微信掃一掃，立即回復！
| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| JIS A1439 | 建筑物中密封和門窗玻璃用密封劑的試驗方法 | Testing methods of sealants for sealing and glazing in buildings |
| JIS A1470-2 | 調節室內濕度的建筑材料的吸濕或脫濕的試驗方法.第2部分:密封箱法 | Test method of adsorption/desorption efficiency for building materials to regulate an indoor humidity -- Part 2: Sealed box method |
| JIS A5750 | 建筑物中門窗和面板接縫用彈性泡沫預制密封墊 | Elastomeric cellular preformed gaskets for windows, doors and joints of panel in buildings |
| JIS A5756 AMD 1 | 建筑襯墊和建筑結構襯墊.門窗玻璃安裝和嵌板密封用預成形固態硫化橡膠材料（修改件1） | Building gaskets and Building structural gaskets -- Materials in preformed solid vulcanizates used for sealing glazing and panels (Amendment 1) |
| JIS A5756 | 建筑襯墊和建筑結構襯墊.門窗玻璃安裝和嵌板密封用預成形固態硫化橡膠材料 | Building gaskets and Building structural gaskets -- Materials in preformed solid vulcanizates used for sealing glazing and panels |
| JIS A5758 | 建筑物中密封和門窗玻璃用密封劑 | Sealants for sealing and glazing in buildings |
| JIS B0116 | 包裝材料和密封墊術語匯編 | Glossary of terms for packings and gaskets |
| JIS B2207 AMD 1 | 具有全密封墊鋁合金管法蘭的計算基礎(修改件1) | Basis for calculation of aluminium alloy pipe flanges with full face gasket (Amendment 1) |
| JIS B2355-1 | 流體動力用和通用的連接件.帶ISO261螺紋和 O 形環密封件的端口和螺柱端頭.第1部分:截斷平頭殼體內帶有 O 形 | Connections for fluid power and general use -- Ports and stud ends with ISO 261 threads and O-ring sealing -- Part 1: Ports with O-ring seal in truncated housing |
| JIS B2355-2 | 流體動力用和通用連接件.帶ISO261螺紋和 O 形環密封件的端口和螺柱端頭.第2部分:大功能（S系列）螺柱端頭. | Connections for fluid power and general use -- Ports and stud ends with ISO 261 threads and O-ring sealing -- Part 2: Heavy-duty (S series) stud ends -- Dimensions, design, test methods and requirements |
| JIS B2355-3 | 流體動力用和通用連接件.帶ISO261螺紋和 O 形環密封件的端口和螺柱端頭.第3部分:小功能（L 系列）螺柱端頭. | Connections for fluid power and general use -- Ports and stud ends with ISO 261 threads and O-ring sealing -- Part 3: Light-duty (L series) stud ends -- Dimensions, design, test methods and requirements |
| JIS B2356-1 | 一般用途的和流體動力用接頭.帶彈性密封件或金屬與金屬間密封件的ISO 261螺紋的端口和螺柱端頭.第1部分:螺 | Connections for general use and fluid power -- Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing -- Part 1: Threaded ports |
| JIS B2356-2 | 流體動力用和通用連接件.帶ISO 261螺紋，帶有彈性體或金屬對金屬密封件的端口和螺柱斷頭.第2部分:帶彈性密 | Connections for general use and fluid power -- Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing -- Part 2: Stud ends with elastomeric sealing (type E) |
| JIS B2358-1 | 一般用途的和流體動力用接頭.帶ISO 261螺紋和O形環密封件的端口和螺柱端頭.第1部分:在截斷外殼體內裝有O形 | Connections for general use and fluid power -- Ports and stud ends with ISO 725 threads and O-ring sealing -- Part 1: Ports with O-ring seal in truncated housing |
