微信掃一掃，立即回復！
| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| DL/T 695 | 電站鋼制對焊管件 | () |
| DL/T 935 | 鋼塑復合管和管件 | () |
| GB 15558.2 | 燃?xì)庥寐竦鼐垡蚁?PE)管道系統第2部分:管件 | Buried Polyethylene(PE)piping systems for the supply of gaseous fuels Part 2:Fittings |
| GB/T 12459 | 鋼制對焊無縫管件 | Steel butt-welding seamless pipe fittings |
| GB/T 12772 | 排水用柔性接口鑄鐵管及管件 | Cast iron pipes and fittings with flexible joint sewerage |
| GB/T 13021 | 聚乙烯管材和管件炭黑含量的測定熱失重法 | Determination for the carbon black content of polyethylene pipes and fittings by calcination and pyrolysis |
| GB/T 13295 | 水及燃?xì)夤艿烙们蚰T鐵管、管件和附件 | Ductile iron pipes，fittings and accessories for water or gas applications |
| GB/T 13401 | 鋼板制對焊管件 | Steel plate butt-welding pipe fittings |
| GB/T 13663.2 | 給水用聚乙烯(PE)管道系統第2部分:管件 | Polyethylene(PE)pipings systems for water supply Part 2:Fittings |
| GB/T 14383 | 鍛鋼制承插焊管件 | Forged steel socket welding pipe fittings |
| GB/T 14626 | 鍛鋼制螺紋管件 | Forged steel threaded pipe fittings |
| GB/T 15819 | 灌溉用聚乙烯(PE)管材由插入式管件引起環境應力開裂敏感性的試驗方法和技術要求 | Polyethylene (PE) pipes for irrigation laterals - Susceptibility to envionmental stress cracking induced by insert-type fittings - Test method and specification |
| GB/T 15820 | 聚乙烯壓力管材與管件連接的耐拉拔試驗 | Test of resistance to pull out ofjoints between polyethylene (PE) pressure pipes and fittings |
| GB/T 17185 | 鋼制法蘭管件 | Steel pipe fittings for flanged joint |
| GB/T 17241.1 | 鑄鐵管法蘭類型 | Synoptic table for cast iron pipe flanges |
| GB/T 17241.2 | 鑄鐵管法蘭蓋 | Cast iron pipe blank flanges |
| GB/T 17241.3 | 帶頸螺紋鑄鐵管法蘭 | Hubbed threaded cast iron pipe flanges |
| GB/T 17241.4 | 帶頸平焊和帶頸承插焊鑄鐵管法蘭 | Hubbed slip-on-welding and hubbed socket welding cast iron pipe flanges |
| GB/T 17241.5 | 管端翻邊帶頸松套鑄鐵管法蘭 | Loose hubbed cast iron pipe flanges for lapped pipe end |
| GB/T 17241.6 | 整體鑄鐵管法蘭 | Integral cast iron pipe flanges |
| GB/T 17241.7 | 鑄鐵管法蘭技術條件 | Specifications for cast iron pipe flanges |
| GB/T 17391 | 聚乙烯管材與管件熱穩定性試驗方法 | Test method for thermal stability of polyethylene pipes and fittings |
| GB/T 17456 | 球墨鑄鐵管外表面噴鋅涂層 | Ductile iron pipes--External zinc-spray coating |
| GB/T 17457 | 球墨鑄鐵管水泥砂漿離心法襯層一般要求 | Ductile iron pipes--Centrifugal cement mortar lining--General requirements |
| GB/T 17458 | 球墨鑄鐵管水泥砂漿離心法襯層新拌砂漿的成分檢驗 | Ductile iron pipes--Centrifugal cement mortar lining--Composition controls of freshly appliedmortar |
| GB/T 17459 | 球墨鑄鐵管瀝青涂層 | Ductile iron pipes--Bitumen coating |
| GB/T 18251 | 聚烯烴管材、管件和混配料中顏料或炭黑分散的測定方法 | Method for the assessment of pigment or carbon black dispersion in polyolefin pipes，fittings and compounds |
| GB/T 18474 | 交聯聚乙烯(PE-X)管材與管件交聯度的試驗方法 | Pipes and fittings made of crosslinked polyethylene(PE-X)--Estimation of the degree of crosslinkingby determination of the gel content |
| GB/T 18475 | 熱塑性塑料壓力管材和管件用材料分級和命名總體使用(設計)系數 | Thermoplastics materials for pipes and fittings for pressure applications classification and designation--Overall service(design) coefficient |
