標準號 |
中文名稱 |
英文名稱 |
| DIN IEC 60384-2-1991 |
電子設備用固定電容器.第2部分:分規范:金屬化聚乙烯對苯二甲酸乙二酸脂薄膜介質直流固定電容器 |
Fixed capacitors for use in electronic equipment; part 2: sectional specification: fixed metallized polyethylene-terephthalate film dielectric direct current capacitors; identical with IEC 60384-2:1982 (status as of 1987) |
| DIN IEC 60384-3-1-1991 |
電子設備用固定電容器.第3部分:分規范:固定式鉭片電容器.第1節:空白詳細規范:固定式鉭片電容器.E級評定 |
Fixed capacitors for use in electronic equipment; part 3: blank detail specification: fixed tantalum chip capacitors; assessment level E; identical with IEC 60384-31:1989 |
| DIN IEC 60384-3-1991 |
電子設備用固定電容器.第3部分:分規范:固定式鉭片電容器 |
Fixed capacitors for use in electronic equipment; part 3: sectional specification: fixed tantalum chip capacitors; identical with IEC 60384-3:1989 |
| DIN IEC 60384-4-1-1991 |
電子設備用固定電容器.第4部分:分規范:固體或非固體電解質鋁電解電容器.第1節:空白詳細規范:非固體電解質鋁電解電容器.E級評定 |
Fixed capacitors for use in electronic equipment; blank detail specification: aluminium electrolytic capacitors with non-solid electrolyte, assessment level E; identical with IEC 60384-4-1:1985 |
| DIN IEC 60384-4-1991 |
電子設備用固定電容器.第4部分:分規范:固體或非固體電解質鋁電解電容器 |
Fixed capacitors for use in electronic equipment; sectional specification: aluminium electrolytic capacitors with solid and non-solid electrolyte; identical with IEC 60384-4:1985 |
| DIN IEC 60384-4-2-1991 |
電子設備用固定電容器.第4部分:分規范:固體或非固體電解質鋁電解電容器.第2節:空白詳細規范:固體電解質鋁電解電容器.E級評定 |
Fixed capacitors for use in electronic equipment; blank detail specification: aluminium electrolytic capacitors with solid electrolyte, assessment level E; identical with IEC 60384-4-2:1985 |
| DIN IEC 60384-5-1-1994 |
電子設備用固定電容器.第5部分:額定電壓不超過3000V的固定式直流云母電容器.第1節:E級評定 |
Fixed capacitors for use in electronic equipment; part 5: blank detail specification: fixed mica dielectric d.c. capacitors with a rated voltage not exceeding 3000 V; assessment level E; identical with IEC 60384-5-1:1993 |
| DIN IEC 60384-5-1994 |
電子設備用固定電容器.第5部分:分規范:額定電壓不超過3000V的固定式直流云母電容器.試驗方法的選擇和一般要求 |
Fixed capacitors for use in electronic equipment; part 5: sectional specification: fixed mica dielectric d.c. capacitors with a rated voltage not exceeding 3000 V; selection of methods of test general requirements; identical with IEC 60384-5:1993 |
| DIN IEC 60384-6-1-1992 |
電子設備用固定電容器.第6部分:分規范:固定金屬化聚碳酸酯薄膜介質直流電容器.空白詳細規范:固定金屬化聚碳酸酯薄膜介質直流電容器.E級評定 |
Fixed capacitors for use in electronic equipment; part 6: blank detail specification: fixed metallized polycarbonate film dielectric direct current capacitors; assessment level E; identical with IEC 60384-6-1:1987 |
| DIN IEC 60384-6-1992 |
電子設備用固定電容器.第6部分:分規范:固定金屬化聚碳酸酯薄膜直流電容器 |
Fixed capacitors for use in electronic equipment; part 6: sectional specification: fixed metallized polycarbonate film dielectric direct current capacitors; identical with IEC 60384-6:1987 |
| DIN IEC 60384-7-1-1992 |
電子儀器用固定電容器.第7部分:空白詳細規范:固定聚苯乙烯薄膜絕緣金屬箔直流電容器.第1節:E級評定 |
Fixed capacitors for use in electronic equipment; part 7: blank detail specification: fixed polystyrene film dieletric metal foil d.c. capacitors; assessment level E; identical with IEC 60384-7-1:1991 |
| DIN IEC 60384-7-1992 |
電子儀器用固定電容器.第7部分:分規范:固定聚苯乙烯薄膜絕緣金屬箔直流電容器 |
Fixed capacitors for use in electronic equipment; part 7: sectional specification: fixed polystyrene film dieletric metal foil d.c. capacitors; identical with IEC 60384-7:1991 |
| DIN IEC 60384-8-1-1993 |
