微信掃一掃，立即回復！
| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| IEC 60962 | 汽輪機用石油潤滑油的維護與使用指南 | Maintenance and use guide for petroleum lubricating oils for steam turbines |
| IEC 61221 | 石油產品和潤滑劑.三芳基磷酸酯渦輪機控制液(ISO-L-TCD類).規范 | Petroleum products and lubricants - Triaryl phosphate ester turbine control fluids (category ISO-L-TCD) - Specifications |
| ISO 10239 Technical Corrigendum 1 | 小艇 液化石油氣(LPG)系統 技術勘誤1 | Small craft - Liquefied petroleum gas (LPG) systems; Technical corrigendum 1 |
| ISO 10239 | 小艇 液化石油氣(LPG)系統 | Small craft - Liquefied petroleum gas (LPG) systems |
| ISO 10307-1 Technical Corrigendum 1 | 石油產品 殘留在燃料油中的總沉淀物 第1部分:熱過濾測定法 技術勘誤1 | Petroleum products - Total sediment in residual fuel oils - Part 1: Determination by hot filtration; Technical Corrigendum 1 |
| ISO 10307-1 | 石油產品 殘留在燃料油中的總沉淀物 第1部分:熱過濾測定法 | Petroleum products; total sediment in residual fuel oils; part 1: determination by hot filtration |
| ISO 10307-2 | 石油產品 殘留在燃料油中的總沉淀物 第2部分:老化程序測定法 | Petroleum products; total sediment in residual fuel oils; part 2: determination using standard procedures for ageing |
| ISO 10370 Technical Corrigendum 1 | 石油產品.殘?zhí)嫉臏y(cè)定.數量法.技術勘誤1 | Petroleum products - Determination of carbon residue - Micro method; Technical Corrigendum 1 |
| ISO 10370 | 石油產品 殘?zhí)嫉臏y(cè)定 數量法 | Petroleum products; determination of carbon residue; micro method |
| ISO 10400 | 石油和天然氣工業 套管、油管、鉆桿和管線管性能公式與計算 | Petroleum and natural gas industries; formulae and calculation for casing, tubing, drill pipe and line pipe properties |
| ISO 10405 | 石油和天然氣工業 套管和油管的維護和使用 | Petroleum and natural gas industries - Care and use of casing and tubing |
| ISO 10407 | 石油和天然氣工業 鉆井和生產設備 鉆柱設計和操作極限 | Petroleum and natural gas industries; drilling and production equipment; drill stem design and operating limits |
| ISO 10414-1 | 石油和天然氣工業 鉆探油液的現場試驗 第1部分：水基油液 | Petroleum and natural gas industries - Field testing of drilling fluids - Part 1: Water-based fluids |
| ISO 10414-2 | 石油和天然氣工業.鉆井液的現場試驗.第2部分:以油為基礎的液體 | Petroleum and natural gas industries - Field testing of drilling fluids - Part 2: Oil-based fluids |
| ISO 10416 | 石油和天然氣工業.鉆用沖洗液.實驗室試驗 | Petroleum and natural gas industries - Drilling fluids - Laboratory testing |
| ISO 10417 | 石油和天然氣工業.井下安全閥系統.設計、安裝、操作和修整 | Petroleum and natural gas industries - Subsurface safety valve systems - Design, installation, operation and redress |
| ISO 10418 | 石油和天然氣工業.近海生產裝置.基礎表面操作安全系統 | Petroleum and natural gas industries - Offshore production installations - Basic surface process safety systems |
| ISO 10423 | 石油和天然氣工業.鉆井和開采設備.井口設施和采油樹設備 | Petroleum and natural gas industries - Drilling and production equipment - Wellhead and christmas tree equipment |
| ISO 10424-1 | 石油和天然氣工業.旋轉鉆孔設備.第1部分:旋轉鉆桿構件 | Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill stem elements |
| ISO 10425 | 石油和天然氣工業用鋼絲繩.最低要求和驗收條件 | Steel wire ropes for the petroleum and natural gas industries - Minimum requirements and terms of acceptance |
| ISO 10426-1 | 石油和天然氣工業.油井固井用水泥和材料.第1部分:規范 | Petroleum and natural gas industries - Cements and materials for well cementing - Part 1: Specification |
| ISO 10426-2 AMD 1 | 石油和天然氣工業.油井固井用水泥和材料.第2部分:油井用水泥的試驗.修改件1:親水性試驗 | Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements; Amendment 1: Water-wetting capability testing |
| ISO 10426-2 Technical Corrigendum 1 | 石油和天然氣工業.油井固井用水泥和材料.第2部分:油井用水泥測試 | Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements |
| ISO 10426-2 | 石油和天然氣工業.油井固井用水泥和材料.第2部分:油井用水泥的試驗 | Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements |
| ISO 10426-3 | 石油和天然氣工業.油井固井用水泥和材料.第3部分:深水油井水泥成分的測試 | Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well cement formulations |
| ISO 10426-4 | 石油和天然氣工業.油井固井用水泥和材料.第4部分:在大氣壓力下泡沫水泥漿的制備和檢驗 | Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure |
| ISO 10426-5 | 石油和天然氣工業.油井固井用水泥和材料.第5部分:在大氣壓力下固井水泥加工制劑的收縮和膨脹的測定 | Petroleum and natural gas industries - Cements and materials for well cementing - Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure |
| ISO 10427-1 | 石油和天然氣工業 套管扶正器 第1部分：弓性彈簧套管扶正器 | Petroleum and natural gas industries - Casing centralizers - Part 1: Bow-spring casing centralizers |
| ISO 10427-2 | 石油和天然氣工業.固井用設備.第2部分:扶正器的放置和限動環的檢測 | Petroleum and natural gas industries - Equipment for well cementing - Part 2: Centralizer placement and stop-collar testing |
| ISO 10427-3 | 石油和天然氣工業.固井用設備.第3部分:固井浮動設備的性能試驗 | Petroleum and natural gas industries - Equipment for well cementing - Part 3: Performance testing of cementing float equipment |
| ISO 10428 | 石油和天然氣工業 抽油桿(抽油桿短節 光桿 接箍和變徑接箍) 規范 | Petroleum and natural gas industries; sucker rods (pony-rods, polished rods, couplings and sub-couplings); specification |
| ISO 10431 | 石油和天然氣工業 抽油機 規范 | Petroleum and natural gas industries; pumping units; specification |
| ISO 10432 | 石油和天然氣工業.下降孔設備.地下安全閥設備 | Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment |
| ISO 10434 | 石油、石油化學和相關工業用栓接帽狀鋼閘閥 | Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries |
| ISO 10437 | 石油、石油化學和天然氣工業.專用汽輪機設備 | Petroleum, petrochemical and natural gas industries - Steam turbines - Special-purpose applications |
| ISO 10438-1 | 石油、化工和天然氣工業.潤滑、油封、控油系統和輔助裝置.第1部分:一般要求 | Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements |
| ISO 10438-2 | 石油、化工和天然氣工業.潤滑、油封、控油系統和輔助裝置.第2部分:專用油系統 | Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2: Special-purpose oil systems |
| ISO 10438-3 | 石油、化工和天然氣工業.潤滑、油封、控油系統和輔助裝置.第3部分:通用油系統 | Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems |
| ISO 10438-4 | 石油、化工和天然氣工業.潤滑、油封、控油系統和輔助裝置.第4部分:自動氣封支撐系統 | Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 4: Self-acting gas seal support systems |
| ISO 10439 | 石油、化學和氣體工業.離心壓縮機 | Petroleum, chemical and gas service industries - Centrifugal compressors |
| ISO 10440-1 | 石油、石化和天然氣工業.旋轉型容積式壓縮機.第1部分:加工壓縮機 | Petroleum, petrochemical and natural gas industries - Rotary-type positive-displacement compressors - Part 1: Process compressors |
| ISO 10440-2 | 石油和天然氣工業 旋轉型容積式壓縮機 第2部分：封裝的空氣壓縮機（無油） | Petroleum and natural gas industries - Rotary-type positive-displacement compressors - Part 2: Packaged air compressors (oil-free) |
| ISO 10441 | 石油、石化和天然氣工業.機械動力傳輸用撓性聯軸節.特殊應用 | Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications |
| ISO 10442 | 石油、化學和氣體設備工業.包裝的整體式齒輪分離空氣壓縮機 | Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors |
| ISO 10464 | 氣瓶.液化石油氣(LPG)用可再填充的焊接鋼制氣瓶.周期檢驗和試驗 | Gas cylinders - Refillable welded steel cylinders for liquefied petroleum gas (LPG) - Periodic inspection and testing |
| ISO 10478 | 石油產品 中間燃份油中的鋁和硅的測定 感應耦合等離子發射和原子吸收光譜法 | Petroleum products - Determination of aluminium and silicon in fuel oils - Inductively coupled plasma emission and atomic absorption spectroscopy methods |