| GB/T 18742.3 | 冷熱水用聚丙烯管道系統第3部分:管件 | Polypropylene piping systems for hot and cold water installations--Part 3:Fittings |
| GB/T 18991 | 冷熱水系統用熱塑性塑料管材和管件 | Thermoplastics pipes and fittings forhot and cold water systems |
| GB/T 18993.3 | 冷熱水用氯化聚氯乙烯(PVC-C)管道系統第3部分: 管件 | Chlorinated poly(Vinyl chloride) piping systems for hot and cold water installations--Part 3: Fittings |
| GB/T 18998.3 | 工業用氯化聚氯乙烯(PVC-C)管道系統第3部分: 管件 | Chlorinated poly(vinyl chloride)(PVC-C) piping systems for industrial applications--Part 3: Fittings |
| GB/T 19228.1 | 不銹鋼卡壓式管件 | Stainless steel press-fittings |
| GB/T 19228.2 | 不銹鋼卡壓式管件連接用薄壁不銹鋼管 | Light gauge stainless steel pipes for stainless steel press-fittings |
| GB/T 19228.3 | 不銹鋼卡壓式管件用橡膠O形密封圈 | O-rings for stainless steel press-fittings |
| GB/T 19278 | 熱塑性塑料管材、管件及閥門通用術語及其定義 | General terms and their definitions of thermoplastic pipes，fittings and valves |
| GB/T 19473.3 | 冷熱水用聚丁烯(PB)管道系統第3部分:管件 | Polybutylene(PB) piping systems for hot and cold water installations--Part 3:Fittings |
| GB/T 19712 | 塑料管材和管件聚乙烯(PE)鞍形旁通抗沖擊試驗方法 | Plastics pipes and fittingsPolyethylene(PE) tapping tees Test method for impact resistance |
| GB/T 19806 | 塑料管材和管件聚乙烯電熔組件的擠壓剝離試驗 | Plastics pipes and fittings Crushing decohesion test for polyethylene(PE)electrofusion assemblies |
| GB/T 19807 | 塑料管材和管件聚乙烯管材和電熔管件組合試件的制備 | Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene(PE)pipe and an electrofusion fitting |
| GB/T 19808 | 塑料管材和管件公稱外徑大于或等于90mm的聚乙烯電熔組件的拉伸剝離試驗 | Plastics pipes and fittings Peel decohesion test for polyethylene(PE)electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| GB/T 19809 | 塑料管材和管件聚乙烯(PE)管材/管材或管材/管件熱熔對接組件的制備 | Plastics pipes and fittings-Preparation of polyethylene(PE)pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| GB/T 19810 | 聚乙烯(PE)管材和管件熱熔對接接頭拉伸強度和破壞形式的測定 | Polyethylene(PE)pipe and fittings-Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| GB/T 19993 | 冷熱水用熱塑性塑料管道系統 管材管件組合系統熱循環試驗方法 | Thermoplastics piping systems for hot and cold water supply-Test method for the resiance of pipes and fittings mounted assemblies to thermal cycling |
| GB/T 20201 | 灌溉用聚乙烯(PE)壓力管機械連接管件 | Mechanical joint fittings for use with polyethylene pressure pipes for irrigation purposes |
| GB/T 20207.2 | 丙烯腈－丁二烯－苯乙烯（ABS）壓力管道系統第2部分：管件 | Acrylonitrile-butadiene-styrene (ABS) pressure piping systems - Part 2: fittings |
| GB/T 20674.1 | 塑料管材和管件 聚乙烯系統熔接設備 第1部分：熱熔對接 | Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 1：Butt fusion |
| GB/T 20674.2 | 塑料管材和管件 聚乙烯系統熔接設備 第2部分：電熔連接 | Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 2: Electrofusion |
| GB/T 3287 | 可鍛鑄鐵管路連接件 | Malleable cast iron pipe fittings |
| GB/T 3420 | 灰口鑄鐵管件 | Gray iron castigs for pipe fittings |
| GB/T 3422 | 連續鑄鐵管 | Cast-iron pressure pipe made by continuous casting process |
| GB/T 5836.2 | 建筑排水用硬聚氯乙烯（PVC-U）管件 | Unplasticized poly(vinyl chloride) (PVC-U) fittings for soil and waste inside buildings |