| JIS B2402-1 | 旋轉軸唇形密封件.第1部分:公稱尺寸和公差 オイルシール ― 第１部：寸法及び許容差 | Rotary shaft lip type seals -- Part 1: Nominal dimensions and tolerances |
| JIS B2402-2 | 旋轉軸唇形密封件.第2部分:詞匯 オイルシール ― 第２部：用語 | Rotary shaft lip type seals -- Part 2: Vocabulary |
| JIS B2402-3 | 旋轉軸唇形密封件.第3部分:儲存、搬運和安裝 オイルシール ― 第３部：保管，取扱い及び取付 | Rotary shaft lip type seals -- Part 3: Storage, handling and installation |
| JIS B2402-4 | 旋轉軸唇形密封件.第4部分:性能試驗程序 オイルシール ― 第４部：性能試験方法 | Rotary shaft lip type seals -- Part 4: Performance test procedures |
| JIS B2402-5 | 旋轉軸唇形密封件.第5部分:目視缺陷的鑒定 オイルシール ― 第５部：外観欠陥 | Rotary shaft lip type seals -- Part 5: Identification of visual imperfections |
| JIS B2403 | V型密封件 Ｖパッキン | V packings |
| JIS B2405 | 機械密封件.一般要求 メカニカルシール通則 | Mechanical seals -- General requirements |
| JIS B2405 AMD 1 | 機械密封.通用要求(修改件1) メカニカルシール通則（追補１） | Mechanical seals -- General requirements (Amendment 1) |
| JIS B2406 | O形密封圈裝配槽.設計標準 Ｏリング取付溝部の形狀?寸法 | O-rings housings -- Design criteria |
| JIS B2407 | O型密封圈的保護墊圈 Ｏリング用バックアップリング | Back-up rings for O-rings |
| JIS B2409 | 液壓流體動力.密封裝置.油壓往復設備的密封件性能評定的標準試驗方法 油圧 ― 密封裝置 ― 油圧用往復動シールの性能評価標準試験方法 | Hydraulic fluid power -- Sealing devices -- Standard test methods to assess the performance of seals used in oil hydraulic reciprocating applications |
| JIS B2410 | O型密封圈.工業用彈性材料的適宜性 Ｏリング－ゴム材料の選定指針 | O-rings -- Suitability of elastomeric materials for industrial applications |
| JIS B8367-2 | 液壓氣缸的安裝尺寸.第2部分:單桿.16 MPa系列、方蓋、系桿密封型液壓氣缸(氣缸內徑25 mm 至 200 mm) | Mounting dimensions for hydraulic cylinders -- Part 2: Single rod -- 16 MPa series, square cover and tie rod tightend type (Bores from 25 mm to 200 mm) |
| JIS B8367-3 | 液壓氣缸的安裝尺寸.第3部分:單桿.16 MPa系列、方蓋、系桿密封型液壓氣缸(氣缸內徑250 mm 至 500 mm) | Mounting dimensions for hydraulic cylinders -- Part 3: Single rod -- 16 MPa series, square cover and tie rod tightend type (Bores from 250 mm to 500 mm) |
| JIS B8367-5 | 液壓氣缸的安裝尺寸.第5部分:單桿.10 MPa系列、方蓋、系桿密封型液壓氣缸(汽缸內徑40 mm 至 200 mm) | Mounting dimensions for hydraulic cylinders -- Part 5: Single rod -- 10 MPa series, square cover and tie rod tightend type (Bores from 40 mm to 200 mm) |
| JIS B8368-1 | 氣壓缸的安裝尺寸.第1部分:單桿.帶固定安裝裝置的1 MPa系列、方蓋、系桿密封型液壓氣缸(汽缸內徑32 mm 至 2 | Mounting dimensions for pneumatic cylinders -- Part 1: Single rod -- 1 MPa series, square cover and tie rod tightend type with fixed mounting devices (Bores from 32 mm to 250 mm) |
| JIS B8368-2 | 氣壓缸的安裝尺寸.第2部分:單桿.帶可分離安裝裝置的1 MPa系列、方蓋、系桿密封型液壓氣缸(汽缸內徑32 mm 至 | Mounting dimensions for pneumatic cylinders -- Part 2: Single rod -- 1 MPa series, square cover and tie rod tightend type with detachable mounting devices (Bores from 32 mm to 320 mm) |