電子設備用固定電容器.第8部分:空白詳細規范.1級陶瓷介質固定電容器.E級質量評定 |
Fixed capacitors for use in electronic equipment; part 8: blank detail specification: fixed capacitors of ceramic dielectric, class 1; assessment level E; identical with IEC 60384-8-1:1988 |
| DIN IEC 60384-8-1993 |
電子設備用固定電容器.第8部分:分規范:1級陶瓷介質固定電容器 |
Fixed capacitors for use in electronic equipment; part 8: sectional specification: fixed capacitors of ceramic dielectric, class 1; identical with IEC 60384-8:1988 |
| DIN IEC 60384-9-1-1993 |
電子設備用固定電容器.第9部分:空白詳細規范.2級陶瓷介質固定電容器.E級質量評定 |
Fixed capacitors for use in electronic equipment; part 9: blank detail specification: fixed capacitors of ceramic dielectric, class 2; assessment level E; identical with IEC 60384-9-1:1988 |
| DIN IEC 60384-9-1993 |
電子設備用固定電容器.第9部分:分規范.2級陶瓷介質固定電容器 |
Fixed capacitors for use in electronic equipment; part 9: sectional specification: fixed capacitors of ceramic dielectric, class 2; identical with IEC 60384-9:1988 |
| DIN IEC 60386-1995 |
錄音和放音設備速度波動的測量方法 |
Method of measurement of speed fluctuations in sound recording and reproducing equipment (IEC 60386:1972 + A1:1988) |
| DIN IEC 60393-1-1998 |
電子設備使用的電位器.第1部分:總規范 |
Potentiometers for use in electronic equipment - Part 1: Generic specification (IEC 60393-1:1989 + A1:1992) |
| DIN IEC 60393-1-1998 |
電子設備使用的電位器.第1部分:總規范 |
Potentiometers for use in electronic equipment - Part 1: Generic specification (IEC 60393-1:1989 + A1:1992) |
| DIN IEC 60393-1-1998 |
電子設備使用的電位器.第1部分:總規范 |
Potentiometers for use in electronic equipment - Part 1: Generic specification (IEC 60393-1:1989 + A1:1992) |
| DIN IEC 60396-1994 |
槽式感應爐的試驗方法 |
Test methods for induction channel furnaces (IEC 60396:1991); German version HD 610 S1:1992 |
| DIN IEC 60404-12-1999 |
磁性材料.第12部分:絕緣層溫度穩定性評定方法指南 |
Magnetic materials - Part 12: Guide to methods of assessment of temperature capability of interlaminar insulation coatings (IEC 60404-12:1992) |
| DIN IEC 60404-7-1985 |
磁性材料.第7部分:開磁路中磁性材料矯頑力的測量方法 |
Magnetic materials; part 7: method of measurement of the coereivity of magnetic materials in an open circuit |
| DIN IEC 60404-8-1-2003 |
磁性材料.第8-1部分:單項材料規范.磁性硬質材料 |
Magnetic materials - Part 8-1: Specifications for individual materials; Magnetically hard materials (IEC 60404-8-1:2001) |
| DIN IEC 60413-1980 |
確定電機電刷材料物理性能的試驗規程 |
Test procedures for determining physical properties of brush materials for electrical machines |
| DIN IEC 60450-1991 |
新的和老化的電工絕緣紙平均粘滯聚合度的測量 |
Measurement of the average viscometric degree of polymerization of new and aged electrical papers; identical with IEC 60450:1974 |
| DIN IEC 60455-3-2-2000 |
電氣絕緣用無溶劑可聚合樹脂化合物規范.第3部分:單項材料規范.第2活頁:石英充填環氧樹脂復合物 |
Specification for solventless polymerisable resinous compounds used for electrical insulation - Part 3: Specifications for individual materials; Sheet 2: Quartz filled epoxy resinous compounds (IEC 60455-3-2:1987 + A1:1994); German version HD 307.3.2 S2:1 |
| DIN IEC 60467-1978 |
電機用碳刷的物理性能的測定的檢驗方法 |
Test Procedures for Determining Physical Properties of Carbon Brushes for Electrical Machines |
| DIN IEC 60468-1981 |
金屬材料電阻率測量方法 |
Method of measurement of resistivity of metallic materials |
| DIN IEC 60469-1-1991 |
脈沖技術和儀器.第1部分:脈沖術語和定義 |
Pulse techniques and apparatus; part 1: pulse terms and definitions; identical with IEC 60469-1:1987 |
| DIN IEC 60469-2-1991 |
脈沖技術和儀器.第2部分:脈沖測量和分析.概論 |
