微信掃一掃，立即回復！
| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| EN 10090 | 內燃機閥門用鋼和合金 | Valve steels and alloys for internal combustion engines |
| EN 1074-1 | 供水閥門 目的要求的適應性和合適的認證試驗 第1部分：一般要求 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 1: General requirements |
| EN 1074-2 | 供水閥門 目的要求的適應性和合適的認證試驗 第2部分：絕熱閥門 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 2: Isolating valves |
| EN 1074-3 | 供水閥門 目的要求的適應性和合適的認證試驗 第3部分：檢查閥門 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 3: Check valves |
| EN 1074-4 | 供水閥門 目的要求的適應性和合適的認證試驗 第4部分：氣體閥門 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 4: Air valves |
| EN 1074-5 | 供水閥門 目的要求的適應性和合適的認證試驗 第5部分：控制閥門 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5: Control valves |
| EN 1092-1 | 法蘭及其連接 按PN標注的管、閥門、配件及其附件用圓形法蘭 第1部分：鋼法蘭 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1: Steel flanges |
| EN 1092-2 | 法蘭及其連接 按PN標注的管、閥門、配件及其附件用圓形法蘭 第2部分：鑄鐵法蘭 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| EN 1092-3 | 法蘭及其連接 按PN標注的管、閥門、配件及其附件用圓形法蘭 第3部分：銅合金法蘭 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories PN designated - Part 3: Copper alloy flanges |
| EN 1092-4 | 法蘭及其連接 按PN標注的管、閥門、配件及其附件用圓形法蘭 第4部分：鋁合金法蘭 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4: Aluminium alloy flanges |
| EN 1111 | 衛生水龍頭 溫度調節用混合閥（PN10） 一般技術規范 | Sanitary tapware - Thermostatic mixing valves (PN 10) - General technical specification |
| EN 1171 | 工業閥門 鑄鐵閘門閥 | Industrial valves - Cast iron gate valves |
| EN 12050-4 | 建筑物和施工現場的廢水抽取設備 施工原則和試驗 第4部分：用于含糞便和不含糞便斷線的單向閥 | Wastewater lifting plants for buildings and sites - Principles of construction and testing - Part 4: Non-return valves for faecal-free wastewater and wastewater containing faecal matter |
| EN 12094-13-2001+AC | 固定式消防系統 氣體滅火系統的部件 第13部分：對止回閥和非回流閥的要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 13: Requirements and test methods for check valves and non-return valves |
| EN 12094-5 | 固定式消防系統 氣體滅火系統的部件 第5部分：高、低壓選擇閥及其CO2系統驅動器觸發要求及試驗方法 | Fixed firefighting systems - Components for gas extinguishing systems - Part 5: Requirements and test methods for high and low pressure selector valves and their actuators for CO<(Index)2> systems |
| EN 12100 | 塑料管道系統 聚乙稀(PE)閥門 支架間抗彎曲性的試驗方法 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports |
| EN 12107 | 塑料管道系統 壓注熱塑管件、閥門和輔助設備 管道組件壓注用熱塑 材料的長期液壓強度的測定 | Plastics piping systems - Injection-moulded thermoplastics fittings, valves and ancillary equipment - Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components |
| EN 12117 | 塑料管道系統 熱塑管件、閥門和配件 氣流速率/壓降之間關系的測定 | Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
| EN 12119 | 塑料管道系統 聚乙烯(PE)閥門 抗熱循環測試方法 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling |
| EN 1213 | 建筑物閥門 建筑物內便攜式供水用的銅合金斷流閥 試驗和要求 | Building valves - Copper alloy stopvalves for potable water supply in buildings - Tests and requirements |
| EN 12201-4 | 供水系統用塑料管道系統 聚乙烯（PE） 第4部分：閥門 | Plastics piping systems for water supply - Polyethylene (PE) - Part 4: Valves |
| EN 12259-2 | 固定消防系統 噴水器和噴水系統構件 第2部分：濕式報警閥組件 | Fixed firefighting systems - Components for sprinkler and water spray systems - Part 2: Wet alarm valve assemblies |
| EN 12259-3-2000+A1 | 固定消防系統 噴水器和噴水系統構件 第3部分：干式報警閥組件 | Fixed firefighting systems - Components for sprinkler and water spray systems - Part 3: Dry alarm valve assemblies |
| EN 12266-1 | 工業閥門 閥門試驗 第1部分：壓力試驗、試驗程序和驗收標準、強制要求 | Industrial valves - Testing of valves - Part 1: Pressure tests, test procedures and acceptance criteria; Mandatory requirements |
| EN 12266-2 | 工業閥門 閥門試驗 第2部分：試驗、試驗程序和驗收標準 補充要求 | Industrial valves - Testing of valves - Part 2: Tests, test procedures and acceptance criteria; Supplementary requirements |
| EN 12284 | 制冷系統和加熱泵 閥門 要求、試驗和標志 | Refrigerating systems and heat pumps - Valves - Requirements, testing and marking |
| EN 12288 | 工業用閥 銅合金閘閥 | Industrial valves - Copper alloy gate valves |
| EN 12334 | 工業閥門 鑄鐵止回閥 | Industrial valves - Cast iron check valves |