| ISO 10691 | 氣瓶.液化石油氣(LPG)用可再填充的焊接鋼制氣瓶.裝填前后及裝填期間的檢驗規程 | Gas cylinders - Refillable welded steel cylinders for liquified petroleum gas (LPG) - Procedures for checking before, during and after filling |
| ISO 11007 | 石油產品和潤滑劑 潤滑脂防銹性能的測定 | Petroleum products and lubricants - Determination of rust-prevention characteristics of lubricating greases |
| ISO 11009 | 石油產品和潤滑劑 潤滑脂抗水淋特性的測定 | Petroleum products and lubricants - Determination of water washout characteristics of lubricating greases |
| ISO 11223 | 石油和液態石油產品.直接靜態測量.通過靜壓油罐計量測量立式貯罐容量 | Petroleum and liquid petroleum products - Direct static measurements - Measurement of content of vertical storage tanks by hydrostatic tank gauging |
| ISO 11563 | 原油和石油制品.散貨運輸.實現管道滿度的指南 | Crude petroleum and petroleum products - Bulk cargo transfer - Guidelines for achieving the fullness of pipelines |
| ISO 11759 | 輸送液化石油氣用橡膠軟管和軟管組件(LPGs) 規范 | Rubber hoses and hose assemblies for dispensing liquefied petroleum gases (LPGs) - Specification |
| ISO 11960 Technical Corrigendum 1 | 石油和天然氣工業.油井套管或油管用鋼管.技術勘誤1 | Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells; Technical Corrigendum 1 |
| ISO 11960 | 石油和天然氣工業.油井套管和油管用鋼管 | Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells |
| ISO 11961 | 石油和天然氣工業 鉆井桿用鋼管 規范 | Petroleum and natural gas industries - Steel pipes for use as drill pipe - Specification |
| ISO 12185 Technical Corrigendum 1 | 原油和石油產品 密度的測定 振動的U形管法 技術勘誤1 | Crude petroleum and petroleum products - Determination of density - Oscillating U-tube method; Technical Corrigendum 1 |
| ISO 12185 | 原油和石油產品 密度的測定 振動的U形管法 | Crude petroleum and petroleum products - Determination of density - Oscillating U-tube method |
| ISO 12205 | 石油產品 中間餾份燃料的氧化安定性的測定 | Petroleum products - Determination of the oxidation stability of middle-distillate fuels |
| ISO 12917-1 | 石油和液化石油產品.臥式圓形油罐的校正.第1部分:手工法 | Petroleum and liquid petroleum products - Calibration of horizontal cylindrical tanks - Part 1: Manuel methods |
| ISO 12917-2 | 石油和液態石油產品.臥式圓筒狀油罐的標定.第2部分:光電內測距法 | Petroleum and liquid petroleum products - Calibration of horizontal cylindrical tanks - Part 2: Internal electro-optical distance-ranging method |
| ISO 12937 | 石油產品 水分的測定 庫侖卡爾·費休滴定法 | Petroleum products - Determination of water - Coulometric Karl Fischer titration method |
| ISO 13357-1 | 石油產品.潤滑油可過濾性測定.第2部分:水中過濾油的程序 | Petroleum products - Determination of the filterability of lubricating oils - Part 1: Procedure for oils in the presence of water |
| ISO 13357-2 | 石油產品.潤滑油的可過濾性測定.第2部分:干性油技術 | Petroleum products - Determination of the filterability of lubricating oils - Part 2: Procedure for dry oils |
| ISO 13500 | 石油和天然氣工業.鉆井液體材料.規范和測試 | Petroleum and natural gas industries - Drilling fluid materials - Specifications and tests |
| ISO 13501 | 石油和天然氣工業.鉆井液.加工系統評價 | Petroleum and natural gas industries - Drilling fluids - Processing systems evaluation |
| ISO 13503-1 Technical Corrigendum 1 | 石油和天然氣工業.完井液和材料.第1部分:完井液粘性測量.技術勘誤1 | Petroleum and natural gas industries - Completion fluids and materials - Part 1: Measurement of viscous properties of completion fluids; Technical Corrigendum 1 |
| ISO 13503-1 | 石油和天然氣工業.完井液和材料.第1部分:完井液粘著特性的測量 | Petroleum and natural gas industries - Completion fluids and materials - Part 1: Measurement of viscous properties of completion fluids |
| ISO 13503-2 | 石油和天然氣工業.完井液和材料.第2部分:高壓水砂破裂法和礫石包裝作業用支撐劑性能測定 | Petroleum and natural gas industries - Completion fluids and materials - Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations |
| ISO 13503-3 Technical Corrigendum 1 | 石油和天然氣工業.完井液和材料.第3部分:重鹽水的試驗.技術勘誤1 | Petroleum and natural gas industries - Completion fluids and materials - Part 3: Testing of heavy brines; Technical Corrigendum 1 |
| ISO 13503-3 | 石油和天然氣工業.完井液和材料.第3部分:重鹽水的試驗 | Petroleum and natural gas industries - Completion fluids and materials - Part 3: Testing of heavy brines |
| ISO 13503-4 | 石油和天然氣工業.完井液和材料.第4部分:在靜態條件下測量外部碰擊和砂礫包裝液體泄露程序 | Petroleum and natural gas industries - Completion fluids and materials - Part 4: Procedure for measuring stimulation and gravel-pack fluid leakoff under static conditions |
| ISO 13503-5 | 石油和天然氣工業.完井液和材料.第5部分：測量重鹽水長期電導率程序.技術勘誤1 | Petroleum and natural gas industries - Completion fluids and materials - Part 5: Procedures for measuring the long-term conductivity of proppants |
| ISO 13533 Technical Corrigendum 1 | 石油和天然氣工業.鉆井和生產設備.鉆通設備.技術勘誤1 | Petroleum and natural gas industries - Drilling and production equipment - Drill-through equipment; Technical Corrigendum 1 |
| ISO 13533 | 石油和天然氣工業 鉆井和生產設備 鉆井設備 | Petroleum and natural gas industries - Drilling and production equipment - Drill-through equipment |
| ISO 13534 | 石油和天然氣工業 鉆井和生產設備 提升設備的檢查、維護、修理和再制造 | Petroleum and natural gas industries - Drilling and production equipment - Inspection, maintenance, repair and remanufacture of hoisting equipment |
| ISO 13535 | 石油和天然氣工業 鉆井和生產設備 提升設備 | Petroleum and natural gas industries - Drilling and production equipment - Hoisting equipment |
| ISO 13623 | 石油和天然氣工業.管道輸送系統 | Petroleum and natural gas industries - Pipeline transportation systems |
| ISO 13625 | 石油和天然氣工業.鉆井和生產設備.海洋鉆井隔水導管聯接器 | Petroleum and natural gas industries - Drilling and production equipment - Marine drilling riser couplings |
| ISO 13626 | 石油和天然氣工業.鉆井和生產設備.鉆井和井檢修結構 | Petroleum and natural gas industries - Drilling and production equipment - Drilling and well-servicing structures |
| ISO 13628-1 | 石油和天然器工業.水下采油系統的設計和操作.第1部分:一般要求和建議 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations |
| ISO 13628-10 | 石油和天然氣工業.水下采油系統的設計和操作.第10部分:連接柔性管規范 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 10: Specification for bonded flexible pipe |
| ISO 13628-11 | 石油和天然氣工業.水底生產系統的設計和運行.第11部分:海底和海上設備用軟管系統 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 11: Flexible pipe systems for subsea and marine applications |
| ISO 13628-2 | 石油和天然氣工業.水下采油系統的設計和操作.第2部分:海底和海洋設備用游離軟管系統 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 2: Unbonded flexible pipe systems for subsea and marine applications |
| ISO 13628-3 | 石油和天然氣工業 水下采油系統的設計和操作 第3部分:通流線系統 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 3: Through flowtime (TFL) systems |
| ISO 13628-4 | 石油和天然氣工業 水下采油系統的設計和操作 第4部分:井口和采油樹設備 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 4: Subsea wellhead and tree equipment |
| ISO 13628-5 | 石油和天然氣工業.水下采油系統的設計和操作.第5部分:水下纜線和管道 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals |
| ISO 13628-6 | 石油和天然氣工業.水下采油系統的設計和操作.第6部分:水下生產控制系統 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 6: Subsea production control systems |
| ISO 13628-7 | 石油和天然氣工業.水下采油系統的設計和操作.第7部分:完井/修井提升管系統 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 7: Completion/workover riser systems |