Pulse techniques and apparatus; pulse measurement and analysis; general considerations; identical with IEC 60469-2:1987 |
| DIN IEC 60476-1995 |
核儀表.使用電離輻射源的電氣測量系統和儀表.一般狀況 |
Nuclear instrumentation - Electrical measuring systems and instruments utilizing ionizing radiation sources - General aspects (IEC 60476:1993) |
| DIN IEC 60483-1988 |
高機電耦合壓電陶瓷的動態測量導則 |
Guide to dynamic measurements of piezoelectric ceramics with high electromechanical coupling; identical with IEC 60483, edition 1976 |
| DIN IEC 60487-1-1990 |
地面無線電中繼系統用設備的測量方法.第1部分:分系統和模擬無線電中繼系統通用測量方法 |
Methods of measurement for equipment used in terrestrial radio-relay systems; measurements common to sub-systems and simulated radio-relay systems; identical with IEC 60487-1:1984 |
| DIN IEC 60487-2-1-1987 |
地面無線電接力系統所用設備的測量方法.分系統測量.總則 |
Methods of measurement for equipment used in terrestrial radio-relay system; measurements for sub-systems; general; identique with IEC 487-2-1, edition 1981 |
| DIN IEC 60487-2-2-1987 |
地面無線電接力系統所用設備的測量方法.分系統測量.備用波道倒換機 |
Methods of measurement for equipment used in terrestrial radio-relay systems; measurements for sub-systems; stand-by channel switching equipment; identical with IEC 60487-2-2, edition 1981 |
| DIN IEC 60487-2-3-1988 |
地面無線電接力系統所用設備的測量方法.第2部分:分系統測量.第3節:射頻分支網絡 |
Methods of measurement for equipment used in terristrial radio-relay systems; measurement for sub-systems; R.F. branching network; identical with IEC 60487-2-3:1984 |
| DIN IEC 60487-2-4-1988 |
地面無線電接力系統所用設備的測量方法.第2部分:分系統測量.第4節:調頻器 |
Methods of measurement for equipment used in terrestrial radio-relay systems; measurements for sub-systems; frequency modulators; identical with IEC 60487-2-4, edition 1984 |
| DIN IEC 60487-2-5-1989 |
地面無線電接力系統所用設備的測量方法.第2部分:分系統測量.第5節:頻率解調器 |
Methods of measurement for equipment used in terrestrial radio-relay systems; measurements for sub-systems; frequency demodulators; identical with IEC 60487-2-5:1984 |
| DIN IEC 60487-2-6-1992 |
地面無線電接力系統所用設備的測量方法.第2部分:分系統測量.第6節:分集.雙路和熱備用設備 |
Methods of measurement for equipment used in terrestrial radio-relay systems; measurements for sub-systems; diversity, twin-path and hot stand-by equipment; identical with IEC 60487-2-6:1984 |
| DIN IEC 60487-2-7-1989 |
地面無線電接力系統所用設備的測量方法.第2部分:分系統測量.第7節:無線電發射機 |
Methods of measurement for equipment used in terrestrial radio-relay systems; measurements for sub-systems; radio transmitters; identical with IEC 60487-2-7:1986 |
| DIN IEC 60487-2-8-1989 |
地面無線電接力系統所用設備的測量方法.第2部分:分系統測量.第8節:無線電接收機 |
Methods of measurement for equipment used in terrestrial radio-relay systems; measurements for sub-systems; radioreceivers; identical with IEC 60487-2-8:1986 |
| DIN IEC 60487-3-1994 |
地面無線電中繼系統使用設備的測量方法.第3部分:模似系統 |
Methods of measurement for equipment used in terrestrial radio-relay systems; part 3: simulated systems (IEC 60487-3:1975); German version HD 477.3 S1:1988 |
| DIN IEC 60487-3-2-1987 |
地面無線電接力系統所用設備的測量方法.第3部分:模擬系統.第2節:基帶測量 |
Methods of measurement for equipment used in terrestrial radio-relay systems; simulated systems; measurement in the baseband; identical with IEC 60487-3-2:1981 |
| DIN IEC 60487-3-3-1988 |
地面無線電接力系統所用設備的測量方法.第3部分:模擬系統.第3節:黑白和彩色電視傳輸?shù)臏y(cè)量 |
Methods of measurement for equipment used in terrestrial radio-relay systems; simulated systems; measurements for monochrom and colour television transmission; identical with IEC 60487-3-3, edition 1981 |
