標準號 |
中文名稱 |
英文名稱 |
| DIN EN 60352-5-2002 |
無焊連接.第5部分:壓入連接.一般要求、試驗方法和實施指南 |
(Solderless connections - Part 5: Press-in connections; General requirements, test methods and practical guidance (IEC 60352-5:2001); German version EN 60352-5:2001) |
| DIN EN 60352-5-2004 |
無焊連接.第5部分:壓入式連接.一般要求、試驗方法和實用指南 |
|
| DIN EN 60352-6-1998 |
無焊連接.第6部分:防滲漏連接.一般要求.檢驗方法和使用說明 |
(Solderless connections - Part 6: Insulation piercing connections; general requirements, test methods and practical guidance (IEC 60352-6:1997); German version EN 60352-6:1997) |
| DIN EN 60352-7-2003 |
無焊連接.第7部分:彈簧夾件連接.一般要求、試驗方法和使用指南 |
(Solderless connections - Part 7: Spring clamp connections; General requirements, test methods and practical guidance (IEC 60352-7:2002); German version EN 60352-7:2002) |
| DIN EN 60357-2001 |
鹵素白熾燈(車燈除外) |
(Tungsten halogen lamps (non-vehicle) (IEC 60357:1982 + A1:1984 up to A13:2000); German version EN 60357:1988 + A4:1991 up to A13:2000) |
| DIN EN 60359-2002 |
電氣和電子測量設備.性能表示 |
(Electrical and electronic measurement equipment - Expression of the performance (IEC 60359:2001); German version EN 60359:2002) |
| DIN EN 60360-1999 |
燈頭溫升測量的標準方法 |
(Standard method of measurement of lamp cap temperature rise (IEC 60360:1998); German version EN 60360:1998) |
| DIN EN 60368-1-2000 |
評定質量的壓電濾波器.第1部分:一般規范 |
(Piezoelectric filters of assessed quality - Part 1: Generic specification (IEC 60368-1:2000); German version EN 60368-1:2000) |
| DIN EN 60368-2-2-1999 |
壓電濾波器.第2部分:壓電濾波器應用指南.第2節:壓電陶瓷濾波器 |
(Piezoelectric filters - Part 2: Guide to the use of piezoelectric filters - Section 2: Piezoelectric ceramic filters (IEC 60368-2-2:1996); German version EN 60368-2-2:1999) |
| DIN EN 60368-3-2002 |
經質量評定的壓電濾波器.第3部分:標準外形和引線接觸 |
(Piezoelectric filters of assessed quality - Part 3: Standard outlines and lead connections (IEC 60368-3:2001); German version EN 60368-3:2001) |
| DIN EN 60368-4-1-2001 |
評定質量的壓電濾波器.第4-1部分:空白詳細規范.能力鑒定 |
(Piezoelectric filters of assessed quality - Part 4-1: Blank detail specification; Capability approval (IEC 60368-4-1:2000); German version EN 60368-4-1:2000 + Corrigendum:2001) |
| DIN EN 60368-4-2001 |
評定質量的壓電濾波器.第4部分:分規范.能力鑒定 |
(Piezoelectric filters of assessed quality - Part 4: Sectional specification; Capability approval (IEC 60368-4:2000); German version EN 60368-4:2000 + Corrigendum:2001) |
| DIN EN 60371-1-2004 |
云母基絕緣材料規范.第1部分:定義和一般要求 |
(Specification for insulating materials based on mica - Part 1: Definitions and general requirements (IEC 60371-1:2003); German version EN 60371-1:2003) |
| DIN EN 60371-1-2004 |
云母基絕緣材料規范.第1部分:定義和一般要求 |
|
| DIN EN 60371-2-1997 |
以云母為基材的絕緣材料規范.第2部分:試驗方法 |
(Specification for insulating materials based on mica - Part 2: Methods of test (IEC 60371-2:1987 + A1:1994); German version EN 60371-2:1997) |
| DIN EN 60371-3-1-1997 |
云母基絕緣材料規范.第3部分:單項材料規范.第1活頁:換向器隔板和材料 |
