標準號 |
中文名稱 |
英文名稱 |
| ANSI/ASTM D 350-1997 |
電絕緣用經處理軟套管的試驗方法 |
Test Methods for Flexible Treated Sleeving Used for Electrical Insulation |
| ANSI/ASTM D 3517-2001 |
纖維玻璃(玻璃纖維增強熱固樹脂)規范(08.04) |
Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting Resin)(08.04) |
| ANSI/ASTM D 3519-1988 |
含水介質中泡沫的試驗方法(混合試驗)(05.02) |
Foam in Aqueous Media (Blender Test), Test Method for (05.02) |
| ANSI/ASTM D 3521-1986 |
波紋紙板上表面蠟涂層的試驗(05.02) |
Corrugated Board, Test for Surface Wax Coating on (05.02) |
| ANSI/ASTM D 3522-1986 |
涂蠟和浸漬蠟于波紋紙板表面上的試驗(05.02) |
Corrugated Board Facing, Test for Applied Coating Wax and Impregnating Wax in (05.02) |
| ANSI/ASTM D 3523-1992 |
液體和固體的自身加熱值的試驗(差動麥克試驗)(05.02) |
Liquids and Solids (Differential Mackey Test), Test for Spontaneous Heating Values of (05.02) |
| ANSI/ASTM D 3524-1990 |
用氣相色譜法測定用過的柴油機油中柴油燃料稀釋劑的試驗(05.02) |
Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography, Test for (05.02) |
| ANSI/ASTM D 3525-1990 |
用氣相色譜法測定用過的氣油機油中氣油稀釋劑的試驗(05.02) |
Gasoline Diluent in Used Gasoline Engine Oils by Gas Chromatography, Test for (05.02) |
| ANSI/ASTM D 3527-1988 |
機動車輪軸承潤滑脂的壽命性能的試驗(05.02) |
Life Performance of Automotive Wheel Bearing Grease, Test for (05.02) |
| ANSI/ASTM D 3561-2002 |
用離子吸收光譜法測試微咸水、海水和鹽水中的鋰、鉀和鈉離子的方法 |
Test Method for Lithium, Potassium, and Sodium Ions in Brackish Water, Seawater, and Brines by Atomic Absorption Spectrophotometry |
| ANSI/ASTM D 3567-1991 |
增強熱固樹脂管和配件的尺寸的測定方法(08.04) |
Practice for Determining Dimensions of Reinforced Thermosetting Resin Pipe (RTRP) and Fittings (08.04) |
| ANSI/ASTM D 3575-2001 |
由烯烴聚合物生產的柔性多孔材料的試驗方法 |
Test Methods for Flexible Cellular Materials Made from Olefin Polymers |
| ANSI/ASTM D 3576-1994 |
硬質多孔塑料的孔徑的試驗方法(08.02) |
Test Method for Cell Size of Rigid Cellular Plastics (08.02) |
| ANSI/ASTM D 3590-2002 |
水中克耶達(Kjeldahl)氮總含量的試驗方法 |
Test Methods for Total Kjeldahl Nitrogen in Water |
| ANSI/ASTM D 3595-1991 |
聚三氟氯乙烯擠塑薄板和薄膜規范(08.03) |
Specification for Polychlorotrifluoroethylene (PCTFE) Extruded Plastic Sheet and Film (08.03) |
| ANSI/ASTM D 3596-2001 |
通用聚氯乙烯樹脂中凝膠的實施規程(08.03) |
Practice for Determination of Gels (Fisheyes) in General-Purpose Poly(Vinyl Chloride) (PVC) Resins |
| ANSI/ASTM D 3601-1988 |
含水介質中的泡沫(瓶試驗)方法(05.02) |
Foam in Aqueous Media (Bottle Test), Test Method for (05.02) |
| ANSI/ASTM D 3602-1990 |
航空渦輪燃料的水分離特性(現場試驗)試驗(05.02) |
Water Separation Characteristics of Aviation Turbine Fuels (Field Test), Test for (05.02) |
| ANSI/ASTM D 3603-1993 |
在有水的情況下蒸氣渦輪油的防銹特性試驗方法(臥式圓盤法)(05.02) |
Rust-Preventing Characteristics of Steam Turbine Oil in the Presence of Water (Horizontal Disk Method), Test for (05.02) |
| ANSI/ASTM D 3605-1991 |
用原子吸收和噴焰光譜法測定燃氣渦輪機燃料中痕量金屬的試驗方法(05.02) |