| ISO 13628-8 Technical Corrigendum 1 | 石油和天然氣工業.水下生產系統的設計和操作.第8部分:水下生產系統上的遙控運載工具接口.技術勘誤1 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems; Technical Corrigendum 1 |
| ISO 13628-8 | 石油和天然氣工業.水下生產系統的設計和操作.第8部分:水下生產系統上的遙控運載工具接口 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems |
| ISO 13628-9 | 石油和天然氣工業 水下采油系統的設計和操作 第9部分:遙控設備干預系統 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 9: Remotely Operated Tools (ROT) intervention systems |
| ISO 13631 | 石油和天然氣工業.包裝用往復式氣體壓縮機 | Petroleum and natural gas industries - Packaged reciprocating gas compressors |
| ISO 13678 Technical Corrigendum 1 | 石油和天然氣工業.對套管、管道和管線用的螺紋油的評定和試驗.技術勘誤1 | Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing and line pipe; Technical Corrigendum 1 |
| ISO 13678 | 石油和天然氣工業 對套管、管道和管線用的螺紋絕緣膏的評價和試驗 | Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing and line pipe |
| ISO 13679 | 石油和天然氣工業.套管和管連接的測試程序 | Petroleum and natural gas industries - Procedures for testing casing and tubing connections |
| ISO 13680 Technical Corrigendum 2 | 石油和天然氣工業.用作套管、油管和接箍的防腐合金無縫鋼管.交貨技術條件.技術勘誤2 | Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions; Technical Corrigendum 2 |
| ISO 13680 | 石油和天然氣工業 用作套管、油管和接箍的防腐合金無縫鋼管交貨技術條件 | Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions |
| ISO 13691 | 石油和天然氣工業 特殊用途高速傳動裝置 | Petroleum and natural gas industries - High-speed special-purpose gear units |
| ISO 13702 | 石油和天然氣工業 對海上開發安裝中著火和爆炸的控制和減弱 要求和指南 | Petroleum and natural gas industries - Control and mitigation of fires and explosions on offshore production installations - Requirements and guidelines |
| ISO 13703 Technical Corrigendum 1 | 石油和天然氣工業.近海生產平臺上管道系統的設計和安裝.技術勘誤1 | Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms; Technical Corrigendum 1 |
| ISO 13703 | 石油和天然氣工業 海上開采平臺上管道系統的設計和安裝 | Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms |
| ISO 13705 | 石油、石化和天然氣工業.一般煉油廠火力加熱器 | Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service |
| ISO 13706 | 石油、石化和天然氣工業.風冷熱交換器 | Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers |
| ISO 13707 | 石油和天然氣工業 往復式壓縮機 | Petroleum and natural gas industries - Reciprocating compressors |
| ISO 13709 | 石油、石油化工和天然氣工業用離心泵 | Centrifugal pumps for petroleum, petrochemical and natural gas industries |
| ISO 13710 | 石油、石油化學和天然氣工業.往復式變?nèi)菡婵毡? | Petroleum, petrochemical and natural gas industries - Reciprocating positive displacement pumps |
| ISO 13736 | 石油產品和其他液體 閃點的測定 阿貝爾閉口杯法 | Petroleum products and other liquids - Determination of flash point - Abel closed cup method |
| ISO 13737 | 石油產品和潤滑劑.潤滑劑脂的低溫針入度的測定 | Petroleum products and lubricants - Determination of low-temperature cone penetration of lubricating greases |
| ISO 13740 | 原油和石油產品 輸入量的計算 在遠洋運輸中儲油罐載負狀態下容器組合的經驗參數和減載下的容器組合經驗參數 | Crude petroleum and petroleum products - Transfer accountability - Assessment of vessel experience factor on loading (VEFL) and vessel experience factor on discharging (VEFD) on ocean-going tanker vessels |
| ISO 13757 | 液化石油氣 油殘余物的測定 高溫法 | Liquefied petroleum gases - Determination of oily residues - High-temperature method |
| ISO 13758 | 液化石油氣 評價丙烷干燥度 閥凍結法 | Liquefied petroleum gases - Assessment of the dryness of propane - Valve freeze method |
| ISO 13759 | 石油產品 柴油中硝酸烷基酯含量的測定 分光光度法 | Petroleum products - Determination of alkyl nitrate in diesel fuels - Spectrometric method |
| ISO 13775-2 | 汽車用熱塑管和軟管 第2部分:石油類燃料上應用 | Thermoplastic tubing and hoses for automotive use - Part 2: Petroleum-based-fuel applications |
| ISO 13819-2 | 石油和天然氣工業 海上結構 第2部分:固定的鋼結構 | Petroleum and natural gas industries - Offshore structures - Part 2: Fixed steel structures |
| ISO 13847 Technical Corrigendum 1 | 石油和天然氣工業.管道輸送系統.管道焊接.技術勘誤1 | Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines; Technical Corrigendum 1 |
| ISO 13847 | 石油和天然氣工業 管道輸送系統 管道的焊接 | Petroleum and natural gas industrie - Pipeline transportation systems - Welding of pipelines |
| ISO 13879 | 石油和天然氣工業 功能規范的內容和起草 | Petroleum and natural gas industries - Content and drafting of a functional specification |
| ISO 13880 | 石油和天然氣工業 技術規范的內容和起草 | Petroleum and natural gas industries - Content and drafting of a technical specification |
| ISO 14224 | 石油、石化產品和天然氣工業.設備可靠性和維修數據的采集與交換 | Petroleum, petrochemical and natural gas industries - Collection and exchange of reliability and maintenance data for equipment |
| ISO 14245 | 氣瓶.液化石油氣瓶閥門的規范和試驗.自閉合 | Gas cylinders - Specifications and testing of LPG cylinder valves - Self-closing |
| ISO 14310 | 石油和天然氣工業 下井設備 封隔器和橋塞 | Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs |
| ISO 14313 | 石油和天然氣工業 管道輸送系統 管道閥 | Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves |
| ISO 14435 | 鋁生產用含碳材料.石油焦.用感應耦合等離子體原子發射光譜測定法測定痕量金屬 | Carbonaceous materials for the production of aluminium - Petroleum coke - Determination of trace metals by inductively coupled plasma atomic emission spectrometry |
| ISO 14596 | 石油制品.硫含量的測定.波長色散X-射線熒光光譜法 | Petroleum products - Determination of sulfur content - Wavelength-dispersive X-ray fluorescence spectrometry |
| ISO 14597 | 石油產品 釩和鎳含量的測定 波長色散X-射線熒光光譜法 | Petroleum products - Determination of vanadium and nickel content - Wavelength-dispersive X-ray fluorescence spectrometry |
| ISO 14691 | 石油和天然氣工業 機械動力傳輸用撓性接箍 一般用途 | Petroleum and natural gas industries - Flexible couplings for mechanical power transmission - General purpose applications |
| ISO 14692-1 | 石油和天然氣工業.玻璃纖維增強塑料管.第1部分:詞匯、符號、應用和材料 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials |
| ISO 14692-2 Technical Corrigendum 1 | 石油和天然氣工業.玻璃增強塑料(GRP)管.第2部分:合格鑒定和制造.技術勘誤1 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture; Technical Corrigendum 1 |
| ISO 14692-2 | 石油和天然氣工業.玻璃纖維增強塑料管.第2部分:合格鑒定和制造 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture |
| ISO 14692-3 Technical Corrigendum 1 | 石油和天然氣工業.玻璃增強塑料(GRP)管.第3部分:系統設計.技術勘誤1 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design; Technical Corrigendum 1 |
| ISO 14692-3 | 石油和天然氣工業.玻璃纖維增強塑料管.第3部分:系統管道 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System piping |
| ISO 14692-4 Technical Corrigendum 1 | 石油和天然氣工業.玻璃纖維增強塑料管.第4部分:制作、安裝和操作;技術勘誤1 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation; Technical Corrigendum 1 |
| ISO 14692-4 | 石油和天然氣工業.玻璃纖維增強塑料管.第4部分:制作、安裝和操作 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation |
| ISO 14693 | 石油和天然氣工業.鉆井和油井輔助設備 | Petroleum and natural gas industries - Drilling and well-servicing equipment |
| ISO 14723 | 石油和天然氣工業 管道輸送系統 海底管道閥 | Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves |
| ISO 14935 | 石油和相關產品 難燃液芯帶燃燒持久度的測定 | Petroleum and related products - Determination of wick flame persistence of fire-resistant fluids |