(Specification for insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 1: Commutator separators and materials (IEC 60371-3-1:1984); German version EN 60371-3-1:1995) |
| DIN EN 60371-3-2-1997 |
云母基絕緣材料規范.第3部分:單一材料規范.第2活頁:云母紙 |
(Specification for insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 2: Mica paper (IEC 60371-3-2:1991); German version EN 60371-3-2:1995) |
| DIN EN 60371-3-3-1997 |
云母基絕緣材料規范.第3部分:單項材料規范.第3活頁:加熱設備用硬質云母材料 |
(Specification for insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 3: Rigid mica materials for heating equipment (IEC 60371-3-3:1983); German version EN 60371-3-3:1995) |
| DIN EN 60371-3-4-1997 |
云母基絕緣材料規范.第3部分:單項材料規范.第4活頁:用B級環氧樹脂粘合劑粘結的聚酯薄膜襯底云母紙 |
(Specification for insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 4: Polyester film-backed mica paper with a B-stage epoxy resin binder (IEC 60371-3-4:1992); German version EN 60371-3-4:1995) |
| DIN EN 60371-3-5-1997 |
云母基絕緣材料規范.第3部分:單項材料規范.第5活頁:用環氧樹脂粘合劑粘結的待浸漬處理的玻璃纖維織物襯底云 |
(Specification for insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 5: Glass-backed mica paper with an epoxy resin binder for post-impregnation (VPI) (IEC 60371-3-5:1992); German version EN 60371-3-5:1995) |
| DIN EN 60371-3-6-1997 |
云母基絕緣材料規范.第3部分:單項材料規范.第6活頁:用B級環氧樹脂粘合劑粘結的玻璃纖維織物襯底云母紙 |
(Specification for insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 6: Glass-backed mica paper with a B-stage epoxy resin binder (IEC 60371-3-6:1992); German version EN 60371-3-6:1995) |
| DIN EN 60371-3-7-1997 |
云母基絕緣材料.第3部分:單項材料規范.第7活頁:單導體膠帶用帶有環氧樹脂的聚脂薄膜云母紙 |
(Insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 7: Polyester film mica paper with an epoxy resin binder for single conductor taping (IEC 60371-3-7:1995 + Corrigendum 1995); German version EN 60371-3-7:1995) |
| DIN EN 60371-3-8-1997 |
云母基絕緣材料規范.第3部分:單項材料規范.第8活頁:耐火安全電纜用云母紙帶 |
(Insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 8: Mica paper tapes for flame-resistant security cables (IEC 60371-3-8:1995 + Corrigendum 1995); German version EN 60371-3-8:1995) |
| DIN EN 60371-3-9-1997 |
云母基絕緣材料規范.第3部分:單項材料規范.第9活頁:模制膠合云母板 |
(Insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 9: Moulding micanite (IEC 60371-3-9:1995 + Corrigendum 1995); German version EN 60371-3-9:1995) |
| DIN EN 60372-2005 |
絕緣子串單球窩連接的鎖緊裝置.尺寸和試驗(IEC 60372-1984 + A1-1991 + A2-2003) |
|
| DIN EN 60375-2004 |
有關電路和磁路的規定 |
|
| DIN EN 60379-2004 |
家用電蓄水式熱水器的性能測量方法 |
|
| DIN EN 60382-1994 |
過程控制系統用模擬氣動信號 |
(Analogue pneumatic signal for process control systems (IEC 60382:1991); German version EN 60382:1993) |
| DIN EN 60383-1 Berichtigung 1-2001 |
DINEN60383-1-1997(VDE0446Teil1)的勘誤 |
(Corrigenda to DIN EN 60383-1 (VDE 0446 Teil 1):1997-05; German version EN 60383-1:1996/A11:1999) |
| DIN EN 60383-1-1997 |
公稱電壓高于1000V的架空線路用絕緣子.第1部分:交流系統用陶瓷或玻璃絕緣子的定義,試驗方法和驗收要求 |