Test Method for Trace Metals in Gas Turbine Fuels by Atomic Absorption and Flame Emission Spectroscopy (05.02) |
| ANSI/ASTM D 3606-1992 |
用氣相色譜法測定機動車和航空用汽油中苯和甲苯的試驗方法(05.02) |
Test Method for Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography (05.02) |
| ANSI/ASTM D 3607-1985 |
用剝離法除去用過的機油中揮發性污物的試驗方法(05.02) |
Removing Volatile Contaminants from Used Engine Oils by Stripping (05.02) |
| ANSI/ASTM D 3609-2001 |
滲透管校準技術的實施規程 |
Practice for Calibration Techniques Using Permeation Tubes |
| ANSI/ASTM D 3614-1990 |
實驗室進行抽樣、空氣分析和排放的指南 |
Guide for Laboratories Engaged in Sampling and Analysis of Atmospheres and Emissions |
| ANSI/ASTM D 3631-2001 |
測量表面大氣壓的試驗方法 |
Test Methods for Measuring Surface Atmospheric Pressure |
| ANSI/ASTM D 3634-1999 |
測定發動機冷卻劑中痕量氯離子的試驗方法 |
Test Method for Trace Chloride Ion in Engine Coolants |
| ANSI/ASTM D 3636-1995 |
實心絕緣材料的抽樣和質量評定(05.02) |
Sampling and Judging Quality of Solid Electrical Insulating Materials (10.02) |
| ANSI/ASTM D 3651-2002 |
微咸水、海水和鹽水中的鋇離子的測試方法 |
Test Method for Barium in Brackish Water, Seawater, and Brines |
| ANSI/ASTM D 3675-2001 |
用輻射熱能源測定柔性多孔材料的表面易燃性的試驗方法 |
Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ANSI/ASTM D 3676-2001 |
地毯或地毯墊襯用橡膠多孔墊層規范 |
Specification for Rubber Cellular Cushion Used for Carpet or Rug Underlay |
| ANSI/ASTM D 3678-2001 |
硬質聚氯乙烯內定形擠壓件規范 |
Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior Profile Extrusions (08.04) |
| ANSI/ASTM D 3679-1995 |
硬質聚氯乙烯邊緣修整規范(08.04) |
Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding (08.04) |
| ANSI/ASTM D 368-1996 |
雜酚油及油質防腐劑比重的試驗方法 |
Test Method for Specific Gravity of Creosote and Oil-Type Preservatives |
| ANSI/ASTM D 3681-2001 |
在偏轉條件下纖維玻璃(玻璃纖維增強樹脂)管耐化學性的試驗方法(08.04) |
Test Method for Chemical Resistance of Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe in a Deflected Condition (08.04) |
| ANSI/ASTM D 3685/D 3685M-2001 |
煙氣中顆粒物的取樣和測定的試驗方法 |
Test Methods for Sampling and Determination of Particulate Matter in Stack Gases |
| ANSI/ASTM D 3687-2001 |
用活性碳管吸收法收集的有機化合物蒸汽的分析規程 |
Practice for Analysis of Organic Compound Vapors Collected by the Activated Charcoal Tube Adsorption Method |
| ANSI/ASTM D 369-1996 |
雜酚油餾份與殘渣比重的測試方法 |
Test Method for Specific Gravity of Creosote Fractions and Residues |
| ANSI/ASTM D 3698-1996 |
溶劑蒸氣脫脂操作實施規程 |
Practice for Solvent Vapor Degreasing Operations |
| ANSI/ASTM D 3699-1992 |
煤油規范(05.02) |
Kerosine, Specification for (05.02) |
| ANSI/ASTM D 370-1996 |
油質防腐劑脫水作用的試驗方法 |
Test Method for Dehydration of Oil-Type Preservatives |
| ANSI/ASTM D 3700-2001 |
用浮動活塞缸獲取液態烴樣品的試驗 |
Hydrocarbon Fluid Samples Using a Floating Piston Cylinder, Test for Obtaining (05.02) |
| ANSI/ASTM D 3701-2001 |