| GB/T 6483 | 柔性機械接口灰口鑄鐵管 | Soft mechanical joint grey cast iron pipe |
| GB/T 6567.3 | 管路系統的圖形符號管件 | Graphical symbols for piping systems--Piping accessories |
| GB/T 6567.5 | 管路系統的圖形符號管路、管件和閥門等圖形符號的軸測圖畫法 | Graphical symbols for piping systems--Axonometric representation of graphical symbols for piping，piping accessories and valves etc |
| GB/T 8714 | 梯唇型橡膠圈接口鑄鐵管 | Grey cast iron pipes with rubber ring of ladder-lip-shaped |
| GB/T 8715 | 柔性機械接口鑄鐵管件 | Soft mechanical joint grey cast iron fittings |
| GB/T 8801 | 硬聚氯乙烯 (PVC-U) 管件墜落試驗方法 | Test method for unplasticized (PVC-U) fittings by falling |
| GB/T 8802 | 熱塑性塑料管材、管件維卡軟化溫度的測定 | Thermoplastics pipes and fitting--Determination of vicat softening temperature |
| GB/T 8803 | 注射成型硬質聚氯乙烯(PVC-U)、氯化聚氯乙烯(PVC-C)、丙烯腈-丁二烯-苯乙烯三元共聚物(ABS)和丙烯腈-苯乙烯 | Injection-moulded unplasticized poly(vinyl chloride)(PVC-U)，chlorinated poly(vinyl chloride)(PVC-C)，acrylonitrile butadiene-styrene(ABS)and acrylonitrile-styrene-acrylester(ASA)fittings--Hot oven test method |
| HG/T 20538 | 襯塑（PP、PE、PVC）鋼管和管件 | () |
| HG/T 20539 | 增強聚丙烯（FRPP）管子和管件 | () |
| HG/T 2128 | 耐酸酚醛塑料制化工設備、管、管件技術條件 | () |
| HG/T 21501 | 襯膠鋼管和管件 | () |
| HG/T 21561 | 丙烯腈—丁二烯—苯乙烯（ABS）管和管件 | () |
| HG/T 21562 | 襯聚四氟乙烯鋼管和管件 | () |
| HG/T 21579 | 聚丙烯/玻璃鋼（PP/FRP）復合管及管件 | () |
| HG/T 21631 | 鋼制有縫對焊管件 | () |
| HG/T 21633 | 玻璃鋼管和管件 | () |
| HG/T 21634 | 鍛鋼承插焊管件 | () |
| HG/T 21635 | 碳鋼、低合金鋼無縫對焊管件 | () |
| HG/T 21636 | 玻璃鋼/聚氯乙烯（FRP/PVC)復合管和管件 | () |
| HG/T 2435 | 玻璃管和管件 | () |
| HG/T 2436 | 玻璃管和管件耐壓試驗方法 | () |
| HG/T 2437 | 塑料襯里復合鋼管和管件 | Steel pipes and fitting lined with plastic |
| HG/T 3691 | 工業用鋼骨架聚乙稀塑料復合管件 | () |
| HG/T 3705 | 金屬網聚四氟乙烯復合管與管件 | () |
| HG/T 3707 | 工業用孔網鋼骨架聚乙烯復合管件 | () |
| HG/T 3731 | 玻璃纖維增強聚氯乙烯復合管和管件 | () |
| JB/T 1308.2 | PN250MPa閥門、管件和緊固件技術條件 | () |
| JB/T 2768 | PN16.0～32.0MPa 管子、管件、閥門端部尺寸 | () |
| JB/T 2778 | PN16.0～32.0MPa 管件和緊固件溫度標記 | () |
| JB/T 450 | PN16.0～32.0MPa 鍛造角式高壓閥門、管件、緊固件 技術條件 | () |
| JB/T 5976.1 | PNO.6MPa可鍛鑄鐵管法蘭蓋 | () |
| JB/T 5976.2 | PN1.0MPa可鍛鑄鐵管法蘭蓋 | () |
| JB/T 5976.3 | PN1.6MPa可鍛鑄鐵管法蘭蓋 | () |
| JB/T 5976.4 | PN2.5MPa可鍛鑄鐵管法蘭蓋 | () |
| JB/T 5976.5 | PN4.0MPa可鍛鑄鐵管法蘭蓋 | () |
| JB/T 5982 | 可鍛鑄鐵管法蘭用石棉橡膠墊片 | () |
| JB/T 6308 | 離心鑄管機 技術條件 | () |
| JB/T 7525 | 聚丙烯 玻璃纖維增強塑料復合管和管件 | () |
| JB/T 7870 | 噴灌用金屬薄壁管及管件 | () |
| QB/T 2003 | 食品工業用不銹鋼對縫焊接管件 | () |
| QB/T 2480 | 建筑用硬聚氯乙烯(PVC-U)雨落水管材及管件 | () |
| QB/T 3802 | 化工用硬聚氯乙烯管件 | Unplasticized polyvinyl chloride(PVC)fittings for chemical industry |
| QC/T 669-2000(2005) | 汽車空調(HFC-134a)用管接頭和管件 | () |
| SB/T 10355 | 制冷系統和熱泵—軟管件、隔振器和膨脹接頭—要求、設計與安裝 | () |
| SY/T 0510-1998(2006年確認) | 鋼制對焊管件 | () |
| SY/T 0518 | 油氣管道鋼制對焊管件設計規程 | () |
| SY/T 6266 | 低壓玻璃纖維管線管和管件 | () |
| SY/T 6701 | 增強MC尼龍管和尼龍—鋼復合管及管件 | Reinforced MC nylon pipes and nylon-steel composite pipes and fittings |
| YB/T 177-2000(2006年確認) | 連續鑄造球墨鑄鐵管 | () |
| YS/T 583 | 熱鍛水暖管件用黃銅棒 | () |
| YS/T 584 | 電極材料用鉻、鋯青銅管件 | () |
| 編號 | 中文名稱 | 英文名稱 |