(Insulators for overhead lines with a nominal voltage above 1 kV - Part 1: Ceramic or glass insulator units for a.c. systems; definitions, test methods and acceptance criteria (IEC 60383-1:1993); German version EN 60383-1:1996) |
| DIN EN 60383-2-1995 |
公稱電壓高于1000V的架空線路用絕緣子.第2部分:交流電路系統絕緣子串和絕緣子裝置.試驗方法和驗收指標 |
(Insulators for overhead lines with a nominal voltage above 1000 V - Part 2: Insulator strings and insulator sets for a.c. systems; definitions, test methods and acceptance criteria (IEC 60383-2:1993); German version EN 60383-2:1995) |
| DIN EN 60384-1-2002 |
電子設備用固定電容器.第1部分:總規范. |
(Fixed capacitors for use in electronic equipment - Part 1: Generic specification (IEC 60384-1:1999, modified); German version EN 60384-1:2001) |
| DIN EN 60384-14-2-2005 |
電子設備用固定電容器.第14-2部分:空白詳細規范:抑制電磁干擾和電源網絡連接用固定電容器.安全試驗 |
|
| DIN EN 60384-14-2-2005 |
電子設備用固定電容器.第14-2部分:空白詳細規范:抑制電磁干擾和電源網絡連接用固定電容器.安全試驗 |
|
| DIN EN 60384-14-3-2005 |
電子設備用固定電容器.第14-3部分:空白詳細規范:抑制電磁干擾和電源網絡連接用固定電容器.評定等級DZ |
|
| DIN EN 60384-14-3-2005 |
電子設備用固定電容器.第14-3部分:空白詳細規范:抑制電磁干擾和電源網絡連接用固定電容器.評定等級DZ |
|
| DIN EN 60384-20-1-1999 |
電子設備用固定電容器.第20部分:空白詳細規范:金屬化聚苯硫薄膜介質表面安裝直流固定電容器.EZ級評定 |
(Fixed capacitors for use in electronic equipment - Part 20: Blank detail specification: Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors; assessment level EZ (IEC 60384-20-1:1996); German version EN 60384-20-1:1999) |
| DIN EN 60384-20-1999 |
電子設備用固定電容器.第20部分:分規范:金屬化聚苯硫薄膜介質直流表面安裝固定電容器 |
(Fixed capacitors for use in electronic equipment - Part 20: Sectional specification: Fixed metallized polyphenylene sulfide film dielectric surface mount DC capacitors (IEC 60384-20:1996); German version EN 60384-20:1999) |
| DIN EN 60384-21-1-2005 |
電子設備用固定電容器.第21-1部分:空白詳細規范:1級陶瓷介質的表面安裝固定多層電容器.評定級別EZ |
|
| DIN EN 60384-21-2005 |
電子設備用固定電容器.第21部分:分規范:1級陶瓷介質的表面安裝固定多層電容器 |
|
| DIN EN 60384-22-1-2005 |
電子設備用固定電容器.第22-1部分:空白詳細規范:2級陶瓷介質的表面安裝固定多層電容器.評定級別EZ |
|
| DIN EN 60384-22-2005 |
電子設備用固定電容器.第22部分:分規范:2級陶瓷介質的表面安裝固定多層電容器 |
|
| DIN EN 60387-1993 |
交流電表的符號 |
(Symbols for alternating-current electricity meters (IEC 60387:1992); German version EN 60387:1992) |
| DIN EN 60398-2000 |
工業電熱裝置.通用試驗方法 |
(Industrial electroheating installations - General test methods (IEC 60398:1999); German version EN 60398:1999) |
| DIN EN 60399-1999 |
帶燈罩座環的E14和E27燈座柱筒螺紋用標準活頁 |
(Standard sheets for barrel thread for E14 and E27 lampholders with shade holder ring (IEC 60399:1972 + A1:1997 + A2:1999); German version EN 60399:1993 + A1:1997 + A2:1999) |
| DIN EN 604-1-1997 |
鋁和鋁合金.鑄鍛毛坯.第1部分:交貨技術條件 |
(Aluminium and aluminium alloys - Cast forging stock - Part 1: Technical conditions for inspection and delivery; German version EN 604-1:1997) |
| DIN EN 604-2-1997 |
鋁和鋁合金.鑄鍛毛坯.第2部分:極限尺寸和形狀公差 |
(Aluminium and aluminium alloys - Cast forging stock - Part 2: Tolerances on dimensions and form; German version EN 604-2:1997) |
