微信掃一掃，立即回復！
| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| EN 1113 | 衛生水龍頭用淋浴設備軟管（PN10） | Showers hoses for (PN 10) sanitary tapware |
| EN 12083-1998+AC | 呼吸保護裝置 帶呼吸軟管的過濾器（無面罩式過濾器） 微粒過濾器、氣體過濾器和混合式過濾器 要求、試驗 | Respiratory protective devices - Filters with breathing hoses (Non-mask mounted filters) - Particle filters, gas filters, and combined filters - Requirements, testing, marking |
| EN 12115 | 液體或氣體化學藥品用的橡膠和熱塑軟管和軟管組件 規范 | Rubber and thermoplastics hoses and hose assemblies for liquid or gaseous chemicals - Specification |
| EN 12374 | 包裝 軟管 術語 | Packaging - Flexible tubes - Terminology |
| EN 12377 | 包裝 軟管 封閉氣密性的試驗方法 | Packaging - Flexible tubes - Test method for the airtightness of closures |
| EN 12434-2000+AC | 低溫容器 低溫軟管 | Cryogenic vessels - Cryogenic flexible hoses |
| EN 1256 | 氣焊設備 焊接切割及類似加工設備的軟管附件規范 | Gas welding equipment - Specification for hose assemblies for equipment for welding, cutting and allied processes |
| EN 1327 | 氣焊設備 焊接和相關工藝用熱塑軟管 | Gas welding equipment - Thermoplastic hoses for welding and allied processes |
| EN 13482 | 瀝青用橡膠軟管和軟管組件 規范 | Rubber hoses and hose assemblies for asphalt and bitumen - Specification |
| EN 1360 | 受測燃料配制用橡膠軟管和軟管部件 規范 | Rubber hoses and hose assemblies for measured fuel dispensing - Specification |
| EN 1361 | 飛行燃油處理用橡膠軟管和軟管組件 規范 | Rubber hoses and hose assemblies for aviation fuel handling - Specification |
| EN 13765 | 輸送烴類溶劑和化學制品的熱塑性多層（非硫化）軟管和軟管組件 規范 | Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification |
| EN 13766 | 輸送烴類溶劑和化學制品的熱塑性多層（非硫化）軟管和軟管組件 規范 | Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - Specification |
| EN 138 | 呼吸保護裝置 與全罩式面罩、半罩式面罩或口罩一起使用的新鮮空氣軟管呼吸器 要求、測試、標志 | Respiratory protective devices - Fresh air hose breathing apparatus for use with full face mask, half mask or mouthpiece assembly - Requirements, testing, marking |
| EN 13905 | 衛生座便器用低阻力噴射排水軟管 | Low resistance shower hoses for sanitary tapware |
| EN 1736 | 制冷系統和熱泵 軟管元件 振動隔離器和伸縮接頭 要求、設計和安裝 | Refrigerating systems and heat pumps - Flexible pipe elements, vibration isolators and expansion joints - Requirements, design and installation |
| EN 1761 | 燃料卡車送貨用的橡膠軟管和軟管組件 規范 | Rubber hoses and hose assemblies for fuel truck delivery - Specification |
| EN 1762 | 氣壓為25bar(2.5MPa)及以下的液化石油氣LPG(液相或氣相)及天然氣用橡膠軟管和軟管組件 規范 | Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification |
| EN 1765 | 油的吸放裝置用橡膠軟管組裝件 組裝件規范 | Rubber hose assemblies for oil suction and discharge services - Specification for the assemblies |
| EN 1947 | 消防軟管 水泵及車輛用半剛性輸送水軟管組裝件 | Fire-fighting hoses - Semi-rigid delivery hoses and hose assemblies for pumps and vehicles |
| EN 24641 | 給水和排水用橡膠軟管 規范 | Rubber hoses for water and discharge; specification (ISO 4641:1991) |
| EN 26801 | 橡膠或塑料軟管 容積膨脹的測定 | Rubber or plastics hoses-Determination of volumetric expansion (ISO 6801:1983) |
| EN 26802 | 鋼絲增強的橡膠和塑料軟管及軟管件 彎抗沖擊試驗 | Rubber and plastics hoses and hose assemblies, wire reinforced- Hydraulic impulse test with flexing (ISO 6802:1991) |
