微信掃一掃，立即回復！
| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| EN 10269 | 規定高溫和/或低溫性能的緊固件用鋼及鎳合金 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
| EN 1059 | 木材結構 用穿孔金屬板緊固件的預制桁架的產品要求 | Timber structures - Product requirements for prefabricated trusses using punched metal plate fasteners |
| EN 1075 | 木材結構 試驗方法 用沖擊金屬板緊固件制造的連接件 | Timber structures - Test methods - Joints made with punched metal plate fasteners |
| EN 12240 | 接觸式密合緊固件 總帶寬和有效帶寬及封閉有效寬度的測定 | Touch and close fasteners - Determination of the overall and effective widths of tapes and the effective width of a closure |
| EN 12241 | 接觸式密合緊固件 清洗、烘干和干洗之前的封閉方法 | Touch and close fasteners - Method for closure prior to washing and drying or dry cleaning |
| EN 12242 | 接觸式密合緊固件 撕裂強度的測定 | Touch and close fasteners - Determination of peel strength |
| EN 12243 | 接觸式密合緊固件 清洗、烘干和干洗中尺寸變化的測定 | Touch and close fasteners - Determination of dimensional change in washing and drying and dry cleaning |
| EN 12512 | 原木結構 試驗方法 機械緊固件形成接頭的循環試驗 | Timber structures - Test methods - Cyclic testing of joints made with mechanical fasteners |
| EN 12549 | 聲學 緊固件驅動工具的噪聲試驗規則 工程法 | Acoustics - Noise test code for fastener driving tools - Engineering method |
| EN 13780 | 觸摸式密合緊固件 縱向剪切強度的測定 | Touch and close fasteners - Determination of longitudinal shear strength |
| EN 1382 | 木材結構 試驗方法 木材緊固件的撤出能力 | Timber structures - Test methods - Withdrawal capacity of timber fasteners |
| EN 1383 | 木材結構 試驗方法 木材緊固件的抗拉性 | Timber structures - Test methods - Pull through resistance of timber fasteners |
| EN 20225 | 緊固件 螺栓、螺柱和螺母 尺寸代號和標注 | Fasteners; Bolts, screws, studs and nuts; Symbols and designation of dimensions (ISO 225:1983) |
| EN 20273 | 緊固件 螺栓和螺釘用通孔 | Fasteners; Clearance holes for bolts and screws (ISO 273:1979) |
| EN 20898-2 | 緊固件機械性能 第2部分：規定保證載荷值的螺母 粗牙螺紋 | Mechanical properties of fasteners; Part 2: Nuts with specified proof load values; Coarse thread (ISO 898-2:1992) |
| EN 20898-7 | 緊固件機械性能 第7部分：螺栓與螺釘?shù)呐ぞ卦囼?yàn)和最小扭矩公稱直徑1MM—10MM | Mechanical properties of fasteners - Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm (ISO 898-7:1992) |
| EN 26157-1 | 緊固件 表面缺陷 第1部分：螺栓、螺釘和螺柱一般要求 | Fasteners; surface discontinuities; Part 1: Bolts, srews and studs for general requirements (ISO 6157-1:1988) |
| EN 26157-3 | 緊固件 表面缺陷 第3部分：螺栓、螺釘和螺柱的特殊要求 | Fasteners; surface discontinuities; part 3: bolts, srews and studs for special requirements (ISO 6157-3:1988) |
| EN 26891 | 木材結構 機械緊固件接頭 強度和變形特性測定的一般原則 | Timber structures - Joints made with mechanical fasteners - General principles for the determination of strength and deformation characteristics (ISO 6891:1983) |
| EN 28839 | 緊固件機械性能 有色金屬制造螺栓、螺釘、螺柱和螺母 | Mechanical properties of fasteners; Bolts, screws, studs and nuts made of non-ferrous metals (ISO 8839:1986) |
| EN 28970 | 木材結構 機械緊固件接頭的試驗 對木材密度要求 | Timber structures - Testing of joints made with mechanical fasteners - Requirements for wood density (ISO 8970:1989) |
| EN 383 | 木材結構 試驗方法 榫型緊固件嵌入強度和基礎值的測定 | Timber structures - Test methods - Determination of embedding strength and foundation values for dowel type fasteners |
| EN 409 | 木材構件 試驗方法 榫型緊固件屈服力矩的測定 釘入法 | Timber structures - Test methods - Determination of the yield moment of dowel type fasteners - Nails |
| EN 493 | 緊固件 表面不均勻性 螺母 | Fasteners; Surface discontinuities; Nuts |
| EN 792-1 | 手持式非電動工具 安全要求 第1部分：非螺紋機械緊固件用組裝動力工具 | Hand-held non-electric power tools - Safety requirements - Part 1: Assembly power tools for non-threaded mechanical fasteners |
| EN 792-13 | 手持式非電動工具 安全要求 第13部分：緊固件傳動工具 | Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving tools |