| DIN EN 60400 Berichtigung 1-2003 |
DINEN60400-2003的技術勘誤1 |
(Corrigendum to DIN EN 60400 (VDE 0616 Part 3):2003-03 (CENELEC-Corrigendum to EN 60400:2000/A1:2002)) |
| DIN EN 60400-2003 |
管形熒光燈和啟動器燈座 |
(Lampholders for tubular fluorescent lamps and starterholders (IEC 60400:1999, modified + A1:2002); German version EN 60400:2000 + A1:2002) |
| DIN EN 60401-3-2004 |
軟磁材料制芯的術語和命名.第3部分:寫入變壓器和電感器磁芯制造廠產品目錄中的數據格式指南 |
|
| DIN EN 60404-14-2003 |
磁性材料.第14部分:用拔出或旋轉法對鐵磁材料試樣的磁偶極矩的測量方法 |
(Magnetic materials - Part 14: Methods of measurement of the magnetic dipole moment of a ferromagnetic material specimen by the withdrawal or rotation method (IEC 60404-14:2002); German version EN 60404-14:2002) |
| DIN EN 60404-2-1998 |
磁性材料.第2部分:用愛普斯坦方圈測定電工鋼片和鋼帶的磁性能的方法 |
(Magnetic materials - Part 2: Methods of measurement of the magnetic properties of electrical steel sheet and strip by means of an Epstein frame (IEC 60404-2:1996); German version EN 60404-2:1998) |
| DIN EN 60404-4-2002 |
磁性材料.第4部分:鐵和鋼直流磁特性測量方法 |
(Magnetic materials - Part 4: Methods of measurement of d.c. magnetic properties of magnetically soft materials (IEC 60404-4:1995 + A1:2000); German version EN 60404-4:1997 + A1:2002) |
| DIN EN 60404-6-2004 |
磁性材料.第6部分:使用環形樣品的頻率范圍在20 Hz 到 200 kHz的磁性軟金屬和粉末材料的磁性能測量方法 |
|
| DIN EN 60417-1-2000 |
用于設備的圖形符號.第1部分:總覽和應用 |
(Graphical symbols for use on equipment - Part 1: Overview and application (IEC 60417-1:1998); Trinlingual version EN 60417-1:1998) |
| DIN EN 60417-2-2000 |
用于設備的圖形符號.第2部分:符號原文 |
(Graphical symbols for use on equipment - Part 2: Symbol originals (IEC 60417-2:1998); Trilingual version EN 60417-2:1999) |
| DIN EN 60420-1994 |
高壓交流開關熔斷器 |
(High-voltage alternating current switch-fuse combinations (IEC 60420:1990); German version EN 60420:1993) |
| DIN EN 60423-1995 |
電氣設備用導管.電氣安裝用導管的外徑和導管及配件的螺紋 |
(Conduits for electrical purposes - Outside diameters of conduits for electrical installations and threads for conduits and fittings (IEC 60423:1993, modified); German version EN 60423:1994) |
| DIN EN 60424-1-2000 |
鐵氧體磁芯.表面不規則性指南 |
(Ferrite cores - Guide on the limits of surface irregularities - Part 1: General specification (IEC 60424-1:1999); German version EN 60424-1:1999) |
| DIN EN 60424-2-1998 |
鐵氧體磁芯表面不平度極限值的導則.第2部分:RM-磁芯 |
(Guidance on the limits of surface irregularities of ferrite cores - Part 2: RM-cores (IEC 60424-2:1997); German version EN 60424-2:1997) |
| DIN EN 60424-3-2000 |
鐵氧體磁芯.表面不規則性指南.第3部分:ETD磁芯和E磁芯 |
(Ferrite cores - Guide on the limits of surface irregularities - Part 3: ETD-cores and E-cores (IEC 60424-3:1999); German version EN 60424-3:1999) |
| DIN EN 60424-4-2001 |
鐵氧體磁芯.表面不規則性指南.第4部分:環芯 |
(Ferrit cores - Guide on the limits of surface irregularities - Part 4: Ring-cores (IEC 60424-4:2001); German version EN 60424-4:2001) |
| DIN EN 60427-2001 |
高壓交流電斷路器綜合試驗 |