低分辨核磁共振光譜法測定航空渦輪機燃料中氫含量的試驗方法 |
Test Method for Hydrogen Content of Aviation Turbine Fuels by Low Resolution Nuclear Magnetic Resonance Spectrometry (05.02) |
| ANSI/ASTM D 3702-1994 |
用止推墊圈試驗機測定在非潤滑摩擦接觸中材料的磨損率的試驗(05.02) |
Wear Rate of Materials in Unlubricated Rubbing Contact Using a Thrust Washer Testing Machine, Test for (05.02) |
| ANSI/ASTM D 3703-1992 |
航空渦輪燃料的過氧化物的數量的試驗(05.02) |
Peroxide Number of Aviation Turbine Fuels, Test for (05.02) |
| ANSI/ASTM D 3704-1990 |
在震蕩運動中用潤滑劑耐熱耐壓試驗機測定潤滑脂的耐磨損特性的試驗(05.02) |
Wear Preventive Properties of Lubrication Greases Using the (Falex) Ring and Block Test Machine in Oscillating Motion, Test for (05.02) |
| ANSI/ASTM D 3707-1989 |
用烘爐試驗法測定油中含水乳液的存儲穩定性的試驗方法(05.02) |
Storage Stability of Water-in-Oil Emulsions by the Oven Test Method, Test Method for (05.02) |
| ANSI/ASTM D 3709-1989 |
低于室溫循環條件下的油中含水乳液的穩定性的試驗方法(05.02) |
Stability of Water-in-Oil Emulsions Under Low to Ambient Temperature Cycling Conditions, Test Method for (05.02) |
| ANSI/ASTM D 3710-1988 |
用氣相色譜法測定汽油和汽油餾份的沸點范圍分布的試驗方法(05.02) |
Boiling Range Distribution of Gasoline and Gasoline Fractions by Gas Chromatography, Test Method for (05.02) |
| ANSI/ASTM D 3711-1995 |
薄膜液體和蒸氣的沉積趨勢的試驗方法(05.02) |
Test Method for Deposition Tendencies of Liquids in Thin Films and Vapors (05.02) |
| ANSI/ASTM D 3712-1991 |
用液相色譜法分析可溶性石油硫化鹽的方法(05.02) |
Method for Analysis of Oil-Soluble Petroleum Sulfonates by Liquid Chromatography (05.02) |
| ANSI/ASTM D 374-1994 |
固體電絕緣材料厚度的測試方法 |
Test Methods for Thickness of Solid Electrical Insulation (10.01) |
| ANSI/ASTM D 3748-1994 |
評價高密度硬性多孔熱塑料的實施規程(08.02) |
Practice for Evaluating High Density Rigid Cellular Thermoplastics (08.02) |
| ANSI/ASTM D 3749-1995 |
用液上氣相色譜法測定聚乙烯樹脂中殘留乙烯單體的試驗方法(08.03) |
Test Method for Residual Vinyl Chloride Monomer in Poly (Vinyl Chloride) Resins by Gas Chromatographic Headspace Technique (08.03) |
| ANSI/ASTM D 374M-1994 |
固體電絕緣材料厚度的測試方法(米制) |
Test Methods for Thickness of Solid Electrical Insulation (Metric) (10.01) |
| ANSI/ASTM D 3754-2001 |
纖維玻璃污水管和工業用壓力管規范(08.04) |
Specification for Fiberglass Sewer and Industrial Pressure Pipe (08.04) |
| ANSI/ASTM D 3763-1986 |
用載荷-位移傳感器測定塑料的高速刺穿特性的試驗方法(08.03) |
Plastics Using Load and Displacement Sensors, Test Method for High-Speed Puncture Properties of (08.03) |
| ANSI/ASTM D 3764-2001 |
工業生產液流分析儀校驗的實施規范 |
Validation of Process Stream Analyzers, Practice for (05.02) |
| ANSI/ASTM D 3795-1980 |
用轉矩流變儀測定熱固性塑料的熱流量和固化特性的試驗方法(15.04) |
Test Method for Thermal Flow and Cure Properties of Thermosetting Plastics by Torque Rheometer (15.04) |
| ANSI/ASTM D 3796-1990 |
S型皮氏流量測定管的校準實施規程 |
Practice for Calibration of Type-S Pitot Tubes |
| ANSI/ASTM D 381-2001 |
用射流蒸發法測定燃料中現存煤末的試驗方法 |
