1 and 27 for pintle nozzle size "S", type "B" |
| ISO 7026 | 柴油機 S尺寸軸針式噴油嘴偶件B型擰入式噴嘴器件(20、21、21.1和27型) | Diesel engines - Screw-in injection nozzle holders, types 20, 21, 21.1 and 27 for pintle nozzle size "S", type "B" |
| ISO 7030 | 道路車輛 12、13、14、15、16、17、18和19型螺旋擰入式噴嘴器件 | Road vehicles; Screw-mounted injection nozzle holders, types 12, 13, 14, 15, 16, 17, 18 and 19 |
| ISO 7824 | 造船及海上結構物 潤滑油嘴 錐型及平肩型 | Shipbuilding and marine structures; Lubrication nipples; Cone and flat types |
| ISO 8169 | 作物保護設備 噴霧器 噴嘴和壓力計的連接尺寸 | Equipment for crop protection; Sprayers; Connecting dimensions for nozzles and manometers |
| ISO 9158 | 道路車輛 無鉛汽油用管嘴 | Road vehicles; nozzle spouts for unleaded gasoline |
| ISO 9159 | 道路車輛 含鉛汽油和柴油用管嘴 | Road vehicles; nozzle spouts for leaded gasoline and diesel fuel |
| ISO 9300 | 用臨界流量文丘里噴嘴測定氣體流量 | Measurement of gas flow by means of critical flow Venturi nozzles |
| ISO/TR 15377 Technical Corrigendum 1 | 用壓差裝置測量流體流量 符合ISO 5167-1規定的噴嘴和節流孔板規范指南 技術勘誤1 | Measurement of fluid flow by means of pressure-differential devices - Guidelines for the specification of nozzles and orifice plates beyond the scope of ISO 5167-1; Technical Corrigendum 1 |
| ISO/TR 15377 | 用壓差裝置測量流體流量 符合ISO 5167-1規定的噴嘴和節流孔板規范指南 | Measurement of fluid flow by means of pressure-differential devices - Guidelines for specification of nozzles and orifice plates beyond the scope of ISO 5167-1 |
| JB/T 10645 | 碳化硅特種制品 氮化硅結合碳化硅 燒嘴套 | Special products of silicon carbide-Silicon nitride bonded silicon carbide-Nozzle tubes |
| JB/T 10645 | 碳化硅特種制品 氮化硅結合碳化硅 燒嘴套 | Special products of silicon carbide-Silicon nitride bonded silicon carbide-Nozzle tubes |
| JB/T 10697 | 碳化硅特種制品 反應燒結碳化硅 燒嘴套 | () |
| JB/T 10697 | 碳化硅特種制品 反應燒結碳化硅 燒嘴套 | () |
| JB/T 51184 | 噴油嘴偶件可靠性考核 評定方法、臺架試驗方法及失效判定 | () |
| JB/T 5174 | 噴油嘴偶件 型式及連接尺寸 | () |
| JB/T 7296 | 柴油機噴油嘴偶件 技術條件 | () |
| JB/T 7297 | 柴油機噴油嘴偶件 性能試驗方法 | () |
| JB/T 7661 | 柴油機油泵油嘴產品清潔度 限值及測定方法 | () |
| JB/T 8604 | 氣動小噴嘴式內徑測量裝置 | () |
| JB/T 8650.4 | 機床冷卻系統輔件 噴嘴 | () |
| JB/T 9729 | 柴油機噴油泵柱塞偶件、出油閥偶件、噴油嘴偶件徑部密封值樣品 技術條件 | () |
| JB/T 9730 | 柴油機噴油嘴偶件、噴油泵柱塞偶件、噴油泵出油閥偶件 金相檢驗 | () |
| JB/T 9732 | 軸針式標準噴油嘴偶件 | () |
| JB/T 9736 | 噴油嘴偶件、柱塞偶件、出油閥偶件 磁粉探傷方法 | () |
| JC/T 1043 | 水嘴鉛析出限量 | Limit of lead extraction in faucets |
| JIS B1575 | 油脂槍噴嘴 グリースニップル | Grease nipples |
| JIS B1575 ERRATUM 1 | 油脂槍噴嘴(勘誤1) | (Erratum 1) |