(Synthetic testing of high-voltage alternating current circuit-breakers (IEC 60427:2000); German version EN 60427:2000) |
| DIN EN 60431-1998 |
磁性氧化物正方形磁芯(RM磁芯).尺寸和附件 |
(Dimensions of square cores (RM-cores) made of magnetic oxides and associated parts (IEC 60431:1983 + A1:1995); German version EN 60431:1997) |
| DIN EN 60431/A2-1999 |
磁氧化物制方芯(RM-芯)及其附件的尺寸.修正A2 |
(Dimensions of square cores (RM-cores) made of magnetic oxides and associated parts; Amendment A2; (IEC 60431:1983/A2:1996); German version EN 60431:1997/A2:1998) |
| DIN EN 60432-1-2000 |
白熾燈的安全規范.第1部分:家用和類似一般照明用鎢絲白熾燈 |
(Incandescent lamps - Safety specifications - Part 1: Tungsten filament lamps for domestic and similar general lighting purposes (IEC 60432-1:1999, modified); German version EN 60432-1:2000) |
| DIN EN 60432-1-2005 |
白熾燈.安全規范.第1部分:家用和類似場合普通照明用鎢絲燈 |
|
| DIN EN 60432-2-2000 |
白熾燈的安全規范.第2部分:家用和類似一般照明用的鹵鎢燈 |
(Incandescent lamps - Safety specifications - Part 2: Tungsten halogen lamps for domestic and similar general lighting purposes (IEC 60432-2:1999, modified); German version EN 60432-2:2000) |
| DIN EN 60432-3-2003 |
白熾燈.安全規范.第3部分:鹵鎢燈(非車用) |
(Incandescent lamps - Safety specifications - Part 3: Tungsten-halogen lamps (non-vehicle) (IEC 60432-3:2002); German version EN 60432-3:2003) |
| DIN EN 60432-3-2005 |
白熾燈.安全規范.第3部分:鎢鹵燈(非車用) |
|
| DIN EN 60433-1999 |
1kV以上額定電壓的架空電線用絕緣子.交流電系統用瓷絕緣子.長棒型絕緣子串的特性值 |
(Insulators for overhead lines with a nominal voltage above 1 kV - Ceramic insulators for a.c. systems - Characteristics of insulator units of the long rod type (IEC 60433:1998); German version EN 60433:1998) |
| DIN EN 60437-1998 |
高電壓絕緣子無線電干擾試驗 |
(Radio interference test on high-voltage insulators (IEC 60437:1997); German version EN 60437:1997) |
| DIN EN 60439-1 Bb.2-1997 |
封閉式低壓開關設備和控制設備成套裝置.第1部分:型式試驗和部分型式試驗組合.技術報告:故障電弧條件下檢驗 |
(Enclosed low-voltage switchgear and controlgear assemblies - Part 1: Typetested and partially typetested assemblies; technical report: Guide for testing under conditions of arcing due to an internal fault (IEC 61641:1996)) |
| DIN EN 60439-1-2000 |
低壓開關設備和控制設備組件.第1部分:型式試驗和部分型式試驗的組件 |
(Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies (IEC 60439-1:1999); German version EN 60439-1:1999) |
| DIN EN 60439-1-2005 |
低壓開關設備和控制設備組合裝置.第1部分:已通過型式試驗和部分型式試驗的組合裝置 |
|
| DIN EN 60439-2-2001 |
低壓開關設備和控制設備成套裝置.第2部分:母線干線系統的特殊要求(母線路)(IEC60439-2:2000) |
(Low-voltage switchgear and controlgear assemblies - Part 2: Particular requirements for busbar trunking systems (busways) (IEC 60439-2:2000); German version EN 60439-2:2000) |
| DIN EN 60439-3-2002 |
低壓開關設備和控制設備組合裝置.第3部分:安裝在非專業人員要進入使用場所的低壓開關設備和控制設備的組合 |
(Low-voltage switchgear and controlgear assemblies - Part 3: Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their use; Distribution boards (IEC 60439 |
| DIN EN 60439-4 Berichtigung 2-2004 |