| DIN IEC 60487-3-4-1987 |
地面無線電接力系統所用設備的測量方法.第3部分:模擬系統.第4節:分頻多路傳輸?shù)臏y(cè)量 |
Methods of measurement for equipment used in terrestrial radio-relay systems; simulated systems; measurement for f.d.m. transmission; identical with IEC 60487-3-4, edition 1982 |
| DIN IEC 60487-3-5-1988 |
地面無線電中繼系統所用設備的測量方法.第3部分:模擬系統.第5節:互干擾測量 |
Methods of measurement for equipment used in terrestrial radio-relay systems; simulated systems; measurement of mutual interference; identical with IEC 60487-3-5, edition 1982 |
| DIN IEC 60487-3-6-1991 |
地面無線電中繼系統所用設備的測量方法.第3部分:模擬系統.第6節:聲節目傳輸測量 |
Methods of measurement for equipment used in terrestrial radio-relay systems; simulated systems; measurement for sound-programme transmission; identical with IEC 60487-3-6:1984 |
| DIN IEC 60489-1-1981 |
移動設備中用無線電設備的測量方法.第1部分:一般定義和標準測量條件 |
Methods of measurement for radio equipment used in the mobile services; part 1: general definitions and standard conditions of measurement |
| DIN IEC 60489-2-1986 |
移動設備中用無線電設備的測量方法.第2部分:采用A3E.F3E或G3E發射的發射機 |
Methods of measurement for radio equipment used in the mobile service; transmitters employing A3E (A3) or F3E (F3) emissions; identical with IEC 60489-2, edition 1978 (status as of 1983) |
| DIN IEC 60489-3-1986 |
移動設備中用無線電設備的測量方法.第3部分:A3E或F3E發射的接收機 |
Methods of measurement for radio equipment used in the mobile service; receivers for A3E(A3) or F3E(F3) emissions; identical with IEC 60489-3, edition 1979 (status as of 1983) |
| DIN IEC 60489-4-1986 |
移動移動設備中用無線電設備的測量方法.第4部分:采用單邊帶發射的(R3E.H3E或J3E)發射機 |
Methods of measurement for radio equipment used in the mobile services; transmitters employing single-sideband emissions (A3A, A3H or A3J); identical with IEC 60489-4, edition 1980 (status as of 1983) |
| DIN IEC 60489-5-1989 |
移動設備中用無線電設備的測量方法.第5部分:采用單邊帶技術(R3E.H3E或J3E)的接收機 |
Methods of measurement for radio equipment used in the mobile services; receivers employing single-sideband techniques (R3E, H3E or J3E); identical with IEC 60489-5:1987 |
| DIN IEC 60489-6-1990 |
移動設備中用無線電設備的測量方法.第6部分:選擇呼叫和數據設備 |
Methods of measurement for radio equipment used in the mobile services; selective calling and data equipment; identical with IEC 60489-6:1987 |
| DIN IEC 60489-8-1987 |
移動設備中用無線電設備的測量方法.第8部分:天線 |
Methods of measurement for radio equipment used in the mobile services; methods of measurement for antennas; identical with IEC 60489-8, edition 1984 |
| DIN IEC 60509-1997 |
氣密封可再充電的單一鎳鎘按鈕電池 |
Accumulators - Sealed nickel-cadmium button rechargeable single cells (IEC 60509:1988); German version HD 561 S1:1991 |
| DIN IEC 60510-1-1987 |
衛星地面站用無線電設備的測量方法.第1部分:分系統和分系統組合件通用的測量.第2節:射頻范圍內的測量 |
Methods of measurement for radio equipment used in satellite earth stations; general; identical with IEC 60510-1, edition 1975 (status as of 1980) |
| DIN IEC 60510-1-2-1988 |
衛星地面站用無線電設備的測量方法.第1部分:分系統和分系統組合件通用的測量.第2節:射頻范圍內的測量 |
Methods of measurement for radio equipment used in satellite earth stations; measurement common to sub-systems and combinations of sub-systems; measurement in the r.f. range; identical with IEC 60510-1-2:1984 |
| DIN IEC 60510-1-3-1993 |
衛星地面站用無線電設備的測量方法.分系統和分系統組合件的測量.中頻范圍的測量 |
Methods of measurement for radio equipment used in satellite earth stations; measurement common to sub-systems and combinations of sub-systems; measurement in the i.f.range; identical with IEC 60510-1-3:1980 + A1:1991 |