| EN 12351 | 工業閥門 帶法蘭連接的閥門保護帽 | Industrial valves - Protective caps for valves with flanged connections |
| EN 12380 | 排水系統用進氣閥 要求、試驗方法和合格評定 | Air admittance valves for drainage systems - Requirements, test methods and evaluation of conformity |
| EN 12514-2 | 燃油爐供油系統用的裝置 第２部分：安全要求和試驗 零部件、閥門、管道、濾油器、油氣分離器、油量指示表 | Installations for oil supply systems for oil burners - Part 2: Safety requirements and tests - Parts, valves, pipes, filters, oil de-aerators, meters |
| EN 12516-3-2002+AC | 工業閥門 殼體設計強度 第３部分：試驗方法 | Valves - Shell design strength - Part 3: Experimental method |
| EN 12541 | 衛生間水龍頭 壓力沖洗閥和自動關閉小便池沖洗閥PN10 | Sanitary tapware - Pressure flushing valves und automatic closing urinal valves PN 10 |
| EN 12567 | 工業閥門 LNG隔離閥 適用性規范和適當檢驗測試 | Industrial valves - Isolating valves for LNG - Specification for suitability and appropriate verification tests |
| EN 12569-1999+AC | 工業閥門 化工和石油化學工業用閥門 要求和試驗 | Industrial valves - Valves for chemical and petrochemical process industry - Requirements and tests |
| EN 12570 | 工業閥門 操作元件分級方法 | Industrial valves - Method for sizing the operating element |
| EN 12627 | 工業閥門 鋼閥門的對焊端頭 | Industrial valves - Butt welding ends for steels valves |
| EN 1267 | 閥門 用水作為試驗流體的阻流試驗 | Valves - Test of flow resistance using water as test fluid |
| EN 12760 | 閥門 鋼閥門套接焊接端 | Valves - Socket welding ends for steel valves |
| EN 1286 | 衛生間泄水器 低壓機械混合閥 通用技術規范 | Sanitary tapware - Low pressure mechanical mixing valves - General technical specification |
| EN 1287 | 衛生間泄水器 低壓恒溫混合閥 通用技術規范 | Sanitary tapware - Low pressure thermostatic mixing valves - General technical specifications |
| EN 12982 | 工業閥門 對接焊端閥端面至端面以及中心至端面的尺寸 | Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves |
| EN 13082 | 危險品運輸罐 罐輔助設備 蒸汽輸送閥 | Tanks for transport of dangerous goods - Service equipment for tanks - Vapour transfer valve |
| EN 13152-2001+A1 | 液化石油氣瓶閥規范和測試 自動關閉閥 | Specification and testing of LPG cylinder valves - Self closing |
| EN 13153-2001+A1 | 液化石油氣瓶閥規范和測試 手工操作閥 | Specification and testing of LPG cylinder valves - Manually operated |
| EN 13175 | 液化石油氣（LPG）管閥門和裝配的規范和試驗 | Specification and testing for Liquefied Petroleum Gas (LPG) tank valves and fittings |
| EN 13244-4 | 地上和地下給排水和污水壓力系統用塑料管道 聚已烯（PE） 第4部分：閥門 | Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 4: Valves |
| EN 13308 | 危險品運輸罐 罐輔助設備 非壓力平衡底閥 | Tanks for transport of dangerous goods - Service equipment for tanks - Non pressure balanced footvalve |
| EN 13312-5 | 生物技術 管道和儀器性能標準 第5部分：閥 | Biotechnology - Performance criteria for piping and instrumentation - Part 5: Valves |
| EN 13316 | 危險品運輸罐 罐輔助設備 壓力平衡底閥 | Tanks for transporting dangerous goods - Service for tanks - Pressure balanced footvalve |
| EN 13397 | 工業閥門 金屬材料制成的隔膜閥 | Industrial valves - Diaphragm valves made of metallic materials |
| EN 1349-2000+AC | 工業加工控制閥門 | Industrial process control valves |
| EN 13648-1 | 低溫容器 抗過壓保護安全設備 第1部分：低溫服務用安全閥 | Cryogenic vessels - Safety devices for protection against excessive pressure - Part 1: Safety valves for cryogenic service |
| EN 1366-2 | 服務設施的耐火試驗 第2部分：防火閥 | Fire resistance tests for service installations - Part 2: Fire dampers |
| EN 13709 | 工業閥門 鋼球和球止回閥 | Industrial valves - Steel globe and globe stop and check valves |
| EN 13774 | 最大工作壓力小于或等于16 bar的氣體分配系統用閥門 性能要求 | Valves for gas distribution systems with maximum operating pressure less than or equal to 16 bar - Performance requirements |
| EN 13789 | 工業閥門 鑄鐵球閥 | Industrial valves - Cast iron globe valves |
| EN 13792 | 實驗室中使用的龍頭和閥門的色碼 | Colour coding of taps and valves for use in laboratories |
| EN 13828 | 建筑物閥門 建筑物中飲用水供水用手動銅合金及不銹鋼球閥 試驗和要求 | Building valves - Manually operated copper alloy and stainless steel ball valves for potable water supply in buildings - Test and requirements |
| EN 13942 | 石油和天然氣工業 管道運輸系統 管道閥門 | Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:1999, modified) |