Existent Gum in Fuels by Jet Evaporation, Method of Test for (05.01) |
| ANSI/ASTM D 3825-1990 |
用快速發泡技術測定動態表面張力的試驗方法(15.02) |
Test Method for Dynamic Surface Tension by the Fast Bubble Technique (15.02) |
| ANSI/ASTM D 3826-1998 |
用張力測定可降解的聚烯烴中降解末端點的實施規程 |
Practice for Determining Degradation End Point in Degradable Polyolefins Using a Tensile |
| ANSI/ASTM D 3827-1992 |
石油和其他有機液體中氣體的可溶解性的評估方法(05.02) |
Solubility of Gases in Petroleum and Other Organic Liquids, Method for Estimation of (05.02) |
| ANSI/ASTM D 3828-1987 |
用Setaflash閉合試驗機測定閃點的試驗(05.02) |
Flash Point by Setaflash Closed Tester, Test for (05.02) |
| ANSI/ASTM D 3829-1993 |
機油的邊界泵送溫度的預測試驗(05.02) |
Predicting the Borderline Pumping Temperature of Engine Oil, Test for (05.02) |
| ANSI/ASTM D 3831-2001 |
用原子吸收光譜測定法測定汽油中錳的含量的試驗(05.02) |
Manganese in Gasoline by Atomic Absorption Spectrometry, Test for (05.02) |
| ANSI/ASTM D 3835-1995 |
用毛細管流變器測定熱塑料的流變性能的試驗方法(08.03) |
Test Method for Measuring the Rheological Properties of Thermoplastics with a Capillary Rheometer (08.03) |
| ANSI/ASTM D 3840-2001 |
非壓力下用增強塑料砂漿管配件規范(08.04) |
Specification for Reinforced Plastic Mortar Pipe Fittings for Non-Pressure Applications (08.04) |
| ANSI/ASTM D 3841-2001 |
玻璃纖維增強聚酯塑料板規范 |
Specification for Glass Fiber-Reinforced Polyester Plastic Panels (08.04) |
| ANSI/ASTM D 3844-1996 |
鹵化烴溶劑容器標記實施規程 |
Practice for Labeling Halogenated Hydrcarbon Solvent Containers |
| ANSI/ASTM D 3850-1994 |
熱重分析儀對固體電絕緣材料快速熱降解的試驗方法 |
Test Method for Rapid Thermal Degradation of Solid Electrical Insulating Materials by Thermogravimetric Method (10.02) |
| ANSI/ASTM D 3856-1995 |
水取樣和分析實驗室中良好實驗室實施規程指南 |
Guide for Good Laboratory Practices in Laboratories Engaged in Sampling and Analysis of Water |
| ANSI/ASTM D 3861-1998 |
薄膜過濾器中水的可萃取物質量的試驗方法 |
Test Method for Quantity of Water-Extractable Matter in Membrane Filters |
| ANSI/ASTM D 3864-1996 |
水分析連續在線監測系統指南 |
Guide for Continual On-Line Monitoring Systems for Water Analysis |
| ANSI/ASTM D 3865-2002 |
水中钚的試驗方法 |
Test Method for Plutonium in Water |
| ANSI/ASTM D 3866-2002 |
水中銀的試驗方法 |
Test Methods for Silver in Water |
| ANSI/ASTM D 3873-2001 |
氨銅砷酸鹽溶液的砷化合物化合價狀態的試驗方法 |
Test Method for Valency State of the Arsenic Component of Ammoniacal Copper Arsenate Solutions |
| ANSI/ASTM D 3894-1988 |
用小角結構對硬質多孔塑料耐火性能的評定方法 |
Method for Evaluation of Fire Response of Rigid Cellular Plastics Using a Small Corner Configuration (08.03) |
| ANSI/ASTM D 3895-1995 |
差別掃描量熱法測定聚烯烴氧化感應時間的試驗方法 |
Test Method for Oxidative Induction Time of Polyolefins by Thermal Analysis (08.03) |
| ANSI/ASTM D 390-1996 |
海上、陸地及淡水中用木樁、電桿和木材的防腐處理用煤焦油雜酚油規范 |
Specification for Coal-Tar Creosote for the Preservative Treatment of Piles, Poles, and Timbers of Marine, Land, and Fresh Water Use |