| ISO 15029-1 | 石油和相關產品 難燃液體噴射燃燒特性的測定 第1部分:噴流燃燒持久度 空錐噴嘴法 | Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Part 1: Spray flame persistence - Hollow-cone nozzle method |
| ISO 15136-1 | 石油和天然氣工業用下降孔設備 人工升降機用推進腔體泵系統 第1部分：泵 | Downhole equipment for petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 1: Pumps |
| ISO 15136-2 | 石油和天然氣工業.人工升降機用推進腔體泵系統.第2部分:表面?zhèn)鲃?dòng)系統 | Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 2: Surface-drive systems |
| ISO 15138 Technical Corrigendum 1 | 石油和天然氣工業 海上開采裝置 供暖 通風和空氣調節 技術勘誤1 | Petroleum and natural gas industries - Offshore production installations - Heating, ventilation and air-conditioning; Technical Corrigendum 1 |
| ISO 15138 | 石油和天然氣工業 海上開采裝置 供暖 通風和空氣調節 | Petroleum and natural gas industries - Offshore production installations - Heating, ventilation and air-conditioning |
| ISO 15156-1 Technical Corrigendum 1 | 石油和天然氣工業.油、氣生產中含硫化氫(H2S)環境下使用的材料.第1部分:耐裂化材料選擇的一般原則.技術勘誤 | Petroleum and natural gas industries - Materials for use in H<(Index)2>S-containing environments in oil and gas production - Part 1: General principles for selection of cracking-resistant materials; Technical Corrigendum 1 |
| ISO 15156-1 | 石油和天然氣工業 石油制品和天然氣生產中含硫化氫（H2S）環境下使用的材料 第1部分：耐破裂材料的一般選 | Petroleum and natural gas industries - Materials for use in H<(Index)2>S-containing environments in oil and gas production - Part 1: General principles for selection of cracking-resistant materials |
| ISO 15156-2 Technical Corrigendum 1 | 石油和天然氣工業.油、氣生產中含硫化氫(H2S)環境下使用的材料.第2部分:耐裂化碳鋼和低合金鋼及鑄鐵的使用. | Petroleum and natural gas industries - Materials for use in H<(Index)2>S-containing environments in oil and gas production - Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons; Technical Corrigendum 1 |
| ISO 15156-2 | 石油和天然氣工業.油、氣生產中含硫化氫(H2S)環境下使用的材料.第2部分:耐裂化碳和低合金鋼及鑄鐵的使用 | Petroleum and natural gas industries - Materials for use in H<(Index)2>S-containing environments in oil and gas production - Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons |
| ISO 15156-3 Technical Corrigendum 1 | 石油和天然氣工業.油、氣生產中含硫化氫(H2S)環境下使用的材料.第1部分:耐裂化CRAs(防腐蝕合金)和其他合金. | Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys; Technical Corrigendum 1 |
| ISO 15156-3 Technical Corrigendum 2 | 石油和天然氣工業.油、氣生產中含硫化氫(H2S)環境下使用的材料.第1部分:耐裂化CRAs(防腐蝕合金)和其他合金. | Petroleum and natural gas industries - Materials for use in H<(Index)2>S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys; Technical Corrigendum 2 |
| ISO 15156-3 | 石油和天然氣工業.油、氣生產中含硫化氫(H2S)環境下使用的材料.第3部分:耐裂化CRAs(耐腐蝕合金)和其他合金 | Petroleum and natural gas industries - Materials for use in H<(Index)2>S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys |
| ISO 15167 | 石油產品 中間餾份燃料顆粒物含量的測定 實驗室過濾法 | Petroleum products - Determination of particulate content of middle distillate fuels - Laboratory filtration method |
| ISO 15169 | 石油和液體石油產品.用混合油罐測量系統測定立式油罐所含烴類的體積、密度和質量 | Petroleum and liquid petroleum products - Determination of volume, density and mass of the hydrocarbon content of vertical cylindrical tanks by hybrid tank measurement systems |
| ISO 15463 | 石油和天然氣工業.新套管、管和平端鉆管的現場檢驗 | Petroleum and natural gas industries - Field inspection of new casing, tubing and plain-end drill pipe |
| ISO 15544 | 石油和天然氣工業 海上開采裝置 緊急反應的要求和指南 | Petroleum and natural gas industries - Offshore production installations - Requirements and guidelines for emergency response |
| ISO 15546 | 石油和天然氣工業.鋁合金鉆桿 | Petroleum and natural gas industries - Aluminium alloy drill pipe |
| ISO 15547-1 | 石油、石化和天然氣工業.板式熱交換器.第1部分:板框式熱交換器 | Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 1: Plate-and-frame heat exchangers |
| ISO 15547-2 | 石油、石化和天然氣工業.板式熱交換器.第2部分:銅焊鋁板熱交換器 | Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 2: Brazed aluminium plate-fin heat exchangers |
| ISO 15589-1 | 石油和天然氣工業.管道運輸系統的陰極保護.第1部分:陸地管線 | Petroleum and natural gas industries - Cathodic protection of pipeline transportation systems - Part 1: On-land pipelines |
| ISO 15589-2 | 石油和天然氣工業.管道運輸系統的陰極保護.第2部分:海上管線 | Petroleum and natural gas industries - Cathodic protection of pipeline transportation systems - Part 2: Offshore pipelines |
| ISO 15590-1 | 石油和天然氣工業 管道輸送系統用誘導彎頭、管件和法蘭 第1部分：誘導彎頭 | Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends |
| ISO 15590-2 | 石油和天然氣工業.管道輸送系統用進氣彎管、管件和法蘭.第2部分:管件 | Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings |
| ISO 15590-3 | 石油和天然氣工業.管道輸送系統用進氣彎頭、管件和法蘭.第3部分:法蘭 | Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges |
| ISO 15597 | 石油及有關產品 氯和溴含量的測定 波長散射X射線熒光光譜測定法 | Petroleum and related products - Determination of chlorine and bromine content - Wavelength-dispersive X-ray fluorescence spectrometry |
| ISO 15649 | 石油和天然氣工業 管道 | Petroleum and natural gas industries - Piping |
| ISO 15663-1 | 石油和天然氣工業 壽命周期成本 第1部分:方法學 | Petroleum and natural gas industries - Life cycle costing - Part 1: Methodology |
| ISO 15663-2 | 石油和天然氣工業 壽命周期成本 第2部分：方法學應用指南和計算方法 | Petroleum and natural gas industries - Life cycle costing - Part 2: Guidance on application of methodology and calculation methods |
| ISO 15663-3 | 石油天然氣工業.壽命周期費用分析.第3部分:實施指南 | Petroleum and natural gas industries - Life-cycle costing - Part 3: Implementation guidelines |
| ISO 15761 | 石油和天然氣工業用尺寸為DN 100及更小的鋼閘閥、球閥和止回閥 | Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries |
| ISO 15911 | 石油產品 用氫含量數據評定航空渦輪燃燒的凈比能 | Petroleum products - Estmation of net specific emergy of eviation turbine fuels using hydrogen content data |
| ISO 15995 | 氣瓶.液化石油氣瓶閥門的規范和試驗.手工操作 | Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated |
| ISO 16070 | 石油和天然氣工業.下井設備.鎖芯軸和落地接頭 | Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples |
| ISO 16708 | 石油和天然氣工業.管道傳輸系統.基于可靠性的極限狀態法 | Petroleum and natural gas industries - Pipeline transportation systems - Reliability-based limit state methods |
| ISO 16812 | 石油、石化和天然氣工業.殼管式熱交換器 | Petroleum, petrochemical and natural gas industries - Shell-and-tube heat exchangers |
| ISO 17078-1 | 石油和天然氣工業.鉆井和生產設備.第1部分:偏心軸 | Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-pocket mandrels |
| ISO 17292 | 石油、石化和相關工業用金屬球閥 | Metal ball valves for petroleum, petrochemical and allied industries |
| ISO 17776 | 石油和天然氣工業 海上開采裝置 危險識別和風險評估用方法和技術指南 | Petroleum and natural gas industries - Offshore production installations - Guidelines on tools and techniques for hazard identification and risk assessment |
| ISO 19900 | 石油和天然氣工業.近海結構的一般要求 | Petroleum and natural gas industries - General requirements for offshore structures |
| ISO 19901-1 | 石油和天然氣工業.海上建筑物的特殊要求.第1部分:Metocean設計和運行研究 | Petroleum and natural gas industries - Specific requirements for offshore structures - Part 1: Metocean design and operating considerations |