| EN 792-6 | 手持式非電動工具 安全要求 第6部分：螺紋緊固件用組裝動力工具 | Hand-held non-electric power tools - Safety requirements - Part 6: Assembly power tools for threaded fasteners |
| EN 912-1999+AC | 木材緊固件 木材連接器規范 | Timber fasteners - Specifications for connectors for timber |
| EN ISO 10683 | 緊固件 非電解鋅粉覆蓋層 | Fasteners - Non-electrolytically applied zinc flake coatings (ISO 10683:2000) |
| EN ISO 10964 | 粘合劑 螺紋緊固件上厭氧粘合劑的抗扭強度的測定 | Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993) |
| EN ISO 12777-1 | 托盤連接件的試驗方法 第1部分：托盤用釘子、其他榫釘型緊固件和U形釘?shù)目箯澰囼?yàn) | Methods of test for pallet joints - Part 1: Determination of bending resistance of pallet nails, other dowel-type fasteners and staples (ISO 12777-1:1994) |
| EN ISO 15330 | 緊固件 檢查氫脆用預載荷試驗 平行支承面法 | Fasteners - Preloading test for the detection of hydrogen embrittlement - Parallel bearing surface method (ISO 15330:1999) |
| EN ISO 16048 | 耐蝕不銹鋼緊固件的鈍化 | Passivation of corrosion-resistant stainless steel fasteners (ISO 16048:2003) |
| EN ISO 16426 | 緊固件 質量保證體系 | Fasteners - Quality assurance system (ISO 16426:2002) |
| EN ISO 3269 | 緊固件 驗收檢查 | Fasteners - Acceptance inspection (ISO 3269:2000) |
| EN ISO 3506-1 | 耐腐蝕不銹鋼緊固件的機械性能 第1部分：螺栓、螺釘和螺柱 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:1997) |
| EN ISO 3506-2 | 耐腐蝕不銹鋼緊固件的機械性能 第2部分：螺母 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 2: Nuts (ISO 3506-2:1997) |
| EN ISO 3506-3 | 耐腐蝕不銹鋼緊固件的機械性能 第3部分：緊定螺釘及類似的不受應力的螺紋緊固件 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:1997) |
| EN ISO 3506-4 | 耐腐蝕不銹鋼緊固件的機械性能 第4部分：自攻螺釘 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 4: Tapping screws (ISO 3506-4:2003) |
| EN ISO 4042 | 緊固件 電鍍層 | Fasteners - Electroplated coatings (ISO 4042:1999) |
| EN ISO 4753 | 緊固件 ISO米制外螺紋零件的末端 | Fasteners - Ends of parts with external ISO metric screw thread (ISO 4753:1999) |
| EN ISO 4759-1 | 緊固件公差 第1部分：螺栓、螺釘、螺柱和螺母 產品等級A、B和C級 | Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts; product grades A, B and C (ISO 4759-1:2000) |
| EN ISO 4759-3 | 緊固件公差 第3部分：螺栓、螺釘和螺母用平墊圈 產品等級A和C級 | Tolerances for fasteners - Part 3: Plain washers for bolts, screws and nuts - Product grades A and C (ISO 4759-3:2000) |
| EN ISO 5845-1 | 技術制圖 緊固件組合的簡單表示法 第1部分：一般原則 | Technical drawings - Simplified representation of the assembly of parts with fasteners - Part 1: General principles (ISO 5845-1:1995) |
| EN ISO 898-1 | 碳鋼和鑄鋼鑄造的緊固件機械性能 第1部分：螺栓、螺釘和螺柱 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs (ISO 898-1:1999) |
| EN ISO 898-5 | 碳鋼和鑄鋼鑄造的緊固件機械性能 第5部分：緊定螺釘及類似的不受拉應力的螺紋緊固件 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners not under tensile stresses (ISO 898-5:1998) |
| EN ISO 898-6 | 緊固件機械性能 第6部分：規定保證載荷值的螺母 細牙螺紋 | Mechanical properties of fasteners - Part 6: Nuts with specified proof load values - Fine pitch thread (ISO 898-6:1994) |
| prEN 1660 | 機械緊固件 六角產品 對邊寬度 | Mechanical fasteners - Hexagon products - Widths across flats |
| prEN 2098-6 | 航空航天系列 鈦及耐熱合金鍛制產品的檢驗和試驗要求 第6部分：棒材和線材緊固件的檢驗和試驗要求 | Aerospace series; inspection and testing requirements for titanium and heat resisting alloy wrought products; part 6: inspection and testing requirements for bars and wires fasteners |
| prEN 2959 | 航空航天系列 NI-PH1302 (NiCr20Co13Mo4Ti3Al)耐熱合金固溶處理和冷加工 鍛造緊固件用棒材3 mm≤D≤30 mm | Aerospace series - Heat resisting alloy NI-PH1302 (NiCr20Co13Mo4Ti3Al) - Solution treated and cold worked - Bar for forged fasteners 3 mm D 30 mm |
| prEN 4603 | 航空航天系列 緊固件的二硫化鉬涂層 技術規范 | Aerospace series - Molybdenum disulphide coatings of fasteners - Technical specification |
| prEN 792-14 | 手持式非電動工具 安全要求 第14部分：非螺紋機械緊固件用組裝動力工具 | Hand-held non electric power tools - Safety requirements - Part 14: Assembly power tools for non-threaded mechanical fasteners |
| 編號 | 中文名稱 | 英文名稱 |