| DIN IEC 60510-1-4-1989 |
衛星地面站用無線電設備的測量方法.第1部分:分系統和分系統組合件通用的測量.第4節:基本頻帶域中的測量 |
Methods of measurement for radio equipment used in satellite earth stations; measurement common to sub-systems and combinations of sub-systems; measurement in the baseband; identical with IEC 60510-1-4:1986 |
| DIN IEC 60510-1-5-1991 |
衛星地面站用無線電設備的測量方法.第1部分:分系統和分系統組合件通用的測量.第5節:噪聲溫度測量 |
Methods of measurement for radio equipment used in satellite earth stations; measurement common to sub-systems and combinations of sub-systems; noise temperature measurements; identical with IEC 60510-1-5:1988 |
| DIN IEC 60510-2-1-1993 |
衛星地面站用無線電設備的測量方法.分系統的測量.總則、天線(包括饋線網絡) |
Methods of measurement for radio equipment used in satellite earth stations; measurement for sub-systems; general, antenna (including feed network); identical with IEC 60510-2-1:1978 |
| DIN IEC 60510-2-3-1993 |
衛星地面站用無線電設備的測量方法.分系統測量.低噪聲放大器 |
Methods of measurement for radio equipment used in satellite earth-stations; measurement for sub-systems; low-noise amplifier; identical with IEC 60510-2-3:1989 |
| DIN IEC 60510-2-4-1993 |
衛星地面站用無線電設備的測量方法.分系統的測量.發射和接收轉換器 |
Methods of measurement for radio equipment used in satellite earth stations; measurements for sub-systems; up and down converters; identical with IEC 60510-2-4:1988 |
| DIN IEC 60510-2-7-1993 |
衛星地面站無線電設備的測量方法.子系統的測量.大功率放大器 |
Methods of measurement for radio equipment used in satellite earth stations; measurements for sub-systems; high-power amplifier; identical with IEC 60510-2-7:1989 |
| DIN IEC 60510-3-1-1987 |
衛星地面站用無線電設備的測量方法.第3部分:分系統組合件的測量方法.第1節:總則 |
Methods of measurement for radio equipment used in satellite earth stations; methods of measurement for combinations of sub-systems; general; identical with IEC 60510-3-1, edition 1981 |
| DIN IEC 60510-3-2-1987 |
衛星地面站用無線電設備的測量方法.第3部分:分系統結合的測量方法.第2節:接受范圍為4GHz-6GHz的系統品質因數(G/T)的測量 |
Methods of measurement for radio equipment used in satellite earth stations; methods of measurement for combinations of sub-systems; measurement of the figure of merit (G/T) of the receiving system in the 4 GHz to 6 GHz range; identical with IEC 60510-3-2 |
| DIN IEC 60510-3-3-1992 |
衛星地面站用無線電設備的測量方法.第3部分:分系統組合件的測量方法.第3節:黑白電視和彩色電視傳送的測量 |
Methods of measurement for radio equipment used in satellite earth stations; methods of measurement for combinations of sub-systems; measurement for monochrome and colour television transmission; identical with IEC 60510-3-3:1988 |
| DIN IEC 60512-2/A1-1995 |
電子設備用機電件.基本試驗規程和測量方法.第2部分:一般檢查,電連續性和接觸電阻試驗,絕緣試驗和電壓應力試驗 |
Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 2: General examination, electrical continuity and contact resistance tests, insulation tests and voltage stress tests (IEC 60512-2:1985/A1:1994) |
| DIN IEC 60512-5-1994 |
電子設備用機電件.基本試驗規程和測量方法.第5部分:沖擊試驗(不固定件).靜載試驗(固定件).壽命試驗和過載試驗 |
Electromechanical components for electronic equipment; basic testing procedures and measuring methods; part 5: impact tests (free components), static load tests (fixed components), endurance tests and overload tests; identical with IEC 60512-5:1992 |
| DIN IEC 60512-7-1994 |
電子設備用機電件.基本試驗程序和測量方法.第7部分:機械操作試驗和密封試驗 |
Electromechanical components for electronic equipment; basic testing procedures and measuring methods; part 7: mechanical operating tests and sealing tests; identical with IEC 512-7-1978 |