| EN 269 | 呼吸保護裝置 包括護罩的動力推動新鮮空氣軟管呼吸器 要求、測試、標志 | Respiratory protective devices - Powered fresh air hose breathing apparatus incorporating a hood - Requirements, testing, marking |
| EN 271-1995+A1-2000+AC1997 | 呼吸保護裝置 用于噴砂操作的包括護罩的壓縮空氣導管呼吸器或動力推動新鮮空氣軟管呼吸器 要求、測試、標 | Respiratory protective devices - Compressed air line or powered fresh air hose breathing apparatus incorporating a hood for use in abrasive blasting operations - Requirements, testing, marking |
| EN 27326 | 橡膠和塑料軟管 靜態條件下耐臭氧性的評定 | Rubber and plastics hoses-Assessment of ozone resistance under static conditions (ISO 7326:1991) |
| EN 28029 | 塑料軟管 通用型可折疊織物增強輸水軟管 規范 | Plastics hose-General purpose collapsible water hose, textile reinforced-Specification (ISO 8029:1985) |
| EN 28033 | 橡膠和塑料軟管 部件間粘合強度的測定 | Rubber and plastic hoses-Determination of adhesion between components (ISO 8033:1991) |
| EN 29168 | 手持式牙科器械 軟管連接件 | Dental handpieces - Hose connectors (ISO 9168:1991) |
| EN 559 | 氣焊設備 焊接、切割和同類處理用橡膠軟管 | Gas welding equipment - Rubber hoses for welding, cutting and allied processes |
| EN 560 | 氣焊設備 焊接、切割和同類處理用設備的軟管連接 | Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes |
| EN 60684-2-1997+A1 | 絕緣軟管 第2部分：試驗方法 | Flexible insulating sleeving - Part 2: Methods of test (IEC 60684-2:1997) |
| EN 60684-3-100 bis 105 | 絕緣軟管 第3部分：各種型號軟管規范 活頁100至105：擠壓聚氯乙烯(PVC)軟管 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving; Sheets 100 to 105: Extruded PVC sleeving (IEC 60684-3-100 to 105:2001) |
| EN 60684-3-121 bis 124 | 絕緣軟管 第3部分：各種型號軟管規范 活頁121至124：擠壓有機硅軟管 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving; Sheets 121 to 124: Extruded silicone sleeving (IEC 60684-3-121 to 124:2001) |
| EN 60684-3-145 bis 147 | 絕緣軟管 第3部分：各種型號軟管規范 活頁145至147：擠壓聚四氟乙烯(PTFE)軟管 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving; Sheets 145 to 147: Extruded PTFE sleeving (IEC 60684-3-145 to 147:2001) |
| EN 60684-3-151 | 絕緣軟套管 第3部分：?jiǎn)涡吞坠艿奶厥庖蠡铐?yè)151：通用擠壓PVC／晴橡膠軟管 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 151: Extruded PVC/nitrile rubber - General purpose (IEC 60684-3-151:1998) |
| EN 60684-3-217 | 絕緣軟管 第3部分：?jiǎn)涡吞坠艿奶厥庖蟆』铐?yè)217：熱縮聚烯烴套管 阻燃 收縮比3：1 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 217: Heat-shrinkable polyolefin sleeving, flame retarded, shrink ratio 3:1 (IEC 60684-3-217:1998) |
| EN 60684-3-218 | 絕緣軟管 第3部分：?jiǎn)涡吞坠艿奶厥庖蟆』铐?yè)218：.熱縮聚烯烴套管 不阻燃 手縮比3：1 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 218: Heat-shrinkable polyolefine sleeving, not flame retarded, shrink ratio 3:1 (IEC 60684-3-218:1998) |
| EN 60684-3-228 | 絕緣軟管 第3部分：各種型號軟管規范 活頁228：熱縮半剛性聚偏二氟乙烯套管 阻燃 耐流體 收縮率2：1 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 228: Heat-shrinkable, semi-rigid polyvinylidene fluoride sleeving, flame retarded, fluid resistant, shrink ratio 2:1 (IEC 60684-3-228:1998) |