| EN 13953 | 液化石油氣（LPG）用可運輸、可再裝油缸卸壓閥 | Pressure relief valves for transportable refillable cylinders for Liquefied Petroleum Gas (LPG) |
| EN 14189 | 可運輸氣瓶 氣瓶定期檢查時對瓶閥的檢查和維護 | Transportable gas cylinders - Inspection and maintenance of cylinder valves at time of periodic inspection of gas cylinders |
| EN 144-1-2000+A1 | 呼吸保護裝置 氣瓶閥 第1部分：插入式連接器用螺紋連接 | Respiratory protective devices - Gas cylinder valves - Part 1: Thread connections for insert connector |
| EN 144-2 | 呼吸保護裝置 氣瓶閥 第2部分：出口連接 | Respiratory protective devices - Gas cylinder valves - Part 2: Outlet connections |
| EN 144-3 | 呼吸保護裝置 氣瓶閥 第3部分：潛水氣體硝基氧和氧氣的出口連接 | Respiratory protective devices - Gas cylinder valves - Part 3: Outlet connections for diving gases Nitrox and oxygen |
| EN 1452-4 | 供水塑料管道系統 硬聚氯乙烯(PVC-U) 第4部分：閥門和附屬設備 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment |
| EN 1487 | 建筑閥門 水壓的安全類 試驗和要求 | Building valves - Hydraulic safety groups - Tests and requirements |
| EN 1488 | 建筑閥門 膨脹類 試驗和要求 | Building valves - Expansion groups - Tests and requirements |
| EN 1489 | 建筑閥門 壓力安全閥門 試驗和要求 | Building valves - Pressure safety valves - Tests and requirements |
| EN 1490 | 建筑閥門 兼有溫度及卸壓的組合閥 試驗和要求 | Building valves - Combined temperature and pressure relief valves - Tests and requirements |
| EN 1491 | 建筑筏門 膨脹閥 試驗和要求 | Building valves - Expansion valves - Tests and requirements |
| EN 1503-1 | 閥門 閥體、閥帽和閥套用材料 第1部分：歐洲標準中規定的鋼材 | Valves - Materials for bodies, bonnets and covers - Part 1: Steels specified in European Standards |
| EN 1503-2 | 閥門 閥體、閥帽和閥套用材料 第2部分：非歐洲標準規定的鋼材 | Valves - Materials for bodies, bonnets and covers - Part 2: Steels other than those specified in European Standards |
| EN 1503-3-2000+AC | 閥門 閥體、閥帽和罩閥套用材料 第3部分：歐洲標準規定的鑄鐵 | Valves - Materials for bodies, bonnets and covers - Part 3: Cast irons specified in European Standards |
| EN 1503-4 | 閥門 閥體、閥帽和閥套用材料 第3部分：歐洲標準規定的銅合金 | Valves - Materials for bodies, bonnets and covers - Part 4: Copper alloys specified in European Standards |
| EN 1555-4 | 供給氣體燃料用塑料管道系統 聚已烯(PE) 第4部分：閥門 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves |
| EN 1567 | 建筑閥門 減水壓閥門和組合減水壓閥門 要求和試驗 | Building valves - Water pressure reducing valves and combination water pressure reducing valves - Requirements and tests |
| EN 161 | 氣體燃燒器和燃氣器具自動關閉閥 | Automatic shut-off valves for gas burners and gas appliances |
| EN 1626 | 低溫容器 低溫設備用閥門 | Cryogenic vessels - Valves for cryogenic service |
| EN 1643 | 氣體燃燒器和氣體設備自動關閉閥門的閥門檢驗系統 | Valve proving systems for automatic shut-off valves for gas burners and gas appliances |
| EN 1680 | 塑料管道系統 聚乙烯(PE)管道系統用閥門 傳動裝置的彎曲時和彎曲后密封性的試驗方法 | Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanism |
| EN 1704 | 塑料管道系統 熱塑閥門 彎曲情況下溫度周期變化后閥門完整性的試驗方法 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after temperature cycling under bending |
| EN 1705 | 塑料管道系統 熱塑閥門 外部鼓風后閥門完整性試驗方法 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow |
| EN 1751 | 建筑物通風 氣路終端設備 閥與閥門的氣動試驗 | Ventilation for buildings - Air terminal devices - Aerodynamic testing of dampers and valves |
| EN 1759-3 | 法蘭及其接頭 管材、閥門、管件及附件用已命名種類的圓形法蘭 第2部分：銅合金法蘭 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 3: Copper alloy flanges |
| EN 1759-4 | 法蘭及其接頭 管材、閥門、管件及附件用已命名種類的圓形法蘭 第4部分：鋁合金法蘭 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 4: Aluminium alloy flanges |
| EN 1827 | 呼吸保護裝置 防止氣體或氣體和微?；騼H防顆粒的無吸入閥和帶可分離過濾器的半掩面罩 要求、試驗和標記 | Respiratory protective devices - Half masks without inhalation valves and with separable filters to protect against gases or gases and particles or particles only - Requirements, testing, marking |
| EN 19 | 工業閥門 金屬閥門的標志 | Industrial valves - Marking of metallic valves |
| EN 1984 | 工業閥門 鋼制閥門 | Industrial valves - Steel gate valves |
| EN 215-1-1987+AC1 | 恒溫散熱閥 第1部分：要求和試驗方法 | Thermostatic radiator valves; Part 1: Requirements and test methods |
| EN 26189 | 聲學 用于聽力保護的純音氣導閥聽力測定 | Acoustics; pure tone air conduction threshold audiometry for hearing conservation purposes (identical with ISO 6189:1983) |