| DIN IEC 60512-8-1994 |
電子設備用機電部件.基本試驗規程和試驗方法.第8部分:連接試驗(機械)和接觸件與接線端的機械試驗 |
Electromechanical components for electronic equipment; basic testing procedures and measuring methods; part 8: connector tests (mechanical) and mechanical tests on contacts and terminations; identical with IEC 512-8-1984 |
| DIN IEC 60512-9-1994 |
電子設備用機電件.基本試驗規程和測量方法.第9部分:雜項試驗 |
Electromechanical components for electronic equipment; basic testing procedures and measuring methods; part 9: miscellaneous tests; identical with IEC 60512-9:1992 |
| DIN IEC 60516 Bb.1-1988 |
CAMAC系統.數據處理用模塊式儀器系統.已出版的文件的目錄 |
CAMAC-system; a modular instrumentation system for data handling; list of published documents |
| DIN IEC 60516-1987 |
CAMAC系統.數據處理用模塊式儀器系統 |
CAMAC-system; a modular instrumentation system for data handling; identical with IEC 60516, edition 1975 (status as of 1984) |
| DIN IEC 60534-2-4-1990 |
工業過程控制閥.第2部分:流通能力.第4節:內在的流動特性線和調節比例關系 |
Industrial-process control valves; flow capacity; inherent flow characteristics and rangeability; identical with IEC 60534-2-4:1989 |
| DIN IEC 60534-5-1984 |
工業過程控制閥.第5部分:標記 |
Industrial-process control valves; part 5: marking |
| DIN IEC 60534-7-1992 |
工業過程控制閥.第7部分:.數據表 |
Industrial process control valves; control valve data sheet; identical with IEC 60534-7:1989 |
| DIN IEC 60544-2-1996 |
確定電離輻射對絕緣材料影響的導則.第2部分:輻照和試驗規程 |
Guide for determining the effects of ionizing radiation on insulating materials - Part 2: Procedures for irradiation and test (IEC 60544-2:1991) |
| DIN IEC 60547-1983 |
符合NIM標準(用于核電子儀器)的插件單和標準19英寸機架安裝單 |
Modular plug-in unit and standard 19-inch rack mounting unit based on NIM standard (for electronic nuclear instruments) |
| DIN IEC 60552-1987 |
CAMAC-多機箱系統組織.分支信息通道和AI型CAMAC機箱控制器規范 |
CAMAC - Organization of multi-crate systems; specification of the Branch-highway and CAMAC crate controller type A1; identical with IEC 60552, edition 1977 (status as of 1984) |
| DIN IEC 60559-1992 |
微處理機系統的二進制浮點運算 |
Binary floating-point arithmetic for microprocessor systems (IEC 60559:1989); german version HD 592 S1:1991 |
| DIN IEC 60562-1980 |
電子管入射電離輻射的測量 |
Measurements of incidental ionizing radiation from electronic tubes |
| DIN IEC 60568-1983 |
動力反應堆內中子注量率(通量)測量?jī)?nèi)芯體儀器 |
In-core instrumentation for neutron fluence rate (flux) measurements in power reactors |
| DIN IEC 60574-17-1991 |
視聽.視頻和電視設備與系統.第17部分:音頻學習系統 |
Audiovisual, video and television equipment and systems; audio-learning systems; identical with IEC 60574-17:1989 |
| DIN IEC 60574-18-1991 |
視聽.視頻和電視設備及系統.第18部分:聲像應用的自動幻燈片放映機與內裝雙向三極管開關的連接器 |
Audiovisual, video and television equipment and systems; connectors for automatic slide projectors with built-in triacs for audiovisual applications; identical with IEC 60574-18:1987; german version HD 369.18 S1:1989 |
| DIN IEC 60576-1985 |
便攜式鉆孔測井設備(深至300m).一般特性 |
Portable bore-hole logging equipment (down to 300 m); general characteristics |
| DIN IEC 60584-2-1992 |
熱電偶.溫差電壓的極限偏差 |
Thermocouples; tolerances; identical with IEC 60584-2:1982 (status of 1989); german version HD 446.2 S2:1990 |
| DIN IEC 60587-1996 |
電氣絕緣材料在嚴酷環境條件下使用時耐起痕和耐腐蝕評定的試驗方法 |
Test methods for evaluating resistance to tracking and erosion of electrical insulating materials used under severe ambient conditions (IEC 60587:1984); German version HD 380 S2:1986 |