| EN 60684-3-233 | 絕緣軟管 第3部分 各種型號套管的規范要求 活頁２３３：熱收縮氟彈性體軟管 阻燃 耐流體 收縮比２： | Flexible insulating sleeving - Part 3: Specification for individual types of sleeving - Sheet 233: Heat-shrinkable fluoroelastomer sleeving, flame retarded, fluid resistant, shrink ratio 2:1 (IEC 60684-3-233:1998) |
| EN 60684-3-246 | 絕緣軟管 第3部分：各種型號套管的規范要求 活頁２４６：聚烯烴不阻燃雙層壁熱收縮套管 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving; Sheet 246: Heat-shrinkable polyolefin sleeving, dual-wall, not flame-retarded (IEC 60684-3-246:2001) |
| EN 60684-3-271 | 絕緣軟管 第3部分：各種型號套管的規范 活頁271：熱收縮彈性軟管 阻燃 耐流體 收縮比2：1 | Flexible insulating sleeving - Part 3: Specification for individual types of sleeving - Sheet 271: Heat-shrinkable elastomer sleeving, flame retarded, fluid resistant, shrink ratio 2:1 (IEC 60684-3-271:1998) |
| EN 60684-3-272 | 絕緣軟管 第3部分：各種型號軟管規范 活頁272：熱收縮彈性軟管 阻燃 耐流體 收縮比2：1 薄壁 | Flexible insulating sleeving - Part 3: Specification for individual types of sleeving - Sheet 272: Heat-shrinkable elastomer sleeving, flame retarded, fluid resistant, shrink ratio 2:1, thin wall (IEC 60684-3-272:1998) |
| EN 60684-3-409 | 絕緣軟套管 第3部分：各種型號套管規范 活頁409：聚胺脂(PUR)涂覆層的玻璃纖維軟管 | Flexible insulating sleeving - Part 3: Specification for individual types of sleeving - Sheet 409: Glass textile sleeving with polyurethane (PUR)-based coating (IEC 60684-3-409:1999) |
| EN 61479 | 帶電作業 絕緣材料制軟導線外皮(線軟管) | Live working - Flexible conductor covers (line hoses) of insulating material (IEC 61479:2001) |
| EN 61770 | 與總水管連接的電氣器具 避免軟管組件的反虹吸和失效 | Electric appliances connected to the water mains - Avoidance of backsiphonage and failure of hose-sets (IEC 61770-1998) |
| EN 739-1998+A1 | 醫療氣體設備用低壓軟管組件 | Low-pressure hose assemblies for use with medical gases |
| EN 853 | 橡膠軟管和軟管配件 金屬絲編織加強液壓型 規范 | Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification |
| EN 854 | 橡膠軟管和軟管配件 紡織增強液壓型 規范 | Rubber hoses and hose assemblies - Textile reinforced hydraulic type - Specification |
| EN 855 | 塑料軟管和軟管配件 熱塑料織物增強液壓型 規范 | Plastics hoses and hose assemblies - Thermoplastics textile reinforced hydraulic type - Specification |
| EN 856 | 橡膠軟管和軟管配件 橡膠 包覆螺形線增強液壓型 規范 | Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification |
| EN 857 | 橡膠軟管和軟管配件 液壓設備用金屬絲編織增強壓制型 規范 | Rubber hoses and hose assemblies - Wire braid reinforced compact type for hydraulic applications - Specification |
| EN ISO 10380 | 管道系統 波紋金屬軟管和軟管組件 | Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2003) |
| EN ISO 10960 | 橡膠和塑料軟管 動態條件下耐臭氧性的評定 | Rubber and plastics hoses - Assessment of ozone resistance under dynamic conditions (ISO 10960:1994) |
| EN ISO 11758-1997+AC | 橡膠和塑料軟管 氙弧燈照射 顏色和外觀變化的測定 | Rubber and plastics hoses - Exposure to a xenon arc lamp - Determination of changes in colour and appearance (ISO 11758:1995) |
| EN ISO 1307 | 一般工業用橡膠和塑料軟管 孔徑和公差及長度公差 | Rubber and plastics hoses for general-purpose industrial applications - Bore diameters and tolerances, and tolerances on length (ISO 1307:1992) |
| EN ISO 13628-2 | 石油和天然氣工業 水下采油系統的設計和操作 第2部分：海底和海洋設備用軟管系統 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 2: Flexible pipe systems for subsea and marine applications (ISO 13628-2:2000) |