對DIN EN 60439-4 (VDE 0660 Teil 501)-2000的勘誤 |
|
| DIN EN 60439-4-2000 |
低壓開關設備和控制設備組件.第4部分:施工現場用組件的特殊要求 |
(Low-voltage switchgear and controlgear assemblies - Part 4: Particular requirements for assemblies for construction sites (ACS) (IEC 60439-4:1990:1990 + A1:1995 + A2:1999); German version EN 60439-4:1991 + A1:1995 + A2:1999) |
| DIN EN 60439-4-2005 |
低壓開關設備和控制設備組合裝置.第4部分:施工現場用組合裝置(ACS)的特殊要求 |
|
| DIN EN 60439-5-1997 |
低壓開關設備和控制設備組件.第5部分:室外公共場所安裝用低壓開關組件的特殊要求.供電網絡用電力分配電纜交 |
(Low-voltage switchgear and controlgear assemblies - Part 5: Particular requirements for assemblies intended to be installed outdoors in public places; cable distribution cabinets (CDCs) for power distribution networks (IEC 60439-5:1996); German version E |
| DIN EN 60439-5/A1-1999 |
低壓開關設備和控制設備組件.第5部分:室外公共場所安裝用低壓開關組件的特殊要求.供電網絡用電力分配電纜交 |
(Low-voltage switchgear and controlgear assemblies - Part 5: Particular requirements for assemblies intended to be installed outdoors in public places; cable distribution cabinets (CDCs) for power distribution in networks; Amendment A1 (IEC 60439-5:1996/A |
| DIN EN 60442-1999 |
家用和類似用途的電面包烘烤器.使用性能的測量方法 |
(Electric toasters for household and similar purposes - Methods for measuring the performance (IEC 60442:1998); German version EN 60442:1998) |
| DIN EN 60444-1-2000 |
用π型網絡的零相位技術測量石英晶體單的參數.第1部分:用π型網絡的零相位技術測量石英晶體單的諧振頻 |
(Measurement of quartz crystal unit parameters by zero phase technique in a -network - Part 1: Basic method for the measurement of resonance frequency and resonance resistance of quartz crystal units by zero phase technique in a -network (IEC 60444-1:1986 |
| DIN EN 60444-2-1997 |
用π型網絡的零相位技術測量石英諧振器參數.第2部分:測量石英諧振器的動態電容的相位偏離法 |
(Measurement of quartz crystal unit parameters by zero phase technique in a pi-network - Part 2: Phase offset method for measurement of motional capacitance of quartz crystal units (IEC 60444-2:1980); German version EN 60444-2:1997) |
| DIN EN 60444-3-1997 |
用π型網絡的零相位技術測量石英諧振器參數.第3部分:用與并聯電容量Co補償相連的π網絡相位技術測量200MHz |
(Measurement of quartz crystal unit parameters by zero phase technique in a pi-network - Part 3: Basic method for the measurement of two-terminal parameters of quartz crystal units up to 200 MHz by phase technique in a pi-network with compensation of the |
| DIN EN 60444-4-1997 |
用π型網絡的零相位技術測量石英諧振器參數.第4部分:石英晶體件負荷諧振頻率fl、負荷諧振電阻Rl的測量方 |
(Measurement of quartz crystal unit parameters by zero phase technique in a pi-network - Part 4: Method for the measurement of the load resonance frequency f, load resonance resistance R and the calculation of other derived values of quartz crystal units, |
| DIN EN 60444-5-1997 |
石英諧振器參數測量.第5部分:用自動網絡分析儀和誤差修正技術評定電氣參數的測量方法 |
(Measurement of quartz crystal unit parameters - Part 5: Methods for the determination of equivalent electrical parameters using automatic network analyser techniques and error correction (IEC 60444-5:1995); German version EN 60444-5:1997) |