| ISO 19901-2 | 石油和天然氣工業.近海建筑物的特殊要求.第2部分:地震設計規程和標準 | Petroleum and natural gas industries - Specific requirements for offshore structures - Part 2: Seismic design procedures and criteria |
| ISO 19901-4 | 石油和天然氣工業.近海建筑物的特殊要求.第4部分:土工和基礎設計考慮 | Petroleum and natural gas industries - Specific requirements for offshore structures - Part 4: Geotechnical and foundation design considerations |
| ISO 19901-5 | 石油和天然氣工業.海上建筑物的特殊要求.第5部分:設計和施工過程中的重量控制 | Petroleum and natural gas industries - Specific requirements for offshore structures - Part 5: Weight control during engineering and construction |
| ISO 19901-7 | 石油和天然氣工業.海上建筑物的特殊要求.第7部分:浮動式海上建筑物和移動式海上設備用保持系統 | Petroleum and natural gas industries - Specific requirements for offshore structures - Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units |
| ISO 19903 | 石油和天然氣工業.海上固定的混凝土建筑物 | Petroleum and natural gas industries - Fixed concrete offshore structures |
| ISO 19904-1 | 石油和天然氣工業.漂浮離岸設施.第1部分:單體船、半潛水船和輕甲板船 | Petroleum and natural gas industries - Floating offshore structures - Part 1: Monohulls, semi-submersibles and spars |
| ISO 1998-1 Technical Corrigendum 1 | 石油工業 名詞術語 第1部分:原料和產品 技術勘誤1 兩種語言版 | Petroleum industry - Terminology - Part 1: Raw materials and products; Technical Corrigendum 1 |
| ISO 1998-1 | 石油工業 名詞術語 第1部分:原料和產品 兩種語言版 | Petroleum industry - Terminology - Part 1: Raw materials and products |
| ISO 1998-2 | 石油工業 名詞術語 第2部分:性質和試驗 兩種語言版 | Petroleum industry - Terminology - Part 2: Properties and tests |
| ISO 1998-3 | 石油工業 名詞術語 第3部分:勘探和采油 兩種語言版 | Petroleum industry - Terminology - Part 3: Exploration and production |
| ISO 1998-4 | 石油工業 名詞術語 第4部分:煉制 兩種語言版 | Petroleum industry - Terminology - Part 4: Refining |
| ISO 1998-5 Technical Corrigendum 1 | 石油工業 名詞術語 第5部分:運輸、儲存、分配 技術勘誤1 兩種語言版 | Petroleum industry - Terminology - Part 5: Transport, storage, distribution; Technical Corrigendum 1 |
| ISO 1998-5 | 石油工業 名詞術語 第5部分:運輸、儲存、分配 兩種語言版 | Petroleum industry - Terminology - Part 5: Transport, storage, distribution |
| ISO 1998-6 | 石油工業 名詞術語 第6部分:計量 兩種語言版 | Petroleum industry - Terminology - Part 6: Measurement |
| ISO 1998-7 | 石油工業 名詞術語 第7部分:其他術語 兩種語言版 | Petroleum industry - Terminology - Part 7: Miscellaneous terms |
| ISO 1998-99 | 石油工業 名詞術語 第99部分:總則和索引 兩種語言版 | Petroleum industry - Terminolgy - Part 99: General and index |
| ISO 20203 | 鋁生產中使用的碳素材料.煅燒焦炭.用X-射線衍射法測定煅燒石油焦的晶體粒度 | Carbonaceous materials used in the production of aluminium - Calcined coke - Determination of crystallite size of calcined petroleum coke by X-ray diffraction |
| ISO 2049 | 石油產品 色度的測定(ASTM等級) | Petroleum products - Determination of colour (ASTM scale) |
| ISO 20623 | 石油及相關產品.用4球法測定流體的極限壓力和耐磨性(歐洲條件) | Petroleum and related products - Determination of the extreme-pressure and anti-wear properties of fluids - Four ball method (European conditions) |
| ISO 20763 | 石油和相關產品.液壓液耐磨性的測定.葉輪泵法 | Petroleum and related products - Determination of anti-wear properties of hydraulic fluids - Vane pump method |
| ISO 20764 | 石油和相關產品.水量測定用高沸點流體試驗區的準備.氮凈化法 | Petroleum and related products - Preparation of a test portion of high-boiling liquids for the determination of water content - Nitrogen purge method |
| ISO 20783-1 | 石油及相關產品.測定抗火液體的乳劑穩定性.第1部分:HFAE類液體 | Petroleum and related products - Determination of emulsion stability of fire-resistant fluids - Part 1: Fluids in category HFAE |
| ISO 20783-2 | 石油及相關產品.測定抗火液體的乳劑穩定性.第2部分:HFB類液體 | Petroleum and related products - Determination of emulsion stability of fire-resistant fluids - Part 2: Fluids in category HFB |
| ISO 20823 | 石油及相關產品.與熱表面接觸時液體易燃性的測定.歧管點火試驗 | Petroleum and related products - Determination of the flammability characteristics of fluids in contact with hot surfaces - Manifold ignition test |
| ISO 20826 | 車載液化石油汽裝置部件.容器 | Automotive LPG components - Containers |
| ISO 20843 | 石油和相關產品.HFAE、HFAS和HFC類別中抗燃液壓油pH值的測定 | Petroleum and related products - Determination of pH of fire-resistant fluids within categories HFAE, HFAS and HFC |
| ISO 20844 | 石油和相關產品.用柴油噴射器噴嘴測定含高聚物油的剪切穩定性 | Petroleum and related products - Determination of the shear stability of polymer-containing oils using a diesel injector nozzle |
| ISO 20846 | 石油制品.機動車燃料的硫含量的測定.紫外線熒光法 | Petroleum products - Determination of sulfur content of automotive fuels - Ultraviolet fluorescence method |
| ISO 20847 | 石油制品.機動車燃料的硫含量的測定.能量分散X射線熒光光譜法 | Petroleum products - Determination of sulfur content of automotive fuels - Energy-dispersive X-ray fluorescence spectrometry |
| ISO 20884 | 石油制品.機動車燃料的硫含量的測定.波長色散X射線熒光光譜法 | Petroleum products - Determination of sulfur content of automotive fuels - Wavelength-dispersive X-ray fluorescence spectrometry |
| ISO 21329 | 石油和天然氣工業.管道運輸系統.機械連接器的試驗過程 | Petroleum and natural gas industries - Pipeline transportation systems - Test procedures for mechanical connectors |
| ISO 2137 | 石油產品 潤滑脂和石油脂 錐入度的測定 | Petroleum products; Lubricating grease and petrolatum; Determination of cone penetration |
| ISO 2160 | 石油產品 對銅的腐蝕性 銅片腐蝕試驗 | Petroleum products - Corrosiveness to copper - Copper strip test |
| ISO 2176 Technical Corrigendum 1 | 石油產品 潤滑脂 滴點的測定 技術勘誤1 | Petroleum products - Lubricating grease - Determination of dropping point; Technical Corrigendum 1 |
| ISO 2176 | 石油產品 潤滑脂 滴點的測定 | Petroleum products - Lubricating grease - Determination of dropping point |
| ISO 22991 | 儲氣瓶.液化石油氣用可運輸?shù)目稍偬畛浜附愉撈?設計和建造 | Gas cylinders - Transportable refillable welded steel cylinders for liquefied petroleum gas (LPG) - Design and construction |
| ISO 23251 Technical Corrigendum 1 | 石油、石化和天然氣工業.壓力釋放和降壓系統.技術勘誤1 | Petroleum, petrochemical and natural gas industries - Pressure-relieving and depressuring systems; Technical Corrigendum 1 |
| ISO 23251 | 石油、石化和天然氣工業.壓力.緩解和減少系統 | Petroleum, petrochemical and natural gas industries - Pressure-relieving and depressuring systems |
| ISO 2909 | 石油產品.用運動粘度計算粘度指數 | Petroleum products - Calculation of viscosity index from kinematic viscosity |
| ISO 2928 | 25巴(2.5MPa)及以下的天然氣和液相或氣相液化石油氣用橡膠軟管和軟管組件.規范 | Rubber hoses and hose assemblies for liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas up to 25 bar (2,5 MPa) - Specification |
| ISO 2977 | 石油產品和烴類溶劑 苯胺點和混合苯胺點的測定 | Petroleum products and hydrocarbon solvents - Determination of aniline point and mixed aniline point |
| ISO 3007 | 石油產品和原油 蒸氣壓的測定 雷德法 | Petroleum products and crude petroleum - Determination of vapour pressure - Reid method |
| ISO 3012 | 石油產品 輕質和中間餾份燃料硫醇硫的測定 電位滴定法 | Petroleum products - Determination of thiol (mercaptan) sulfur in light and middle distillate fuels - Potentiometric method |
| ISO 3013 | 石油產品 航空燃料冰點的測定 | Petroleum products - Determination of the freezing point of aviation fuels |
| ISO 3014 | 石油產品 航空燃料冰點的測定 | Petroleum products; determination of the smoke point of kerosine |