| EN ISO 1401 | 農業噴霧用橡膠軟管 | Rubber hoses for agricultural spraying (ISO 1401:1999) |
| EN ISO 1402 | 橡膠和塑料軟管和軟管組件 液壓試驗 | Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:1994) |
| EN ISO 1403 | 一般用途的輸水橡膠軟管 規范 | Rubber hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 1403:1995) |
| EN ISO 14113 | 氣焊設備 最大設計壓力為450bar的壓塑空氣和液化氣用橡膠和塑料軟管組件 | Gas welding equipment - Rubber and plastic hoses assembled for compressed or liquefied gases up to a maximum design pressure of 450 bar (ISO 14113:1997) |
| EN ISO 15540 | 船舶與造船技術 軟管組件耐火性 試驗方法 | Ships and marine technology - Fire resistance of hose assemblies - Test methods (ISO 15540:1999) |
| EN ISO 15541 | 船舶與造船技術 軟管組件耐火性 試驗臺技術要求 | Ships and marine technology - Fire resistance of hose assemblies - Requirements for the test bench (ISO 15541:1999) |
| EN ISO 1746 | 橡膠或塑料軟管和管件 彎曲試驗 | Rubber or plastics hoses and tubing - Bending tests (ISO 1746:1998, including technical corrigendum 1:1999) |
| EN ISO 2398 | 織物增強的壓縮空氣用橡膠軟管 規范 | Rubber hose, textile-reinforced, for compressed air - Specification (ISO 2398:1995) |
| EN ISO 3861 | 噴砂用橡膠軟管 規范 | Rubber hoses for sand and grit blasting - Specification (ISO 3861:1995) |
| EN ISO 3994 | 塑料軟管 給排水用螺紋型熱塑性軟管 規范 | Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification (ISO 3994:1998) |
| EN ISO 4023 | 蒸氣膠管 試驗方法 | Rubber hoses for steam - Test methods (ISO 4023:1991) |
| EN ISO 4080-1995+AC | 橡膠與塑料軟管和軟管組件 漏氣氯的測定 | Rubber and plastics hoses and hose assemblies - Determination of permeability to gas (ISO 4080:1991) |
| EN ISO 4671 | 橡膠和塑料軟管和軟管組件 尺寸測量方法 | Rubber and plastics hoses and hose assemblies - Methods of measurement of dimensions (ISO 4671:1999) |
| EN ISO 4672 | 橡膠和塑料軟管 低溫的彎曲試驗 | Rubber and plastics hoses - Sub-ambient temperature flexibility tests (ISO 4672:1997) |
| EN ISO 5771 | 輸送無水氨用橡膠軟管和軟管組件 規范 | Rubber hose and hose assemblies for transferring anhydrous ammonia - Specification (including Corr 1:1995) |
| EN ISO 5774 | 壓縮空氣用織物增強的塑料軟管 規范 | Plastics hoses, textile-reinforced, for compressed air - Specification (ISO 5774:1997) |
| EN ISO 6224 | 一般用途輸水用織物增強塑料軟管 規范 | Plastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:1995) |
| EN ISO 6803 | 橡膠或塑料軟管和軟管組件 無彎曲的液壓脈沖試驗 | Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing (ISO 6803:1994) |
| EN ISO 6806 | 油燃燒器用軟管和軟管組件 規范 | Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:1992) |
| EN ISO 6808 | 給排油用塑料軟管和軟管組件 規范 | Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification (ISO 6808:1999) |
| EN ISO 6945-1996+A1 | 橡膠軟管 外覆層耐磨性的測定 | Rubber hoses - Determination of abrasion resistance of the outer cover (ISO 6945:1991) |
| EN ISO 7233 | 橡膠和塑料軟管和軟管組件 耐真空性能測定 | Rubber and plastics hoses and hose assemblies - Determination of suction resistance (ISO 7233:1991) |
| EN ISO 7662 | 橡膠和塑料軟管 襯里耐磨性的測定 | Rubber and plastics hoses - Determination of abrasion of lining (ISO 7662:1988) |