| EN 26553 | 自動蒸汽疏水閥 標志 | Automatic steam traps-Marking (ISO 6553:1980) |
| EN 26554 | 法蘭連接自動蒸汽疏水閥 結構長度 | Flanged automatic steam traps-Face-to-face dimensions (ISO 6554:1980) |
| EN 26704 | 自動蒸汽疏水閥 分類 | Automatic steam traps-Classification (ISO 6704:1982) |
| EN 26948 | 自動蒸氣疏水閥 產品試驗和工作特性試驗 | Automatic steam traps-Production and performance characteristic tests (ISO 6948:1981) |
| EN 27841 | 自動蒸汽疏水閥門 漏氣量的測定 | Automatic steam traps-Determination of steam loss- Test methods (ISO 7841:1988) |
| EN 27842 | 自動蒸汽疏水閥門 排水量的測定 | Automatic steam traps- Determination of discharge capacity- Test methods (ISO 7842:1988) |
| EN 28233 | 熱塑性塑料閥門 扭矩 試驗方法 | Thermoplastics valves- Torque; test method (ISO 8233:1988) |
| EN 28659 | 熱塑性塑料閥門 疲勞強度 試驗方法 | Thermoplastic valves- Fatigue strength- Test method (ISO 8659:1989) |
| EN 331 | 建筑物燃氣設備用人工操縱球閥和封閉底錐形旋塞閥 | Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings |
| EN 405 | 呼吸保護設備 防氣體或防氣體和顆粒的閥濾式半面罩 要求、測試和標志 | Respiratory protective devices - Valved filtering half masks to protect against gases or gases and particles - Requirements, testing, marking |
| EN 417 | 用于便攜式灶具的、帶或不帶閥門的液化石油氣用一次性金屬氣筒 制作、檢驗、測試和標志 | Non-refillable metallic gas cartridges for liquefied petroleum gases, with or without a valve, for use with portable appliances - Construction, inspection, testing and marking |
| EN 45510-7-1 | 發電站設備、設備和系統的采購指南 第7-1部分：管道系統和閥門 高壓管道系統 | Guide for procurement of power station plant, equipment, and systems - Part 7-1: Pipework and valves - High pressure piping systems |
| EN 45510-7-2 | 發電站設備、設備和系統的采購指南 第7-2部分：管道系統和閥門 鍋爐和高壓管道閥 | Guide for procurement of power station plant, equipment, and systems - Part 7-2: Pipework and valves - Boiler and high pressure piping valves |
| EN 488 | 熱水分配管道 地下熱水網用預先絕熱包覆的管道系統 成套鋼鐵管道設備的管閥門組件、聚氨酯熱絕緣和聚乙 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN 558-1 | 工業閥門 法蘭管系統使用的金屬閥門面面間和中心與面間的尺寸 第1部分：PN標記的閥門 | Industrial valves - Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems - Part 1: PN-designated valves |
| EN 558-2 | 工業閥門 法蘭管系統使用的金屬閥門面面間和中心與面間的尺寸 第2部分：級別標記的閥門 | Industrial valves - Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems - Part 2: Class-designated valves |
| EN 561 | 氣焊設備 焊接、切割和同類處理用斷路閥門快速連接器 | Gas welding equipment - Quick-action coupling with shut-off valves for welding, cutting and allied processes |
| EN 593 | 工業閥門 金屬蝶閥 | Industrial valves - Metallic butterfly valves |
| EN 60099-1-1994+A1 | 避雷器 第1部分：交流系統用有間隙閥式避雷器 | Surge arresters - Part 1: Non-linear resistor type gapped surge arresters for a.c. systems (IEC 60099-1:1991) |
| EN 60534-1 | 工業過程控制閥 第1部分 控制閥術語和一般考慮 | Industrial-process control valves - Part 1: Control valve terminology and general considerations (IEC 60534-1:1987) |
| EN 60534-2-1 | 工業過程控制閥 第2－1部分：流通能力 安裝條件下流體流量的校準公式 | Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions (IEC 60534-2-1:1998) |
| EN 60534-2-3 | 工業過程控制閥 第２部分：流通能力 第３節：試驗規程 | Industrial-process control valves - Part 2-3: Flow capacity - Test procedures (IEC 60534-2-3:1997) |
| EN 60534-2-5 | 工業加工控制閥 第2-5部分：流量 通過帶級間恢復多級控制閥的流體尺寸方程 | Industrial-process control valves - Part 2-5: Flow capacity; Sizing equations for fluid flow through multistage control valves with interstage recovery (IEC 60534-2-5:2003) / Note: Endorsement notice |
| EN 60534-3-1 | 工業過程控制閥 第３－１部分：尺寸 法蘭雙通球形直型控制閥的端面間距尺寸和有法蘭雙通球型角型控制閥的 | Industrial-process control valves - Part 3-1: Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves (IEC 60534-3-1:2000) |
| EN 60534-3-2 | 工業過程控制閥 第３部分：尺寸 第２節：無法蘭控制閥（薄型蝶閥除外）的端面間距尺寸 | Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves (IEC 60534-3-2:2001) |
| EN 60534-3-3 | 工業過程控制閥 第三部分：尺寸 對接焊接 兩向 球型 垂直模式控制閥的末端對末端尺寸 | Industrial-process control valves - Part 3-3: Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves (IEC 60534-3-3:1998) |
| EN 60534-6-1 | 工業過程控制閥 第6－1部分：定位器聯到控制閥執行機構的安裝細則 第1節：直線傳動裝置上調節器的安裝 | Industrial-process control valves - Part 6: Mounting details for attachment of positioners to control valves - Section 1: Positioner mounting on linear actuators (IEC 60534-6-1:1997) |