| ISO 3015 | 石油產品 濁點的測定 | Petroleum products; determination of cloud point |
| ISO 3016 | 石油.傾點的測定 | Petroleum products - Determination of pour point |
| ISO 3104 Technical Corrigendum 1 | 石油產品 透明和不透明石油液體 運動粘度的測定和動力粘度的計算 技術勘誤1 | Petroleum products - Transparent and opaque liquids - Determination of kinematic viscosity and calculation of dynamic viscosity; Technical corrigendum 1 |
| ISO 3104 | 石油產品 透明和不透明石油液體 運動粘度的測定和動力粘度的計算 | Petroleum products - Transparent and opaque liquids - Determination of kinematic viscosity and calculation of dynamic viscosity |
| ISO 3170 | 石油液體.人工采樣 | Petroleum liquids - Manual sampling |
| ISO 3171 | 石油液體 自動管線采樣 | Petroleum liquids; automatic pipeline sampling |
| ISO 3183 | 石油和天然氣工業.管道運輸系統用鋼管 | Petroleum and natural gas industries - Steel pipe for pipeline transportation systems |
| ISO 3183-3 Technical Corrigendum 1 | 石油和天然氣工業.管道鋼管.交貨技術條件.第3部分:C級鋼管的要求.技術勘誤1 | Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 3: Pipes of requirement class C; Technical Corrigendum 1 |
| ISO 3405 | 石油產品 常壓下餾份特性的測定 | Petroleum products - Determination of distillation characteristics at atmospheric pressure |
| ISO 3675 | 原油和液體石油產品 密度實驗室測定 密度計法 | Crude petroleum and liquid petroleum products - Laboratory determination of density - Hydrometer method |
| ISO 3733 | 石油產品和瀝青材料 水分的測定 蒸餾法 | Petroleum products and bituminous materials - Determination of water - Distillation method |
| ISO 3734 | 石油產品 燃料油中水和沉積物的測定 離心法 | Petroleum products - Determination of water and sediment in residual fuel oils - Centrifuge method |
| ISO 3771 | 石油產品 總堿值的測定 高氯酸電位滴定法 | Petroleum products - Determination of base number - Perchloric acid potentiometric titration method |
| ISO 3830 | 石油產品 汽油中鉛含量的測定 一氯化碘法 | Petroleum products; determination of lead content of gasoline; iodine monochloride method |
| ISO 3837 Technical Corrigendum 1 | 液體石油產品 烴類的測定 熒光指示劑吸附法 技術勘誤1 | Liquid petroleum products - Determination of hydrocarbon types - Fluorescent indicator adsorption method; Technical Corrigendum 1 |
| ISO 3837 Technical Corrigendum 2 | 液體石油產品 烴類的測定 螢光指示劑吸附法 技術勘誤2 | Liquid petroleum products - Determination of hydrocarbon types - Fluorescent indicator adsorption method; Technical Corrigendum 2 |
| ISO 3837 | 液體石油產品 烴類的測定 熒光指示劑吸附法 | Liquid petroleum products; determination of hydrocarbon types; fluorescent indicator adsorption method |
| ISO 3838 | 原油和液體或固體石油產品.密度或相對密度的測定.毛細管塞比重瓶和帶刻度雙毛細管比重瓶法 | Crude petroleum and liquid or solid petroleum products - Determination of density or relative density - Capillary-stoppered pyknometer and graduated bicapillary pyknometer methods |
| ISO 3839 | 石油產品 餾份和脂肪族烯烴溴值的測定 電位滴定法 | Petroleum products - Determination of bromine number of distillates and aliphatic olefins - Electrometric method |
| ISO 3871 | 道路車輛 石油基或非石油基制動液容器的標記 | Road vehicles - Labelling of containers for petroleum or non-petroleum base brake fluid |
| ISO 3924 | 石油產品 餾程的測定 氣相色譜法 | Petroleum products - Determination of boiling range distribution - Gas chromatography method |
| ISO 3962 | 石油和天然氣工業用材料和設備.油井或天然氣井用鋼鉆桿的鉆具接頭 | Materials and equipment for petroleum and natural gas industries; Tool joints for steel drill pipe for oil or natural gas wells |
| ISO 3977-5 | 燃?xì)廨啓C(jī) 采購 第5部分：在石油和天然氣工業中的應用 | Gas turbines - Procurement - Part 5: Applications for petroleum and natural gas industries |
| ISO 3987 | 石油產品 潤滑油和添加劑 硫酸鹽灰分的測定 | Petroleum products - Lubricating oils and additives - Determination of sulfated ash |
| ISO 3993 | 液化石油氣和輕質烴類 密度或相對密度的測定 壓力比重計法 | Liquefied petroleum gas and light hydrocarbons; Determination of density or relative density; Pressure hydrometer method |
| ISO 3996 | 道路車輛 使用非石油基制動液的液壓制動系統軟管組件 | Road vehicles - Brake hose assemblies for hydraulic braking systems used with non-petroleum-base brake fluid |
| ISO 4256 | 液化石油氣 蒸氣壓的測定 LPG法 | Liquefied petroleum gases - Determination of gauge vapour pressure - LPG method |
| ISO 4257 Technical Corrigendum 1 | 液化石油氣.取樣方法.技術勘誤1 | Liquefied petroleum gases - Method of sampling; Technical Corrigendum 1 |
| ISO 4257 | 液化石油氣 采樣方法 | Liquefied petroleum gases - Method of sampling |
| ISO 4259 | 石油產品.與試驗方法相關的精度數據的確定和應用 | Petroleum products - Determination and application of precision data in relation to methods of test |
| ISO 4260 | 石油產品和烴類 硫含量的測定 威克波耳德(Wickbold)燃燒法 | Petroleum products and hydrocarbons; Determination of sulfur content; Wickbold combustion method |
| ISO 4261 | 石油產品 燃料(F類) 船和工業用燃?xì)廨啓C(jī)燃料的規格 | Petroleum products; fuels (class F); specifications of gas turbine fuels for industrial and marine applications |
| ISO 4262 | 石油產品 殘?zhí)嫉臏y(cè)定 蘭姆斯波特姆(Ramsbottom)法(簡稱“蘭氏法”) | Petroleum products; determination of carbon residue; Ramsbottom method |
| ISO 4263-1 | 石油及相關產品.防腐蝕礦物油和液體老化性的測定.TOST試驗.第1部分:礦物油測定規程 | Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids; TOST test - Part 1: Procedure for mineral oils |
| ISO 4263-2 | 石油及相關產品.防腐蝕礦物油和液體老化性的測定.TOST試驗.第2部分:HFC類液壓液測定規程 | Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids; TOST test - Part 2: Procedure for category HFC hydraulic fluids |
| ISO 4263-3 | 石油及相關產品.防腐蝕礦物油和液體老化性的測定.TOST試驗.第2部分:合成液壓液的無水程序 | Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test - Part 3: Anhydrous procedure for synthetic hydraulic fluids |
| ISO 4263-4 | 石油及相關產品.防腐蝕礦物油和液體的老化性能測定.TOST試驗.第4部分:工業齒輪油的程序 | Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test - Part 4: Procedure for industrial gear oils |
| ISO 4264 | 石油產品.四變量公式法計算中間餾分燃料的十六烷指數 | Petroleum products - Calculation of cetane index of middle-distillate fuels by the four-variable equation |
| ISO 4266-1 | 石油和液態石油產品.用自動法測定儲罐中溫度和液面.第1部分:氣罐的液面測量 | Petroleum and liquid petroleum products - Measurement of level and temperature in storage tanks by automatic methods - Part 1: Measurement of level in atmospheric tanks |
| ISO 4266-2 | 石油和液態石油產品.用自動法測定儲罐中溫度和液面.第2部分:船用容器的液面測量 | Petroleum and liquid petroleum products - Measurement of level and temperature in storage tanks by automatic methods - Part 2: Measurement of level in marine vessels |
| ISO 4266-3 | 石油和液態石油產品.用自動法測定儲罐中溫度和液面.第3部分:加壓儲罐的液面測量(非冷卻的) | Petroleum and liquid petroleum products - Measurement of level and temperature in storage tanks by automatic methods - Part 3: Measurement of level in pressurized storage tanks (non-refrigerated) |
| ISO 4266-4 | 石油和液態石油產品.用自動法測定儲罐中溫度和液面.第4部分:氣罐溫度的測量 | Petroleum and liquid petroleum products - Measurement of level and temperature in storage tanks by automatic methods - Part 4: Measurement of temperature in atmospheric tanks |
| ISO 4266-5 | 石油和液態石油產品.用自動法測定儲罐中溫度和液面.第5部分:船用容器溫度的測量 | Petroleum and liquid petroleum products - Measurement of level and temperature in storage tanks by automatic methods - Part 5: Measurement of temperature in marine vessels |