| JIS B8394-1 | 液壓動力.彈性體增能用、塑料面密封液壓缸.尺寸和公差.第1部分:活塞密封液壓缸 | Hydraulic fluid power -- Housings for elastomer-energized, plastic-faced seals -- Dimensions and tolerances -- Part 1: Piston seal housings |
| JIS B8394-2 | 液壓動力.彈性體增能用、塑料面密封液壓缸.尺寸和公差.第2部分:桿密封液壓缸 | Hydraulic fluid power -- Housings for elastomer-energized, plastic-faced seals -- Dimensions and tolerances -- Part 2: Rod seal housings |
| JIS B8396 | 流體動力系統和元件.氣缸.往復運功用的活塞和活塞桿密封件的外套.尺寸和公差 | Hydraulic fluid power -- Cylinders -- Housings for piston and rod seals in reciprocating applications -- Dimensions and tolerances |
| JIS C4306 | 6kV密封繞組式配電變壓器 | 6kV Encapsulated-winding distribution transformers |
| JIS C5402-12-6 | 電子設備連接器.試驗和測量.第12-6部分:釬焊試驗.試驗12f:機器釬焊時連接件密封耐焊劑和清洗劑性能 | Connectors for electronic equipment -- Tests and measurements -- Part 12-6: Soldering tests -- Test 12f: Sealing against flux and cleaning solvents in machine soldering |
| JIS C5402-14-7 | 電子設備連接器.試驗和測量.第14-7部分:密封試驗.試驗14g:水沖擊試驗 | Connectors for electronic equipment -- Tests and measurements -- Part 14-7: Sealing tests -- Test 14g: Impacting water |
| JIS C60068-2-17 | 基本環境試驗過程.第2部分:試驗.試驗Q:密封 | Basic environmental testing procedures -- Part 2: Tests -- Test Q: Sealing |
| JIS C8705 | 密封可再充電式鎳鎘單電池 | Sealed nickel-cadmium rechargeable single cells |
| JIS C8712 | 便攜設備用便攜式密封二次電池及由其制成的蓄電池的安全要求 | Safety requirements for portable sealed secondary cells, and batteries made from them, for use in portable applications |
| JIS C8713 | 包括堿性或其他非酸性電解液的二次電池和蓄電池.密封便攜式二次電池和蓄電池的機械試驗 | Secondary cells and batteries containing alkaline or other non-acid electrolytes -- Mechanical tests for sealed portable secondary cells and batteries |
| JIS C9730-2-4 | 家用和類似用途的自動電氣控制裝置.第2-4部分:密封和半密封型電動壓縮機用熱電機保護器的特殊要求 | Automatic electrical controls for household and similar use -- Part 2-4: Particular requirements for thermal motor protectors for motor-compressors of hermetic and semi-hermetic type |
| JIS D2609 | 道路車輛.使用非石油基液壓制動液的液壓盤式制動缸的彈性密封件 | Road vehicles -- Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid |
| JIS D2612 | 汽車部件.使用非石油基液壓制動液的液壓制動主油缸用儲油箱密封件 | Automotive parts -- Reservoir seals for hydraulic brake master cylinders using a non-petroleum base hydraulic brake fluid |
| JIS D3105 | 汽車發動機用氣缸蓋密封墊 | Cylinder head gaskets for automobile engines |
| JIS F8801 | 造船.電氣設備用防水電纜密封套 | Shipbuilding -- Watertight cable glands for electric appliance |
| JIS F8802 | 船舶艙壁和甲板用電纜密封套 | Marine cable glands for bulkhead and deck |
| JIS F8838 | 造船.防水密封插頭和插座盒 | Shipbuilding -- Watertight type plugs and socket-outlet boxes |
| JIS H8683-1 | 鋁及鋁合金陽極氧化覆層密封質量試驗方法.第1部分:染料點滴試驗方法 | Test methods for sealing quality of anodic oxide coatings on aluminium and aluminium alloys -- Part 1: Dye spot test method |