| DIN IEC 60590-1986 |
新礦物絕緣油中芳香烴含量的測定 |
(Determination of the aromatic hydrocarbon content of new mineral insulating oils; identical with IEC 60590, edition 1977) |
| DIN IEC 60601-2-11/A1-1993 |
醫用電氣設備.γ射線治療設備.電氣和機械安全性的特殊規定 |
(Medical electrical equipment; gamma beam radiotherapy equipment; particular requirements for electrical and mechanical safety; identical with IEC 60601-2-11 AMD 1:1988) |
| DIN IEC 60602-1989 |
B型螺旋掃描錄象機 |
(Type B helical video recorders; identical with IEC 60602:1980 (status of 1987)) |
| DIN IEC 60603-11-1995 |
印制板用頻率低于3MHz的連接器.第11部分:同軸連接器的詳細規范(自由連接器和固定連接器的尺寸) |
(Connectors for frequencies below 3 MHz for use with printed boards - Part 11: Detail specification for concentric connectors (dimensions for free connectors and fixed connectors) (IEC 60603-11:1992)) |
| DIN IEC 60605-1-1986 |
電氣工程;設備可靠性試驗.第1部分:一般要求 |
(Electrical engineering; equipment reliability testing; general requirements; identical with IEC 60605-1, edition 1978) |
| DIN IEC 60605-3-1-1988 |
電氣工程;設備可靠性試驗.第3部分:優選的試驗條件.第1節:低模擬度戶內便攜設備 |
(Electrical engineering; equipment reliability testing; preferred test conditions; indoor portable equipment; low degree of simulation; identical with IEC 60605-3-1:1986) |
| DIN IEC 60605-3-4-1993 |
電氣工程;設備可靠性試驗.優選試驗條件.非固定驅動設備.低模擬程度 |
(Equipment reliability testing; preferred test conditions; equipment for portable and non-stationary use; low degree of simulation; identical with IEC 60605-3-4:1992) |
| DIN IEC 60605-4-1988 |
電氣工程;設備可靠性試驗.第4部分:設備可靠性的估計值和置信極限 |
(Electrical engineering; equipment reliability testing; part 4: procedures for determining point estimates and confidence limits from equipment reliability determinations tests; identical with IEC 60605-4, edition 1986) |
| DIN IEC 60605-6-1999 |
設備可靠性的試驗.第6部分:確定假設的恒定故障率或恒定故障密度的統計測試 |
(Equipment reliability testing - Part 6: Tests for the validity of the constant failure rate or constant failure intensity assumptions (IEC 60605-6:1997)) |
| DIN IEC 60625-1-1981 |
可編程序測量?jī)x的接口系統(字節串行.位并行).第1部分:功能規范.電氣規范.機械規范.系統應用和對設計者及用 |
(An interface system for programmable measuring instruments (byte serial, bit parallel); part 1: functional specifications, electrical specifications, mechanical specifications, system applications and requirements for designer and user) |
| DIN IEC 60625-2-1981 |
可編程序測量?jī)x的接口系統(字節串行.位并行).第2部分:代碼和格式慣例 |
(An interface system for programmable measuring instruments (byte serial, bit parallel); part 2: code and format conventions) |
| DIN IEC 60628-1995 |
絕緣液體在電應力和電離作用下的析氣 |
(Gassing of insulating liquids under electrical stress and ionization (IEC 60628:1985); German version HD 488 S1:1987) |
| DIN IEC 60631-1980 |
電動和電磁制動系統的特性和試驗 |
(Characteristics and tests of electrodynamic and electromagnetic braking systems) |
| DIN IEC 60640-1987 |
CAMAC-串行信息通道接口系統 |
CAMAC-serial highway interface system; identical with IEC 60640, eidtion 1979 (as of 1984) |
| DIN IEC 60642-1988 |
頻率控制和選擇用壓電陶瓷諧振子和諧振器.第I章:標準值和條件.第Ⅱ章:測量和試驗條件 |
Piezoelectric ceramic resonators and resonator units for frequency control and selection; standard values and conditions; measuring and test conditions; identical with IEC 60642, edition 1979 |
| DIN IEC 60642-3-1993 |
壓電陶瓷諧振器.第3部分:標準外形 |
Piezoelectric ceramic resonators; part 3: standard outlines; identical with IEC 60642-3:1992 |
| DIN IEC 60647-1990 |
電源用磁性氧化物磁芯(EC磁芯)的尺寸 |