| ANSI/ASTM D 3904-1990 |
從油頁巖中提取油的試驗方法(用USBM費歇爾分析法) |
Test Method for Oil from Oil Shale (Resource Evaluation by the USBM Fischer Assay Procedure) (05.02) |
| ANSI/ASTM D 3915-1992 |
壓力塑料管和配件用剛性聚氯乙烯(PVC)和氯化聚氯乙烯復合物規范 |
Specification for Poly (Vinyl Chloride) (PVC) and Related Plastic Pipe and Fitting Compounds (08.04) |
| ANSI/ASTM D 3916-1994 |
擠拔玻璃纖維增強塑料棒張力特性的試驗方法 |
Test Method for Tensile Properties of Pultruded Glass Fiber-Reinforced Plastic Rod (08.02) |
| ANSI/ASTM D 3917-1994 |
熱固玻璃纖維增強塑料擠拔型材的尺寸公差規格 |
Specification for Dimensional Tolerance of Thermosetting Glass-Reinforced Plastic Pultruded Shapes (08.02) |
| ANSI/ASTM D 3935-1994 |
聚碳酸酯非填充和加固材料規范 |
Specification for Polycarbonate (PC) Unfilled and Reinforced Materials (08.02) |
| ANSI/ASTM D 3944-1988 |
石油蠟凝點 |
Solidification Point of Petroleum Wax (05.02) |
| ANSI/ASTM D 3945-1986 |
用柴油機噴嘴對含有液體聚合物的剪切應力穩定性的試驗方法 |
Shear Stability of Polymer-Containing Fluids, Using a Diesel Injection Nozzle, Test Method for (05.02) |
| ANSI/ASTM D 3946-1992 |
評價餾出水金屬加工液抗菌性的試驗方法 |
Bioresistance of Water-Soluble Metal-Working Fluids (05.02) |
| ANSI/ASTM D 3948-1987 |
用便攜式分類計測定航空燃氣渦輪發動機用燃料脫水特性的試驗方法 |
Water Separation Characteristics of Aviation Turbine Fuels by Portable Separometer, Field Test Method for (05.02) |
| ANSI/ASTM D 3949-1994 |
電絕緣用涂覆玻璃織物規范 |
Specification for Coated Glass Fabrics Used for Electrical Insulation (10.02) |
| ANSI/ASTM D 3955-1995 |
電氣絕緣清漆規范 |
Specification for Electrical Insulating Varnishes (10.02) |
| ANSI/ASTM D 396-1992 |
燃料油規范 |
Fuel Oils, Specification for (05.01) |
| ANSI/ASTM D 3965-1994 |
管和配件用剛性丙烯腈-丁二烯-苯乙烯共聚物規格 |
Specification for Rigid Acrylonitrile Butadiene-Styrene (ABS) Compounds for Pipe and Fittings (08.03, 08.04) |
| ANSI/ASTM D 3972-2002 |
用放射化學法進行水中同位素鈾的試驗方法 |
Test Method for Isotopic Uranium in Water by Radiochemistry |
| ANSI/ASTM D 3975-1999 |
沉積物分析方法的聯合實驗室試驗用樣品的研發與使用(制備)實施規程 |
Practice for Development and Use (Preparation) of Samples for Collaborative Testing of Methods for Analysis of Sediments |
| ANSI/ASTM D 3976-1996 |
化學分析用沉積樣品制備的實施規程 |
Practice for Preparation of Sediment Samples for Chemical Analysis |
| ANSI/ASTM D 3981-1989 |
通用和包裝用中密度聚乙烯薄膜規格 |
Specification for Medium-Density Polyethylene Films for General Use and Packaging Applications (08.03) |
| ANSI/ASTM D 3982-1992 |
常規接觸壓模制玻璃纖維增強熱固樹脂護罩規格 |
Specification for Custom Contact-Pressure-Molded Glass-Fiber-Reinforced Thermosetting Resin Hoods (08.04) |
| ANSI/ASTM D 4000-1991 |
特殊用途塑料材料的分類系統 |
Classification System for Specifying Plastic Materials (08.03) |
| ANSI/ASTM D 4006-1981 |
用蒸餾法測定原油中的水含量 |
Water in Crude Oil by Distillation (05.03) |