| JIS B9913 | 消防用噴嘴連接件的分類及尺寸 消防用ノズルチップの結合部の種類および寸法 | Classification and dimensions of connections for fire department nozzle-tips |
| JIS D2502 | 汽車用散熱器的壓蓋和接管嘴 自動車用ラジエータのプレッシャキャップ及びフィラネック | Pressure caps and filler necks for automobile radiators |
| JIS D3604 | 道路車輛.柴油發動機用燃油噴嘴的形狀及尺寸."S" 規格 | Road vehicles -- Shapes and dimension of fuel injection nozzles for diesel engines -- Size "S" |
| JIS D3631 | 道路車輛.柴油發動機用燃油噴嘴支架的形狀及尺寸."S" 規格 | Road vehicles -- Shapes and dimensions of fuel injection nozzle holders for diesel engines -- Size "S" |
| JIS D3632 | 道路車輛.柴油機燃油噴嘴體的形狀和尺寸.規格P | Road vehicles -- Shapes and dimensions of fuel injection nozzle holders for diesel engines -- Size "P" |
| JIS D3636 | 道路車輛.柴油機燃料噴射泵試驗.樞軸型校準噴嘴 | Road vehicles -- Diesel fuel injection equipment testing -- Pintle type calibrating nozzle |
| JIS D3637-1 | 道路車輛.柴油噴射設備試驗.第1部分:校準噴嘴和固定器組件 | Road vehicles -- Diesel fuel injection equipment testing -- Part 1: Calibrating nozzle and holder assemblies |
| JIS Z8767 | 用臨界流量文丘里噴嘴測定氣體流量 | Measurement of gas flow by means of critical flow Venturi nozzles |
| MT/T 662-1997(2005) | 滾筒采煤機噴霧降塵用噴嘴基本尺寸 | () |
| NF E31-302 | 流量小于或等于200kg/小時家用燃料油自動噴嘴 | (Automatic sprayer burners for domestic fuel oil with a flow rate of up to 200 kg/H.) |
| NF E31-319 | 油壓霧化噴嘴.最低要求.試驗 | (OIL PRESSURE ATOMIZING NOZZLES. MINIMUM REQUIREMENTS. TESTING. (EUROPEAN STANDARD EN 293).) |
| NF E31-320 | 油壓自動噴嘴.角度和噴射特性的測定(歐洲標準EN299) | (Oil pressure atomizing nozzles. Determination of the angle and spray characteristics.) |
| NF E31-354-1 | 供暖鍋爐.第1部分:壓力送風噴嘴式供暖鍋爐.術語、一般要求、試驗和標志 | (Heating boilers. Part 1 : heating boilers with forced draught burners. Terminology, general requirements, testing and marking.) |
| NF L94-111 | 飛機地面注油管噴嘴的插頭和插座 | (Aircraft . Fuel nozzle grounding plugs and sockets.) |
| NF R16-319 | 道路車輛.B型、S規格軸針式噴油嘴用20、21、21.1和27型旋入式噴油嘴保持座 | (Diesel engines - Screw-in injection nozzle holders, types 20, 21, 21.1 and 27 for pintle nozzle size “S“, type “B“.) |
| NF R16-331 | 道路車輛.柴油發動機.22型螺栓固定的噴嘴 | (ROAD VEHICLES. DIESEL ENGINES. SCREW-IN INJECTOR,TYPE 22.) |
| NF R16-332-1 | 道路車輛.燃料噴射設備的試驗.第1部分:噴嘴檢驗及支架裝置 | (Road vehicles. Fuel injection equipment testing. Part 1 : calibrating nozzle and holder assemblies.) |
| NF R16-335 | 道路車輛.壓燃式發動機.擰入式噴嘴座,23型 | (ROAD VEHICLES. COMPRESSION-IGNITION ENGINES. SCREW-IN INJECTION NOZZLE HOLDER,TYPE 23.) |