| EN 60534-6-2 | 工業過程控制閥 第6－2部分：定位器聯到控制閥執行機構的安裝細則 環形執行機構定位器 | Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves; Positioner mounting on rotary actuators (IEC 60534-6-2:2000) |
| EN 60534-8-1 | 工業過程控制閥 第8部分：噪聲的考慮 第1節：氣動流流徑控制閥產生的噪聲的實驗室測量 | Industrial-process control valves - Part 8: Noise consideration; Section 1: Laboratory measurement of noise generated by hydrodynamic aerodynamic flow through control valves (IEC 60534-8-1:1986) |
| EN 60534-8-2 | 工業過程控制閥 第8部分 噪聲考慮 第2節通過控制閥的流體產生的噪聲的實驗室測量報法 | Industrial-process control valves- Part 8: noise consideration- Section 2: laboratory measurement of noise generated by hydrodynamic flow through control valves (IEC 60534-8-2:1991) |
| EN 60534-8-3 | 工業流程控制閥 .第8-3部分 噪聲問題 通過控制閥的動力噪聲預測法 | Industrial-process control valves - Part 8-3: Noise considerations; Control valve aerodynamic noise prediction method (IEC 60534-8-3:2000) |
| EN 60534-8-4 | 工業過程控制閥 第8部分：噪聲問題 第4節：流動產生的噪聲的預測 | Industrial-process control valves - Part 8: Noise considerations - Section 4: Prediction of noise generated by hydrodynamic flow (IEC 60534-8-4:1994) |
| EN 60700-1-1998+A12003 | 高壓直流(HVDC)電力傳輸半導體閘流閥 第1部分：電氣試驗 | Thyristor valves for high voltage direct current (HVDC) power transmission - Part 1: Electrical testing (IEC 60700-1:1998) |
| EN 60730-2-19 | 家用和類似用途的電氣自動化控制器 2-19部分：電動油閥的特殊要求（包括機械要求） | Automatic electric controls for household and similar use - Part 2-19: Particular requirements for electrically operated oil valves, including mechanical requirements (IEC 60730-2-19:1997 + A1:2000, modified) |
| EN 60730-2-8 | 家用和類似用途的電氣自動控制器 第２－８部分：電動水閥的特殊要求 包括機械要求 | Automatic electrical controls for household and similar use - Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements (IEC 60730-2-8:2000, modified) / Note: Endorsement notice |
| EN 60896-2 | 固定式鉛酸蓄電池 一般要求和試驗方法 第2部分：閥門調節型 | Stationary lead-acid batteries - General requirements and methods of test - Part 2: Valve regulated types (IEC 60896-2:1995) |
| EN 61056-1 | 一般用鉛酸蓄電池(閥調節型) 第1部分：一般要求、功能特性 試驗方法 | General purpose lead-acid batteries (valve regulated types) - Part 1: General requirements, functional characteristics, methods of test (IEC 61056-1:2002) / Note: Endorsement notice |
| EN 61056-2 | 一般用鉛酸蓄電池(閥調節型) 第2部分：尺寸、端子和標記 | General purpose lead-acid batteries (valve regulated types) - Part 2: Dimensions, terminals and marking (IEC 61056-2:2002) / Note: Endorsement notice |
| EN 61514 | 工業過程控制系統 氣動輸出閥門定位器性能評定方法 | Industrial-process controll systems - Methods of evaluating the performance of valve positioners with pneumatic outputs (IEC 61514:2000, modified) |
| EN 61954-1999+A1 | 輸電和配電系統用電力電子設備 靜態無功功率補償器用晶閘管閥的試驗 | Power electronics for electrical transmission and distribution systems - Testing of thyristor valves for static VAR compensators (IEC 61954:1999) |
| EN 629-1 | 可運輸氣瓶 連接氣瓶閥門用的25E錐螺紋 第1部分：規范 | Transportable gas cylinders - 25E taper thread for connection of valves to gas cylinders - Part 1: Specification |
| EN 629-2 | 可運輸氣瓶 連接氣瓶閥門的25E錐螺紋 第2部分：量規檢驗 | Transportable gas cylinders - 25E taper thread for connection of valves to gas cylinders - Part 2: Gauge inspection |
| EN 736-1 | 閥門 術語 第1部分：閥門類型定義 | Valves - Terminology - Part 1: Definition of types of valves |
| EN 736-2 | 閥門 術語 第2部分：閥門組件定義 | Valves - Terminology - Part 2: Definition of components of valves |
| EN 736-3-1999+A1 | 閥門 術語 第3部分：術語定義 | Valves - Terminology - Part 3: Definition of terms |
| EN 738-3-1998+A1 | 醫用氣體用壓力調節器 第3部分：帶氣瓶閥的壓力調節器 | Pressure regulators for use with medical gases - Part 3: Pressure regulators integrated with cylinder valves |
| EN 816 | 衛生間水開關制品 自動切斷閥PN 10 | Sanitary tapware - Automatic shut-off valves PN 10 |
| EN 849-1996+A1-1999+A2 | 可移動氣瓶 氣瓶閥 規范和定型測試 | Transportable gas cylinders - Cylinder valves - Specification and type testing |
| EN 850-1996+A1-2000+AC | 可移動氣瓶 醫用樞接軛狀閥門出口接頭 | Transportable gas cylinders - Pin-index, yoke-type valve outlet connections for medical use |