Magnetic oxide cores; EC-cores intended for use in power supplies; dimensions; identical with IEC 60647:1979 |
| DIN IEC 60654-1-1984 |
工業過程測量和控制設備的工作條件.第1部分:溫度.濕度和大氣壓 |
Operating conditions for industrial-process measurement and control equipment; part 1: temperature, humidity and barometric pressure |
| DIN IEC 60677-1986 |
CAMAC系統中的字組轉移 |
Block transfers in CAMAC systems; identical with IEC 60677, edition 1980 |
| DIN IEC 60678-1985 |
IEC標準中使用的CAMAC術語的定義 |
Definitions of CAMAC terms used in IEC-publications; identical with IEC 60678, edition 1980 |
| DIN IEC 60679-2-1997 |
石英晶體受控振蕩器.第2部分:石英晶體受控振蕩器使用導則 |
Quartz crystal controlled oscillators - Part 2: Guide to the use of quartz crystal controlled oscillators (IEC 60679-2:1981) |
| DIN IEC 60684-3-116 bis 118-1996 |
絕緣軟管規范.第3部分:各種型號軟管的規范.第116至118活頁:通用擠壓氯丁絕緣軟管 |
Specification for flexible insulating sleeving - Part 3: Specification requirements for individual types of sleeving; Sheets 116 to 118: Extruded polychloroprene, general purpose (IEC 60684-3-116 to 118:1991); German version HD 523.3.116 to 118 S1:1993 |
| DIN IEC 60684-3-201-1996 |
絕緣軟管規范.第3部分:各種型號軟管的規范.第201活頁:交聯聚氯乙烯制標準型號收縮率為2:1的柔性熱收縮軟管 |
Specification for flexible insulation sleeving - Part 3: Specification requirements for individual types of sleeving; Sheet 201: Heat shrinkable sleeving, general purpose, flexible, cross-linked PVC, shrink ratio 2:1 (IEC 60684-3-201:1991); German version |
| DIN IEC 60684-3-209-1996 |
絕緣軟管規范.第3部分:各種型號軟管的規范.第209活頁:收縮率為2:1耐火的標準型號聚烯烴熱收縮軟管 |
Specification for flexible insulating sleeving - Part 3: Specification requirements for individual types of sleeving; Sheet 209: Heat shrinkable sleeving, general purpose, flame retarded polyolefin shrink ratio 2:1 (IEC 60684-3-209:1987); German version H |
| DIN IEC 60684-3-406 bis 408-1996 |
絕緣軟套管規范.第3部分:各種型號套管的規范要求,第406至408活頁:有PVC為基底涂覆層的玻璃絲織套管 |
Specification for flexible insulating sleeving - Part 3: Specification requirements for individual types of sleeving; Sheets 406 to 408: Glass textile sleeving with PVC based coating (IEC 60684-3-406 to 408:1988); German version HD 523.3.406 to 408 S1:199 |
| DIN IEC 60692-2001 |
核設備.電離輻射密度測量裝置.定義和檢驗方法 |
Nuclear instrumentation - Density gauges utilizing ionizing radiation - Definitions and test methods (IEC 60692:1999) |
| DIN IEC 60698-1989 |
電視磁帶機的測量方法 |
Measuring methods for television tape machines; identical with IEC 60698:1981 |
| DIN IEC 60706-1-1986 |
電氣工程.設備維修導則.第1部分:第1節.第2節.第3節:引言.要求.維修大綱 |
Electrical engineering; guide on maintainability of equipment; part 1: sections-one, two and three; introduction, requirements and maintainability programme; identical with IEC 60706-1, edition 1982 |
| DIN IEC 60706-2-2001 |
設備維修導則.第2部分:第5節:在設計階段的維修研究 |
Guide on maintainability of equipment - Part 2: Section 5: Maintainability studies during the design phase (IEC 60706-2:1990) |
| DIN IEC 60706-3-1990 |
電氣工程.設備維修導則.第3部分:第6節.第7節:數據的驗證和采集.分析和表述 |
Electrical engineering; guide on maintainability of equipment; part 3: sections six and seven; verification and collection, analysis and presentation of data; identical with IEC 60706-3:1987 |
| DIN IEC 60706-4-1999 |
設備維修導則.第4部分:第8節:維修及其支持維修的規則 |
Guide on maintainability of equipment - Part 4: Section 8: Maintenance and maintenance support planning (IEC 60706-4:1992) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com