| NF R16-340 | 柴油發動機.24、25和26和26.1型旋入式噴嘴保持座 | (Diesel engines - Screw-in injection nozzle holders, types 24, 25, 26 and 26.1.) |
| NF S61-820 | 消防和救援設備.消防用手控噴水嘴 | (Firefighting and rescue service equipment - Hand-held nozzles for firefighting.) |
| NF S62-137 | 固定式消防系統.氣體滅火系統用元件.第7部分:CO2系統噴嘴的要求和試驗方法 | (Fixed firefighting systems - Components for gas extinguishing systems - Part 7 : requirements and test methods for nozzles for CO2 systems.) |
| NF T51-075 | 塑料.燃燒特性.針狀噴嘴試驗 | (Plastics. Fire behaviour. Needle burner test.) |
| NF T77-106 | 工業硅樹脂.粘度、擠壓度（流動率）和ＣＡＳＳＯＮ粘度的測定.標準擠壓噴嘴法 | (BASIC SILICONES FOR INDUSTRIAL USE. DETERMINATION OF EXTRUDABILITY (FLUIDITY) AND OF VISCOSITY “CASSON“. METHOD USING STANDARD EXTRUSION NOZZLE.) |
| NF U26-132 | 植物保護裝置.農藥噴灑機具.噴霧器.噴嘴和壓力計的連接尺寸 | (EQUIPMENT FOR CROP PROTECTION. SPRAYERS. CONNECTING DIMENSIONS FOR NOZZLES AND MANOMETERS.) |
| NF U26-134 | 農作物保護設備.噴霧機械.卡口固定噴嘴連接尺寸 | (EQUIPMENT FOR CROP PROTECTION. SPRAYERS. CONNECTING DIMENSIONS FOR NOZZLES WITH BAYONET FIXING.) |
| NF U26-136 | 作物保護設備.空氣噴霧機械.噴嘴旋轉螺母的尺寸 | (EQUIPMENT FOR CROP PROTECTION. AIR-ASSISTED SPRAYERS. DIMENSIONS OF NOZZLE SWIVEL NUTS.) |
| NF X10-102-3 | 用插入圓截面管道中的壓差裝置測量流體流量.第3部分:噴嘴和文杜利噴嘴 | (Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3 : nozzles and Venturi nozzles.) |
| QB 1334 | 水嘴通用技術條件 | () |
| QB 2806 | 溫控水嘴 | Thermostatic faucets |
| QB/T 3895 | 旋塞式熱水嘴 | Pluged hot-Water taps |
| SH/T 0103 | 含聚合物油剪切安定性的測定 柴油噴嘴法 | Standard test method for shear stability of polymer containing fluids using a european diesel injector apparatus |
| SH/T 0764 | 柴油機噴嘴結焦試驗方法（XUD-9法） | () |
| SY/T 5906 | 配水嘴嘴損曲線圖版制作方法 | () |
| UL 2351 | 防火設施用噴嘴 | (Spray nozzles for fire-protection service ) |
| YB/T 4087-1982(2005) | 冶金噴嘴 | () |
| prEN 12067-2 | 燃?xì)鈬娮旌腿細庋b置用燃?xì)?空氣混合調節器 第2部分：電子型 | Gas/air ratio controls for gas burners and gas burning appliances - Part 2: Electronic types |
| prEN 12881-1 | 傳輸帶 燃燒模擬法可燃性試驗 第1部分：兩米單噴嘴丙烷坑道試驗 | Conveyor belts - Fire simulation flammability testing - Part 1: Two metre single burner propane gallery test |
| prEN 3908 | 航空航天系列 鈍化耐腐蝕鋼潤滑軸向噴嘴 | Aerospace series - Nipples, lubricating, axial type, in corrosion resisting steel, passivated |
| prEN ISO 20844 | 石油及石油產品 用柴油機噴嘴測定含聚合物油類的剪切穩定性 | Petroleum and related products - Determination of the shear stability of polymer-containing oils using a diesel injector nozzle (ISO/DIS 20844:2002) |
| 編號 | 中文名稱 | 英文名稱 |