| EN ISO 7751 | 橡膠和塑料軟管和軟管組件 試驗壓力和爆破壓力對設計工作壓力的比值 | Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to design working pressure (ISO 7751:1991) |
| EN ISO 7840-1995+A1 | 小艇 耐火燃油軟管 | Small craft - Fire resistant fuel hoses (ISO 7840:1994) |
| EN ISO 8028 | 真空噴涂漆用橡膠和／或塑料軟管和軟管組件 規范 | Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO 8028:1999) |
| EN ISO 8030 | 橡膠和塑料軟管 易燃燒性試驗方法 | Rubber and plastics hoses - Method of test for flammability (ISO 8030:1995) |
| EN ISO 8031 | 橡膠和塑料軟管和軟管組件 電阻率測定 | Rubber and plastics hoses and hose assemblies - Determination of electrical resistance (ISO 8031:1993) |
| EN ISO 8032 | 橡膠和塑料軟管和軟管組件 液壓脈沖彎曲試驗(半歐姆型試驗) | Rubber and plastics hose assemblies - Flexing combined with hydraulic impulse test (half-omega test) (ISO 8032:1997) |
| EN ISO 8308 | 橡膠和塑料軟管和管件 液體透過管壁性能測定 | Rubber and plastics hoses and tubing - Determination of transmission of liquids through hose and tubing walls (ISO 8308:1993) |
| EN ISO 8330 | 橡膠和塑料軟管和軟管組件 詞匯 | Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:1998) |
| EN ISO 8469-1995+A1 | 小艇 非耐火燃油軟管 | Small craft - Non-fire resistant fuel hoses (ISO 8469:1994) / Note: To be replaced by prEN ISO 8469 (2003-09). |
| EN ISO 8580 | 橡膠與塑料軟管 穩定狀態下耐紫外線的測定 | Rubber and plastic hoses - Determination of ultra-violet resistance under static conditions (ISO 8580:1987) |
| HD 523.3.201 S1 | 絕緣軟管規范 第3部分：各種型號軟管的規范要求 活頁201：通用軟交聯聚氯乙烯熱收縮軟管，收縮比為2：1 | Specification for flexible insulation sleeving; part 3: specification requirements for individual types of sleeving; sheet 201: heat shrinkable sleeving, general purpose, flexible, cross-linked PVC, shrink ratio 2:1 (IEC 60684-3-201:1991) |
| prEN 10324 | 鋼絲和鋼絲制品 軟管增強用鋼絲 | Steel wire and wire products - Hose reinforcement wire |
| prEN 13483 | 測量加油機用帶內部蒸汽回收的軟管及軟管組件 規范 | Hoses and hose assemblies with internal vapour recovery for measured fuel dispensing system - Specification |
| prEN 1361 | 飛行燃油處理用橡膠軟管和軟管組件 規范 | Rubber hoses and hose assemblies for aviation fuel handling - Specification |
| prEN 13618 | 供水撓性軟管（金屬的和彈性材料） 規范和試驗方法 | Water supply - Flexible hoses (elastomeric or plastic material hose with or without metallic or synthetic braiding) - Product standard |
| prEN 14420-1 | 帶夾具的軟管配件 第1部分：試驗和名稱、測量、要求 | Hose fittings with clamp units - Part 1: Requirements, survey, designation and testing |
| prEN 14420-10 | 帶夾具的軟管配件 第10部分：凸輪鎖緊連接規格 | Hose fittings with clamp units - Part 10: Gauges for cam-locking couplings |
| prEN 14420-11 | 帶夾具的軟管配件 第11部分： 對稱半連接規格（圭勒明方法） | Hose fittings with clamp units - Part 11: Gauges for symmetrical half couplings (Guillemin system) |
| prEN 14420-2 | 帶夾具的軟管配件 第2部分：軟管支架的軟管附屬部分 尺寸和類型 | Hose fittings with clamp units - Part 2: Hoses side parts of hose shank; Dimensions and types |
| prEN 14420-3 | 帶夾具的軟管配件 第3部分：銷式或螺栓式夾具 | Hose fittings with clamp units - Part 3: Clamp units, pinned or bolted |
| prEN 14420-4 | 帶夾具的軟管配件 第4部分：法蘭連接 | Hose fittings with clamp units - Part 4: Flange connections |