| JIS H8683-2 | 鋁及鋁合金陽極氧化覆層密封質量試驗方法.第2部分:磷鉻酸溶液浸入的試驗方法 | Test methods for sealing quality of anodic oxide coatings on aluminium and aluminium alloys -- Part 2: Phosphoric-chromic acid solution immersion test method |
| JIS H8683-3 | 鋁及鋁合金陽極氧化覆層密封質量試驗方法.第3部分:導納試驗方法 | Test methods for sealing quality of anodic oxide coatings on aluminium and aluminium alloys -- Part 3: Admittance test method |
| JIS K5533 | 天然漆密封劑 | Lacquer sealers |
| JIS K5663 | 合成樹脂乳膠漆和密封劑 | Synthetic resin emulsion paint and sealer |
| JIS K6380 | 橡膠密封材料 | Rubber packing material |
| JIS K6820 AMD 1 | 液體密封劑（修改件1） | Fluid sealants (Amendment 1) |
| JIS K6820 | 液體密封劑 | Fluid sealants |
| JIS K6885 | 螺紋密封用未燒結聚四氟乙烯帶 | Unsintered polytetrafluoroethylene tapes for thread sealing |
| JIS K7031 | 塑料管道系統.玻璃纖維增強熱固性塑料(GRP)管道和配件.在短期內壓下管壁密封性檢定的試驗方法 | Plastics piping systems -- Glass-reinforced thermosetting plastics (GRP) pipes and fittings -- Test methods to prove the leaktightness of the wall under short-term internal pressure |
| JIS R3209 | 密封絕緣玻璃 | Sealed insulating glass |
| JIS S2031 | 密封型燃油空間加熱器 | Closed type oil burning space heaters |
| JIS S6020 | 朱砂密封墨盒 | SHUNIKU (Cinnabar seal-ink pads) |
| JIS T6522 | 牙根管密封材料 | Dental root canal sealing materials |
| JIS T6524 | 牙科.聚合凹紋和裂紋密封劑 | Dentistry -- Polymer-based pit and fissure sealants |
| JIS W1831 | 航空航天.流體系統用帶螺紋的和密封的聯結件.尺寸 | Aerospace -- Couplings, threaded and sealed, for fluid systems -- Dimensions |
| JIS W2014 | 航空航天系統保護用涂飾劑、涂漆及密封劑 | Finishes, coatings and sealants for the protection of aerospace systems |
| JIS Z1571 | 食品和飲料用密封金屬罐 | Hermetically sealed metal cans for food and drink |
| JIS Z4821-1 | 密封放射源.一般要求和分類 | Sealed radioactive sources -- General requirements and classification |
| JIS Z4821-2 | 密封放射源.漏泄試驗方法 | Sealed radioactive sources -- Leakage test methods |
| JIS Z7302-10 | 密封垃圾再生燃料.第10部分:分解物的測試方法 | Densified refuse derived fuel -- Part 10: Test method for disintegrated contents |
| JIS Z7302-4 ERRATUM 1 | 密封垃圾的再生燃料.第4部分:灰分的測試方法(勘誤1) | Densified refuse derived fuel -- Part 4: Test method for ash (Erratum 1) |
| JIS Z7302-4 ERRATUM 2 | 密封垃圾的再生燃料.第4部分:灰分的測試方法(勘誤2) | Densified refuse derived fuel -- Part 4: Test method for ash (Erratum 2) |
| JIS Z7302-5 | 密封垃圾再生燃料.第5部分:金屬含量的測試方法 | Densified refuse derived fuel -- Part 5: Test methods of metals contents |
| JIS Z7302-7 | 密封垃圾再生燃料.第7部分:硫含量的測試方法 | Densified refuse derived fuel -- Part 7: Test method for sulfur content |
| JIS Z7302-8 | 密封垃圾再生燃料.第8部分:元素分析的試驗方法 | Densified refuse derived fuel -- Part 8: Test method for ultimate analysis |
| JIS Z7302-9 | 密封垃圾再生燃料.第9部分:表觀體密度的測試方法 | Densified refuse derived fuel -- Part 9: Test method for apparent bulk density |
| 編號 | 中文名稱 | 英文名稱 |