| EN 88-1991+A1 | 入口壓力200毫巴以下的燃氣器具的壓力調節閥 | Pressure governors for gas appliances for inlet pressures up to 200 mbar |
| EN 88/prA2 | 入口壓力200毫巴以下的燃氣器具的壓力調節閥 修改A2 | Pressure governors for gas appliances for inlet pressures up to 200 mbar; Amendment prA2 |
| EN 917 | 塑料管系統 熱塑閥門 抗內壓和泄漏密封性的試驗方法 | Plastics piping systems - Thermoplastics valves - Test methods for resistance to internal pressure and leaktightness |
| EN 962-1996+A1-1999+A2 | 可運輸氣瓶 工業和醫用氣瓶用閥保護帽和閥罩 設計、建造和試驗 | Transportable gas cylinders - Valve protection caps and valve guards for industrial and medical gas cylinders - Design, construction and tests |
| EN ISO 10432 | 石油和天然氣工業 下降孔設備 地下安全閥設備 | Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment (ISO 10432:1999) |
| EN ISO 10692-1 | 氣瓶 微電子工業用氣瓶閥接頭 第1部分：出口接頭 | Gas cylinders - Gas cylinder valve connections for use in the microelectronics industry - Part 1: Outlet connections (ISO 10692-1:2001) |
| EN ISO 10692-2 | 氣瓶 微電子工業用氣瓶閥接頭 第2部分：氣瓶閥接頭的規范和定型試驗 | Gas cylinders - Gas cylinder valve connections for use in microelectronic industry - Part 2: Specification and type testing for valve to cylinder connections (ISO 10692-2:2001) |
| EN ISO 11114-1-1997+AC | 可運輸氣瓶 氣瓶和瓶閥材料與盛裝氣體的相容性 第1部分：金屬材料 | Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 1: Metallic materials (ISO 11114-1:1997) |
| EN ISO 11114-2 | 可運輸氣瓶 氣瓶和瓶閥材料與盛裝氣體的相容性 第2部分：非金屬材料 | Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2000) |
| EN ISO 11114-3 | 可運輸氣瓶 氣瓶和瓶閥材料與盛裝氣體的相容性 第3部分：氧環境中自燃試驗 | Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 3: Autogenous ignition test in oxygen atmosphere (ISO 11114-3:1997) |
| EN ISO 11116-1 | 氣瓶 氣瓶與瓶閥連接用17E錐螺紋 第1部分：規范 | Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 1: Specifications (ISO 11116-1:1999) |
| EN ISO 11116-2 | 氣瓶 氣瓶與瓶閥連接用17E錐螺紋 第2部分：檢驗量規 | Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 2: Inspection gauges (ISO 11116-2:1999) |
| EN ISO 12209-1 | 氣瓶 壓縮可呼吸空氣用氣瓶閥的放氣連接器 第1部分：軛型連接器 | Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air - Part 1: Yoke type connections (ISO 12209-1:2000) |
| EN ISO 12209-2 | 氣瓶 壓縮可呼吸空氣用氣瓶閥的放氣連接器 第2部分：螺紋式連接器 | Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air - Part 2: Threaded connections (ISO 12209-2:2000) |
| EN ISO 12209-3 | 氣瓶 壓縮可呼吸空氣用氣瓶閥的放氣連接器 第3部分：230 bar 閥適配器 | Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air - Part 3: Adaptor for 230 bar valves (ISO 12209-3:2000) |
| EN ISO 13340 | 可運輸氣瓶 不可再充填的氣瓶用瓶閥 規范和原型試驗 | Transportable gas cylinders - Cylinder valves for non-refillable cylinders - Specification and prototype testing (ISO 13340:2001) |
| EN ISO 13341-1997+AC | 可運輸氣瓶 氣瓶閥的裝配 | Transportable gas cylinders - Fitting of valves to gas cylinders (ISO 13341:1997) |
| EN ISO 13758 | 液化石油氣 評價丙烷干燥度 閥凍結法 | Liquefied petroleum gases - Assessment of the dryness of propane - Valve freeze method (ISO 13758:1996) |
| EN ISO 14246 | 可運輸氣瓶 氣瓶閥門 生產試驗和檢驗 | Transportable gas cylinders - Gas cylinder valves - Manufacturing tests and inspections (ISO 14246:2001) |
| EN ISO 14723 | 石油和天然氣工業 管道輸送系統 海底管道閥 | Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2001) |
| EN ISO 15245-1 | 氣瓶 連接氣瓶閥門的平行螺紋 第1部分：規范 | Gas cylinders - Parallel threads for connection of valves to gas cylinders - Part 1: Specification (ISO 15245-1:2001) |
| EN ISO 15245-2 | 氣瓶 連接氣瓶閥門的平行螺紋 第2部分：量規檢驗 | Gas cylinders - Parallel threads for correction of valves to gas cylinders - Part 2: Gauge inspection (ISO 15245-2:2001) |
| EN ISO 15364 | 船舶與海上技術 散貨船真空/壓力閥 | Ships and marine technology - Pressure/vacuum valves for cargo tanks (ISO 15364:2000) |
| EN ISO 15761 | 石油及天然氣工業用DN100及較小的鋼閘閥 、球閥和防逆閥 | Steel gate, glob and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries (ISO 15761:2002) |
| EN ISO 3822-2 | 聲學 供水設施的裝置和設備發射的噪音的實驗室測定 第2部分：放水龍頭和混合閥的安裝和工作條件 | Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 2: Mounting and operating conditions for draw-off taps and mixing valves (ISO 3822-2:1995) |