| prEN 14420-5 | 帶夾具的軟管配件 第5部分：螺紋連接 | Hose fittings with clamp units - Part 5: Threaded connections |
| prEN 14420-6 | 帶夾具的軟管配件 第6部分：：TW罐式卡車連接 | Hose fittings with clamp units - Part 6: TW tank truck couplings |
| prEN 14420-7 | 帶夾具的軟管配件 第7部分：凸輪鎖緊 | Hose fittings with clamp units - Part 7: Cam locking couplings |
| prEN 14420-8 | 帶夾具的軟管配件 第8部分：對稱半連接（圭勒明方法） | Hose fittings with clamp units - Part 8: Symmetrical half coupling (Guillemin system) |
| prEN 14420-9 | 帶夾具的軟管配件 第9部分：TW罐式卡車連接規格 | Hose fittings with clamp units - Part 9: Gauges for TW tank truck couplings |
| prEN 14421 | 卷縮和彎曲的軟管口和金屬環 | Hose tail and ferrule for crimping and swaging |
| prEN 14422 | 液化石油氣軟管用夾具型連接組件 | Clamp type coupling assemblies for LPG transfer hoses |
| prEN 14423 | 額定壓力達18bar在DN15-DN50的蒸氣軟管用夾具型連接組件 | Clamp type coupling assemblies for use with DN 15 to DN 50 steam hoses rated for pressures up to 18 bar |
| prEN 14424 | 帶螺紋箍的軟管配件 | Hose fittings with screwed ferrules |
| prEN 14454 | 飲用水的防回流污染裝置 包括公稱壓力在DN15-DN32內的軟管組合流阻止器 H族 A型 | Devices to prevent pollution by backflow of potable water - Hose union backflow preventer DN 15 to DN 32 inclusive - Family H, Type A |
| prEN 1762 | 氣壓為25bar(2.5MPa)液化石油氣LPG(液相或氣相)及天然氣用橡膠軟管和軟管組件 規范 | Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification / Note: Intended as replacement for EN 1762 (1997-10). |
| prEN 1763-2 | 供氣相丙烷和丁烷使用的撓性軟管、管道及組裝件 第2部分：對管咀接頭及組裝件的要求 | Flexible hose, tubing and assemblies for use with propane and butane in the vapour phase - Part 2: Requirements for nozzles, couplings and assemblies |
| prEN 1765 | 油的吸放裝置用橡膠軟管組裝件 組裝件規范 | Rubber hose assemblies for oil suction and discharge services - Specification for the assemblies |
| prEN 1924 | 用于急救軟管設備的不滲透吹塑軟管 | Fire-fighting hoses - Non-percolating layflat delivery hoses and hose assemblies for pumps and vehicles |
| prEN 3086 | 航空航天系列 軟管系統 符號表示到15位 | Aerospace series - Hose assemblies - Designation limited to 15 digits |
| prEN 60684-3-214 | 絕緣軟套管 第3部分：各種型號軟管規范 活頁214：熱縮聚烯烴軟管 不阻燃 收縮比3：1厚壁和中厚壁 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving; Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, shrink ratio 3:1; Thick and medium wall |
| prEN 60684-3-216 | 絕緣軟套管 第3部分：各種型號軟管規范 活頁216：熱縮 阻燃 有限著火危險軟管 | IEC 60684-3-216: Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving; Sheet 216: Heat-shrinkable, flame-retarded, limited fire hazard sleeving |
| prEN ISO 15465 | 管道工程 條繞金屬軟管和軟管組件 | Pipework - Stripwound metal hoses and hose assemblies (ISO/DIS 15465:2002) |
| prEN ISO 6134 | 飽和水蒸汽橡膠軟管和軟管組件 規范 | Rubber hoses and hose assemblies for saturated steam - Specification (ISO/DIS 6134:1999) |
| prEN ISO 6807 | 旋轉式鉆探和振動用橡膠軟管和軟管組件 規范 | Rubber hoses and hose assemblies for rotary drilling and vibration applications - Specification (ISO/FDIS 6807:2003) |
| prEN ISO 7369 | 管道工程 金屬軟管和軟管裝備 詞匯 | Pipework - Metal hoses and hose assemblies - Vocabulary (ISO/DIS 7369:2002) |
| 編號 | 中文名稱 | 英文名稱 |