| ANSI/ASTM D 4007-1981 |
用離心法測定原油中水和沉淀物的含量(實驗室法) |
Water and Sediment in Crude Oil by the Centrifuge Method (Laboratory Procedures) (05.02) |
| ANSI/ASTM D 4019-1994 |
通過電量測定法對塑料中潮氣的試驗方法 |
Test Method for Moisture in Plastics by Coulometry (08.03) |
| ANSI/ASTM D 4020-1992 |
超高分子聚乙烯模壓和擠壓材料的規格 |
Specification for Ultra-High-Molecular-Weight Polyethylene Molding and Extrusion Materials (08.02) |
| ANSI/ASTM D 4024-1994 |
機器造纖維玻璃法蘭規范 |
Specification for Reinforced Thermosetting Resin (Rtr) Flanges (08.04) |
| ANSI/ASTM D 4025-2001 |
地下注入水形成沉積物的檢驗和分析報告結果的實施規程 |
Practice for Reporting Results of Examination and Analysis of Deposits Formed from Water for Subsurface Injection |
| ANSI/ASTM D 4042-1992 |
碾油軋鋼機擴散體中粉塵和總含鐵量的取樣及試驗 |
Rolling Oils, Sampling and Testing for Ash and Total Iron in Steel Mill Dispersions of (05.03) |
| ANSI/ASTM D 4045-1992 |
利用氫解作用和速率計的色度術測試石油產品中的硫 |
Sulfur in Petroleum Products by Hydrogenolysis and Rateometric Colorimetry (05.02) |
| ANSI/ASTM D 4046-1991 |
用分光光度法對柴油機燃料中烷基硝酸鹽的試驗方法 |
Test Method for Alkyl Nitrate in Diesel Fuels by Spectrophotometry (05.02) |
| ANSI/ASTM D 4047-1991 |
用喹啉磷鉬酸鹽法對潤滑油及添加劑中磷含量的試驗方法 |
Test Method for Phosphorus in Lubricating Oils and Additives by Quinoline Phosphomolybdate Method (05.02) |
| ANSI/ASTM D 4048-1991 |
用銅帶生銹試驗檢測潤滑油對銅腐蝕的方法 |
Method for Detection of Copper Corrosion from Lubricating Grease by the Copper Strip Tarnish Test (05.02) |
| ANSI/ASTM D 4049-1993 |
潤滑脂耐水噴灑性的試驗方法 |
Resistance of Lubricating Grease to Water Spray, Test Method for (05.02) |
| ANSI/ASTM D 4051-1989 |
低壓氣體混合物制備方法 |
Preparation of Low-Pressure Gas Blends, Method for (05.02) |
| ANSI/ASTM D 4052-1996 |
用數字式密度計測定液體密度和相對密度的試驗方法 |
Test Method for Density and Relative Density of Liquids by Digital Density Meter (05.02) |
| ANSI/ASTM D 4053-1991 |
用火焰分光光度計對機動車和航空汽油中苯的試驗方法 |
Test Method for Benzene in Motor and Aviation Gasoline by Infrared Spectroscopy (05.02) |
| ANSI/ASTM D 4054-1981 |
添加航空渦輪燃料和飛行器燃料系統材料的兼容性評價 |
Evaluating the Compatability of Additives with Aviation Turbine Fuels and Aircraft Fuel System Materials (05.02) |
| ANSI/ASTM D 4055-2001 |
薄膜過濾法測定戊烷不溶性 |
Pentane Insolubles by Membrane Filtration (05.02) |
| ANSI/ASTM D 4056-2001 |
烴類和脂肪族脂化潤滑劑中水的可溶性 |
Solubility of Water in Hydrocarbon and Aliphatic Ester Lubricants (05.02) |
| ANSI/ASTM D 4057-1988 |
石油及石油產品人工取樣 |
Manual Sampling of Petroleum and Petroleum Products (05.02) |
| ANSI/ASTM D 4064-2001 |
通過熱過程對功能孔的保存處理的操作規程 |
Practice for Preservative Treatment of Utility Poles by the Thermal Process |
| ANSI/ASTM D 4065-2001 |
塑料動態機械特性測定和報告規程 |
Practice for Determining and Reporting Dynamic Mechanical Properties of Plastics (08.03) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com