| ISO 4266-6 | 石油和液態石油產品.用自動法測定儲罐中溫度和液面.第6部分:加壓儲罐溫度的測量(非冷卻的) | Petroleum and liquid petroleum products - Measurement of level and temperature in storage tanks by automatic methods - Part 6: Measurement of temperature in pressurized storage tanks (non-refrigerated) |
| ISO 4267-2 | 石油和液態石油產品 油量的估算 第2部分:動態計量 | Petroleum and liquid petroleum products; calculation of oil quantities; part 2: dynamic measurement |
| ISO 4268 | 石油和液態石油產品 溫度計量 手工法 | Petroleum and liquid petroleum products - Temperature measurements - Manual methods |
| ISO 4269 | 石油和液態石油產品 采用液態測量的油罐標定 采用容量計的增量法 | Petroleum and liquid petroleum products - Tank calibration by liquid measurement - Incremental method using volumetric meters |
| ISO 4404-1 | 石油及有關產品 耐火液壓油液的抗腐蝕性的測定 第1部分：含水油液 | Petroleum and related products - Determination of the corrosion resistance of fire-resistant hydraulic fluids - Part 1: Water-containing fluids |
| ISO 4404-2 | 石油和相關產品.難燃液壓液抗腐蝕性的測定.第2部分:不含水油液 | Petroleum and related products - Determination of the corrosion resistance of fire-resistant hydraulic fluids - Part 2: Non-aqueous fluids |
| ISO 4512 | 石油和液態石油產品 儲油罐中液位的測量設備 人工法 | Petroleum and liquid petroleum products - Equipment for measurement of liquid levels in storage tanks - Manual methods |
| ISO 4925 | 道路車輛.液壓系統用非石油基制動液的規范 | Road vehicles - Specification of non-petroleum-base brake fluids for hydraulic systems |
| ISO 4926 | 道路車輛.液壓制動系統.非石油基基準液 | Road vehicles - Hydraulic braking systems - Non-petroleum-base reference fluids |
| ISO 4927 | 道路車輛.使用非石油基液壓制動液的鼓式液壓制動輪缸的彈性保護罩(最高工作溫度120℃) | Road vehicles - Elastomeric boots for cylinders for drum type hydraulic brake wheel cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120 °C max.) |
| ISO 4928 | 道路車輛.使用非石油基液壓制動液的液壓制動系統液壓缸的彈性皮碗和密封圈(最高工作溫度120℃) | Road vehicles - Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (Service temperature 120 °C max.) |
| ISO 4929 | 道路車輛 使用非石油基液壓制動液的液壓制動主液壓缸儲油器的膜片密封墊 | Road vehicles; Diaphragm gaskets for hydraulic brake master cylinder reservoirs using a non-petroleum base hydraulic brake fluid |
| ISO 4930 | 道路車輛.使用非石油基液壓制動液的液壓制動盤式液壓缸的彈性密封墊(最高工作溫度150℃) | Road vehicles - Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 150° C max.) |
| ISO 5024 | 石油液體和液化石油氣 計量 標準參考條件 | Petroleum liquids and liquefied petroleum gases - Measurement - Standard reference conditions |
| ISO 5163 | 石油產品.發動機和航空燃料爆震特性的測定.馬達法 | Petroleum products - Determination of knock characteristics of motor and aviation fuels - Motor method |
| ISO 5164 | 石油產品.發動機燃料爆震特性的測定.研究法 | Petroleum products - Determination of knock characteristics of motor fuels - Research method |
| ISO 5165 | 石油產品 柴油著火性能的測定 十六烷值法 | Petroleum products - Determination of the ignition quality of diesel fuels - Cetane engine method |
| ISO 5226 | 石油和天然氣工業用材料和設備.油井或天然氣井用鋁合金鉆管 | Materials and equipment for petroleum and natural gas industries; Aluminium alloy drill pipe for oil or natural gas wells |
| ISO 5275 | 石油產品和烴類溶劑.硫醇類和其他硫類的測定.(博士法試驗-定硫醇) | Petroleum products and hydrocarbon solvents - Detection of thiols and other sulfur species - Doctor test |
| ISO 5661 | 石油產品 液態烴類 折光指數的測定 | Petroleum products; Hydrocarbon liquids; Determination of refractive index |
| ISO 6117 | 道路車輛.使用非石油基液壓制動液的鼓式液壓制動輪缸的彈性保護罩(最高工作溫度100℃) | Road vehicles - Elastomeric boots for drum-type, hydraulic brake wheel cylinders using a non-petroleum base hydraulic brake fluid (service temperature 100 °C max.) |
| ISO 6118 | 道路車輛.使用非石油基制動液的液壓制動促動缸的彈性皮碗和密封圈(最高工作溫度70℃) | Road vehicles - Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (service temperature 70 °C max.) |
| ISO 6119 | 道路車輛.使用非石油基液壓制動液的液壓盤式制動液壓缸的彈性密封墊(最高工作溫度120℃) | Road vehicles - Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120 °C max.) |
| ISO 6120 | 道路車輛.使用石油基液壓液的液壓制動系統制動軟管總成 | Road vehicles - Brake hose assemblies for hydraulic braking systems used with petroleum-base brake fluid |
| ISO 6244 | 石蠟和石油脂 滴熔點的測定 | Petroleum waxes and petrolatums; Determination of drop melting point |
| ISO 6245 | 石油制品 灰分測定 | Petroleum products - Determination of ash |
| ISO 6246 Technical Corrigendum 1 | 石油產品 輕質和中間餾份燃料的膠含量 噴射蒸發法 技術勘誤1 | Petroleum products - Gum content of light and middle distillate fuels - Jet evaporation method; Technical Corrigendum 1 |
| ISO 6246 | 石油產品 輕質和中間餾份燃料的膠含量 噴射蒸發法 | Petroleum products - Gum content of light and middle distillate fuels - Jet evaporation method |
| ISO 6247 Technical Corrigendum 1 | 石油產品 潤滑油發泡特性的測定 技術勘誤1 | Petroleum products - Determination of foaming characteristics of lubricating oils; Technical Corrigendum 1 |
| ISO 6247 | 石油產品 潤滑油發泡特性的測定 | Petroleum products - Determination of foaming characteristics of lubricating oils |
| ISO 6249 | 石油產品 燃?xì)廨啓C(jī)燃料熱氧化安定性的測定 JFTOT法 | Petroleum products - Determination of thermal oxidation stability of gas turbine fuels - JFTOT method |
| ISO 6250 | 石油產品 航空燃料水反應的測定 | Petroleum products - Determination of the water reaction of aviation fuels |
| ISO 6251 | 液化石油氣 對銅的腐蝕性 銅片試驗 | Liquefied petroleum gases - Corrosiveness to copper - Copper strip test |
| ISO 6293-1 | 石油產品 皂化值的測定 第1部分:顏色指示滴定法 | Petroleum products - Determination of saponification number - Part 1: Colour indicator titration method |
| ISO 6293-2 | 石油產品 皂化值的測定 第2部分:電位滴定法 | Petroleum products - Determination of saponification number - Part 2: Potentiometric titration method |
| ISO 6296 | 石油產品 水的測定 電位測量卡爾·費休滴定法 | Petroleum products - Determination of water - Potentiometric Karl Fischer titration method |
| ISO 6297 | 石油產品 航空和餾份燃料 電導率的測定 | Petroleum products - Aviation and distillate fuels - Determination of electrical conductivity |
| ISO 6299 | 石油產品 潤滑脂滴點(寬溫度范圍)的測定 | Petroleum products - Determination of dropping point of lubricating greases (wide temperature range) |
| ISO 6448 | 橡膠密封件 輸送石油產品管道和配件用密封圈 材料規范 | Rubber seals; Joint rings used for petroleum product supply pipes and fittings; Specification for material |
| ISO 6551 | 石油液體和氣體 動態測量的精度和可靠性 電脈沖數據和/或電子脈沖數據的電纜傳輸 | Petroleum liquids and gases; Fidelity and security of dynamic measurement; Cabled transmission of electric and/or electronic pulsed data |
| ISO 6614 | 石油產品 礦物油和合成液水分離的測定 | Petroleum products - Determination of water separability of petroleum oils and synthetic fluids |
| ISO 6615 | 石油產品 殘?zhí)嫉臏y(cè)定 康氏法 | Petroleum products; determination of carbon residue; Conradson method |
| ISO 6617 | 石油基潤滑油 老化特性 氧化后殘?zhí)甲兓臏y(cè)定 | Petroleum-based lubricating oils - Ageing characteristics - Determination of change in Conradson carbon residue after oxidation |
| ISO 6618 Technical Corrigendum 1 | 石油產品和潤滑劑.酸和中和堿值的測定.顏色指示劑滴定法.技術勘誤1 | Petroleum products and lubricants - Determination of acid or base number - Coulour-indicator titration method; Technical Corrigendum 1 |