| EN ISO 3822-3 | 聲學 供水設施的裝置和設備發射的噪音的實驗室測定 第3部分：管路閥門和器件的安裝和工作條件 | Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 3: Mounting and operating conditions for in-line valves and appliances |
| EN ISO 5135 | 聲學 在混響室中測定空調終端設備、空調終端單元、阻尼器和調節閥門的噪聲功率級 | Acoustics - Determination of sound power levels of noise from air-terminal devices, air-terminal units, dampers and valves by measurement in a reverberation room (ISO 5135:1997) |
| EN ISO 5210 | 通用閥門 多回轉閥門驅動裝置的連接 | Industrial valves - Multi-turn valve actuator attachments (ISO 5210:1991) |
| EN ISO 5211 | 通用閥門 轉動零件的激勵附件 | Industrial valves - Part-turn actuator attachments (ISO 5211:2001) |
| HD 1215.2-1988+AC1 | 熱靜力散熱器閥門 第2部分：尺寸和連接細節 | Thermostatic radiator valves; part 2: dimensions and details on connection |
| prEN 1074-6 | 供水閥門 目的要求的適應性和合適的認證試驗 第6部分：消防栓 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 6: Hydrants |
| prEN 12094-4 | 固定式消防系統 氣體滅火系統的部件 第4部分：對高壓容器閥組件及其驅動器的要求及試驗方法 | Fixed fire fighting systems - Components for gas extinguishing systems - Part 4: Requirements and test methods for high pressure container valve assemblies and their actuators |
| prEN 12116 | 工業閥門 部分回流閥驅動附件 | Industrial valves - Part-turn valve actuator attachment |
| prEN 12259-9 | 固定消防系統 噴水器和噴水系統構件 第9部分：集水閥 | Fixed firefighting systems - Components for sprinkler and water spray systems - Part 9: Deluge valves |
| prEN 12266-3 | 工業閥門 交貨技術條件 第3部分：試驗程序和驗收標準 | Industrial valves - Technical conditions of delivery - Part 3: Test procedures and acceptance criteria |
| prEN 12516-1 | 工業閥門 殼體設計強度 第1部分：鋼閥門殼體的列表法 | Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells |
| prEN 12516-2 | 工業閥門 殼體設計強度 第２部分：鋼閥門殼體的計算法 | Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
| prEN 13327 | 工業閥門 熱塑性材料止回閥 | Industrial valves - Check valves of thermoplastics materials |
| prEN 13547 | 工業閥門 銅合金球閥 | Industrial valves - Copper alloy ball valves |
| prEN 13617-3 | 加油站 第3部分：剪切閥構造和性能 | Petrol filling stations - Part 3: Construction and performance of shear valves |
| prEN 13786 | 用于丁烷、丙烷或其混和物的、最大出口壓力小于等于4bar的、流量最大可達100kg/h（包括100kg/h）的自動轉換 | Automatic change-over valves having a maximum outlet pressure of up to and including 4 bar with a capacity of up to and including 100 kg/h, and their associated safety devices for butane, propane or their mixtures |
| prEN 13959 | 公稱壓力在DN6至DN250（含DN250）的防污染控制閥 E族A、B、C和D型 | Anti-pollution check valves DN 6 to DN 250 inclusive - Family E, type A, B, C and D |
| prEN 14055-1 | 公廁沖洗池 第1部分：帶內溢流和閥門排水口裝置的沖洗池 | WC flushing cisterns - Part 1: Flushing cisterns with internal overflow and valve outlet mechanism |
| prEN 14071 | 液化石油氣（LPG）罐的減壓閥 輔助設備 | Pressure relief valves for LPG tanks - Ancillary equipment |
| prEN 14124 | 有內溢流的沖洗池的進水閥 | Inlet valves for flushing cisterns with internal overflow |
| prEN 14129 | 液化石油汽（LGP）罐壓力調節閥 | Pressure relief valves for LPG tanks |
| prEN 14141 | 天然氣管道輸送閥 試驗和性能要求 | Valves for natural gas transportation in pipelines - Performance requirements and tests |
| prEN 14341 | 工業閥 鋼防逆閥 | Industrial valves - Steel check valves |
| prEN 14432 | 危險貨物運輸罐 液態化工產品運輸?shù)墓拊O(shè)備 產品排放和進氣閥 | Tanks for the transport of dangerous goods - Tank equipment for the transport of liquid chemicals - Product discharge and air inlet valves |
| prEN 14433 | 危險貨物運輸罐 液態化工產品運輸?shù)墓拊O(shè)備 底閥 | Tanks for the transport of dangerous goods - Tank equipment for the transport of liquid chemicals - Footvalves |
| prEN 14451 | 飲用水的防回流污染裝置 包括公稱壓力在DN8-DN80內的管路反壓閥 D族 A型 | Devices to prevent pollution by backflow of potable water - In-line anti-vacuum valves DN 8 to DN 80 inclusive - Family D, type A |
| prEN 14455 | 飲用水的防回流污染裝置 包括公稱壓力在DN15-DN50內的壓縮空氣進氣閥 L族 A型和B型 | Devices to prevent pollution by backflow of potable water - Pressurised air inlet valves DN 15 to DN 50 inclusive - Family L, type A and type B |
| prEN 1456-4 | 地上和地下污廢水壓力排放用塑料管道系統 硬已烯(聚氯已烯)(PVC-U) 第4部分：閥門及輔助設備 | Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment |
| prEN 1531 | 包括啟動氣閥的調節氣閥 | Modulating gas valves including start gas valves |
| prEN 1759-1 | 法蘭及其接頭 管材、閥門、管件及附件用已命名種類的圓形法蘭 第1部分：鋼法蘭NPS1/2到24 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| prEN 1983 | 工業鋼球閥 | Industrial valves - Steel ball valves |
| prEN 215-2 | 恒溫散熱閥 第2部分：連接尺寸和細節 | Thermostatic radiator valves; part 2: dimensions and details on connection |
| prEN 332 | 壓力不超過PN 0,2 和壓力為DN 15 至DN 50間的家用氣體裝置用封閉底人工操縱金屬錐形旋塞關閉閥 | Manually operated metallic taper plug shut-off valves with closed bottom for domestic gas installations for pressures up to PN 0,2 and with DN 15 to DN 50 |
| prEN 333 | 壓力不超過PN 4 和壓力為DN 15 至DN 50間的家用氣體裝置用人工操縱金屬球關閉閥 | Manually operated metallic ball shut-off valves for domestic gas installations up to PN 4 and with DN 15 to DN 50 |
| prEN 45511 | 采購指南 電氣設備閥 開關設備和控制裝置 | Guide for procurement - Electrical equipment - Switchgear and controlgear |
| prEN 45512 | 采購指南 管道系統和閥 包括安全閥的鍋爐和高壓管道閥 | Guide for procurement - Pipework and valves - Boiler and high pressure piping valves including safety valves |
| prEN 45513 | 采購指南 管道系統和閥 包括支架的高壓管線 | Guide for procurement - Pipework and valves - High pressure piping including supports |
| prEN 50105 | 固定式鉛酸蓄電池組 一般要求和試驗方法 閥門調節類型 | Stationary lead-acid batteries; general requirements and test methods; valve regulated types |
| prEN 558-3 | 法蘭管系統使用的金屬閥門 面面間和中心與面間的尺寸 第3部分：級別標記的閥門 | Metal valves for use in flanged pipe systems; face-to-face and centre-to-face dimensions; part 3: class-designation valves |
| prEN 593 | 工業閥門 金屬蝶閥 | Industrial valves - Metallic butterfly valves / Note: Intended as replacement for EN 593 (1998-01). |
| prEN 60534-4 | 工業過程控制閥 第４部分：檢驗和常規試驗 草案 | IEC 60534-4: Industrial-process control valves - Part 4: Inspection and routine testing |
| prEN 628 | 氣瓶 連接25.8mm公稱直徑氣瓶閥門用的錐形螺紋量規檢測要求 | Gas cylinders; requirements for gauge inspection of tapered threads for connection of valves to gas cylinders of 25.8 mm nominal diameter |
| prEN ISO 10297 | 可運輸?shù)臍馄俊￠y門 規范及定型試驗 | Transportable gas cylinders - Cylinder valves - Specification and type testing (ISO/DIS 10297:2002) |
| prEN ISO 10434 | 石油和天然氣工業用螺栓帽狀鋼閘閥 | Bolted bonnet steel gate valves for petroleum and natural gas industries (ISO/DIS 10434:2002) |
| prEN ISO 10497 | 閥門試驗 閥門耐火試驗要求 | Testing of valves - Fire type-testing requirements (ISO/DIS 10497:2002) |
| prEN ISO 11219 | 氣瓶 氣瓶與瓶閥連接用17E錐螺紋 檢驗量規 | Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Inspection gauges (ISO/DIS 11219:1996) |
| prEN ISO 14617-8 | 圖表用圖形符號 第8部分：閥及擋板 | Graphical symbols for diagrams - Part 8: Valves and dampers (ISO/FDIS 14617-8:2002) |
| prEN ISO 16135 | 工業用閥門 熱塑性材料制球閥 | Industrial valves - Ball valves of thermoplastic materials (ISO/DIS 16135:2001) |
| prEN ISO 16136 | 工業用閥門 熱塑性材料制蝶閥 | Industrial valves - Butterfly valves of thermoplastic materials (ISO/DIS 16136:2001) |
| prEN ISO 16137 | 工業用閥門 熱塑性材料制防逆閥 | Industrial valves - Check valves of thermoplastic materials (ISO/DIS 16137:2001) |
| prEN ISO 16138 | 工業用閥門 熱塑性材料制隔膜閥 | Industrial valves - Diaphragm valves of thermoplastic materials (ISO/DIS 16138:2001) |
| prEN ISO 16139 | 工業用閥門 熱塑性材料制閘閥 | Industrial valves - Gate valves for thermoplastic materials (ISO/DIS 16139:2000) |
| prEN ISO 17292 | 石油、石油化工及相關工業用金屬球閥 | Metal ball valves for petroleum, petrochemical and allied industries (ISO/DIS 17292:2002) / Note: Endorsement notice |
| prEN ISO 21787 | 工業閥門 熱塑塑料制球閥 | Industrial valves - Globe valves of thermoplastic materials (ISO/DIS 21787:2001) |
| prEN ISO 407 | 小型醫用氣瓶 針導軛式閥連接 | Small medical gas cylinders - PIN-index yoke-type valve connections (ISO/DIS 407:2001) |
| prEN ISO 4126-1 | 防止過壓防護的安全裝置 第1部分：安全閥 | Safety devices for protection against excessive pressure - Part 1: Safety valves (ISO/FDIS 4126-1:2003) |
| prEN ISO 4126-4 | 保護額外壓力的安全設備 第4部分：飛行員操作安全閥 | Safety devices for the protection against excessive pressure - Part 4: Pilot operated safety valves (ISO/FDIS 4126-4:2003) |
| 編號 | 中文名稱 | 英文名稱 |