| ISO 6618 | 石油產品和潤滑劑 酸和中和堿值的測定 顏色指示劑滴定法 | Petroleum products and lubricants - Determination of acid or base number - Coulour-indicator titration method |
| ISO 6619 | 石油產品和潤滑劑 中和值 電位滴定法 | Petroleum products and lubricants; neutralization number; potentiometric titration method |
| ISO 7120 | 石油產品和潤滑劑 石油原油和其他液體 水存在時防銹性能的測定 | Petroleum products and lubricants; Petroleum oils and other fluids; Determination of rust-preventing characteristics in the presence of water |
| ISO 7308 | 道路車輛 儲能液壓制動用的石油基制動液 | Road vehicles; Petroleum-based brake-fluid for stored-energy hydraulic brakes |
| ISO 7309 | 道路車輛 液壓制動系統 ISO標準石油基液 | Road vehicles; Hydraulic braking systems; ISO reference petroleum base fluid |
| ISO 734-1 | 油料種子殘?jiān)?測定油含量.第1部分:已烷萃取法(輕質石油) | Oilseed meals - Determination of oil content - Part 1: Extraction method with hexane (or light petroleum) |
| ISO 7507-1 | 石油和液態石油產品.直立式圓筒狀油罐的標定.第1部分:圍測法 | Petroleum and liquid petroleum products - Calibration of vertical cylindrical tanks - Part 1: Strapping method |
| ISO 7507-2 | 石油和液態石油產品.直立式圓筒狀油罐的標定.第2部分:光學參比線法 | Petroleum and liquid petroleum products - Calibration of vertical cylindrical tanks - Part 2: Optical-reference-line method |
| ISO 7507-3 | 石油和液態石油產品.直立式圓筒狀油罐的標定.第3部分:光學三角測量法 | Petroleum and liquid petroleum products - Calibration of vertical cylindrical tanks - Part 3: Optical-triangulation method |
| ISO 7507-4 | 石油和液態石油產品 直立式圓筒狀油罐的標定 第4部分:內光電測距法 | Petroleum and liquid petroleum products - Calibration of vertical cylindrical tanks - Part 4: Internal electro-optical distance-ranging method |
| ISO 7507-5 | 石油和液態石油產品 直立式圓筒狀油罐的標定 第5部分:光電外測距法 | Petroleum and liquid petroleum products - Calibration of vertical cylindrical tanks - Part 5: External electro-optical distance-ranging method |
| ISO 7536 | 石油產品 汽油氧化安定性的測定 誘導期法 | Petroleum products - Determination of oxidation stability of gasoline - Induction period method |
| ISO 7537 | 石油產品 總酸值的測定 半微量顏色指示劑滴定法 | Petroleum products - Determination of acid number - Semi-micro colour-indicator titration method |
| ISO 7624 | 石油產品和潤滑劑 加抑制劑礦物汽輪機油 氧化穩定性的測定 | Petroleum products and lubricants - Inhibited mineral turbine oils - Determination of oxidation stability |
| ISO 7630 | 道路車輛 使用石油基液壓制動液的鼓式制動輪缸的彈性O(shè)形密封圈(最高工作溫度120℃) | Road vehicles; Elastomeric O-rings for hydraulic drum brake wheel cylinders using a petroleum base hydraulic brake fluid (service temperature 120 degrees C max.) |
| ISO 7631 | 道路車輛 使用石油基液壓制動液的液壓制動系統液壓缸的彈性皮碗和密封墊圈(最高工作溫度120℃) | Road vehicles; Elastomeric cups and seals for cylinders for hydraulic braking systems using a petroleum base hydraulic brake fluid (service temperature 120 degrees C max.) |
| ISO 7632 | 道路車輛 使用石油基液壓制動液的液壓盤式制動液壓缸的彈性密封墊圈(最高工作溫度120℃) | Road vehicles; Elastomeric seals for hydraulic disc brake cylinders using a petroleum base hydraulic brake fluid (service temperature 120 degrees C max.) |
| ISO 7633 | 道路車輛 使用石油基液壓制動液的鼓式液壓制動輪缸的彈性保護罩(最高工作溫度120℃) | Road vehicles; Elastomeric boots for drum type hydraulic brake wheel cylinders using a petroleum base hydraulic brake fluid (service temperature 120 degrees C max.) |
| ISO 8216-1 | 石油產品.燃料(F類)分類.第1部分:船用燃料類別 | Petroleum products - Fuels (class F) classification - Part 1: Categories of marine fuels |
| ISO 8216-2 | 石油產品 燃料(F類) 分類 第2部分:工業和船用燃?xì)廨啓C(jī)燃料的種類 | Petroleum products; Fuels (class F); Classification; Part 2 : Categories of gas turbine fuels for industrial and marine applications |
| ISO 8216-3 | 石油產品 燃料(F類) 分類 第3部分:L組(液化石油氣) | Petroleum products; Fuels (class F); Classification; Part 3 : Family L (Liquefied petroleum gases) |
| ISO 8216-99 | 石油產品.燃料(F類).分類.第99部分:總則 | Petroleum products - Fuels (class F); Classification - Part 99: General |
| ISO 8217 | 石油產品.燃料(F類).船用燃料規范 | Petroleum products - Fuels (class F) - Specifications of marine fuels |
| ISO 8222 | 石油測量系統.校準.容積驗證箱校正時的溫度修正 | Petroleum measurement systems - Calibration - Temperature corrections for use when calibrating volumetric proving tanks |
| ISO 8681 | 石油產品和潤滑劑 分類法 等級的定義 | Petroleum products and lubricants; Method of classification; Definition of classes |
| ISO 8691 | 石油產品 液體燃料中的微量釩 用灰化后火焰原子吸收光譜法測定 | Petroleum products - Low levels of vanadium in liquid fuels - Determination by flameless atomic absorption spectrometry after ashing |
| ISO 8697 | 原油和石油產品 運輸量估算 船上質量(OBQ)和船上剩余量(ROB)的評估 | Crude petroleum and petroleum products - Transfer accountability - Assessment of on board quantity (OBQ) and quantity remaining on board (ROB) |
| ISO 8754 | 石油產品.硫含量的測定.能量分散X射線熒光光譜測定法 | Petroleum products - Determination of sulfur content - Energy-dispersive X-ray fluorescence spectrometry |
| ISO 8789 | 摩托車輸送液化石油氣用橡膠軟管和軟管組件 規范 | Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles - Specification |
| ISO 8819 | 液化石油氣 硫化氫的測定 乙酸鉛法 | Liquefied petroleum gases; detection of hydrogen sulfide; lead acetate method |
| ISO 8973 | 液化石油氣 密度和蒸氣壓的計算 | Liquefied petroleum gases - Calculation for density and vapour pressure |
| ISO 91-1 | 石油計量表.第1部分:以15鳦和60鳩為參比溫度基礎的表 | Petroleum measurement tables; part 1: tables based on reference temperatures of 15 °C and 60 °F |
| ISO 91-2 | 石油計量表.第2部分:以20℃為參比溫度基礎的表 | Petroleum measurement tables; part 2: tables based on a reference temperature of 20 °C |
| ISO 9120 | 石油及相關產品.汽輪機油和其他油的空氣釋放性能的測定.沖擊濾塵器法 | Petroleum and related products - Determination of air-release properties of steam turbine and other oils - Impinger method |
| ISO 9162 | 石油產品 燃料(F類) 液化石油氣 規格 | Petroleum products; fuels (class F); liquefied petroleum gases; specifications |
| ISO 9200 | 原油和液態石油產品 粘質烴類容量計量 | Crude petroleum and liquid petroleum products; volumetric metering of viscous hydrocarbons |
| ISO 9770 | 石油和石油產品 碳?xì)浠衔镌?38kg/m-1074kg/m的壓縮因數 | Crude petroleum and petroleum products; compressibility factors for hydrocarbons in the range 638 kg/m<(hoch)3> to 1074 kg/m<(hoch)3> |
| ISO/TR 13739 | 石油產品 制定向船用燃料艙輸送燃料的實用程序的方法 | Petroleum products - Methods for specifying practical procedures for the transfer of bunker fuels to ships |
| ISO/TR 13881 | 石油和天然氣工業 產品、加工和服務的分類和合格評定 | Petroleum and natural gas industries - Classification and conformity assessment of products, processes and services |
| ISO/TS 15926-4 | 工業自動化系統和集成.包括石油和天然氣生產設施的加工設備使用壽命數據的集成.第4部分:原始參考數據 | Industrial automation systems and integration - Integration of life-cycle data for process plants including oil and gas production facilities - Part 4: Initial reference data |
| ISO/TS 24817 | 石油、石化和天然氣工業.管件用復合材料檢修. 資格鑒定和設計、安裝、試驗和檢驗 | Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection |
| ISO/TS 29001 | 石油、化工和天然氣工業.部門專用質量管理系統.產品和服務機構的要求 | Petroleum, petrochemical and natural gas industries - Sector-specific quality management systems - Requirements for product and service supply organizations |
| 編號 | 中文名稱 | 英文名稱 |