| DIN EN 60444-6-1997 |
石英諧振器參數測量.第6部分:取決于負載的測量 |
(Measurement of quartz crystal unit parameters - Part 6: Measurement of drive level dependence (DLD) (IEC 60444-6:1995); German version EN 60444-6:1997) |
| DIN EN 60444-7-2004 |
石英晶體件參數的測量.第7部分:石英晶體件的活性和頻率下降的測量 |
|
| DIN EN 60444-8-2004 |
石英晶體件參數的測量.第8部分:表面安裝的石英晶體件用測試工具 |
|
| DIN EN 60445-2000 |
人機接口、標記和識別的基本與安全原則.設備終端和用相應符號標記的接線端子的識別方法(包括字母數字系統的 |
(Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals and of terminations of certain designated conductors, including general rules of an alphanumeric system (IEC 60445:1999); German ver |
| DIN EN 60446-1999 |
人機接口的基本和安全規則.用顏色和數字對導線作標志 |
(Basic and safety principles for man-machine interface, marking and identification - Identification of conductors by colours or numerals (IEC 60446:1999); German version EN 60446:1999) |
| DIN EN 60447-1994 |
人機接口(MMI).操縱原理 |
(Man-machine interface (MMI); actuating principles (IEC 60447:1993); German version EN 60447:1993) |
| DIN EN 60447-2004 |
人機界面(MMI)、標記和標識的基礎和安全原則.操作原則 |
|
| DIN EN 60454 Bb.1-1999 |
電工用自粘膠帶.相關標準目錄.類型比較 |
(Pressure-sensitive adhesive tapes for electrical purposes - List of relevant standards, comparison of types (status as of 1999)) |
| DIN EN 60454-1-1997 |
電工用自粘電線膠布帶規范.第1部分:一般要求 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Part 1: General requirements (IEC 60454-1:1992); German version EN 60454-1:1994) |
| DIN EN 60454-2-1997 |
電工用自粘電線膠布帶規范.第2部分:試驗方法 |
(Specification for pressure-sensitive adhesive tapes for electrical purposes - Part 2: Methods of test (IEC 60454-2:1994); German version EN 60454-2:1995) |
| DIN EN 60454-3-1-2002 |
電工用壓敏粘帶.第3部分:單項材料規范.第1活頁:聚氯乙烯薄膜壓敏粘帶 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 1: PVC film tapes with pressure-sensitive adhesive (IEC 60454-3-1:1998 + A1:2001); German version EN 60454-3-1:1998 + A1:2001) |
| DIN EN 60454-3-10-1997 |
電工用自粘電線膠布帶.第3部分:單項材料規范.活頁10:帶有橡膠制熱固性膠的乙酸丁酸纖維素薄膜膠粘帶的要求 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; sheet 10: Requirements for cellulose-acetate-butyrate film tapes with rubber thermosetting adhesive (IEC 60454-3-10:1995); German version EN 6045 |
| DIN EN 60454-3-11-1999 |
電工用自粘膠帶.第3部分:單項材料規范.第11頁:帶熱固橡膠膠粘材料的皺折纖維素紙和聚乙烯對酞酸鹽薄膜合成 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 11: Combined tapes made of creped cellulosic paper and polyethylene terephthalate film with rubber thermosetting adhesive (IEC 60454-3-11:1 |
| DIN EN 60454-3-12-1999 |
電工用自粘膠帶.第3部分:單項材料規范.第12頁:聚乙烯薄膜自粘膠帶 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 12: Polyethylene film tapes with pressure-sensitive adhesive (IEC 60454-3-12:1998); German version EN 60454-3-12:1998) |
| DIN EN 60454-3-13-1997 |
電工用壓敏膠粘帶.第3部分:單項材料的規范.活頁13:帶有一面是熱塑料,另一面是熱固橡膠粘接材料的粘膠斷纖維 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; sheet 13: Requirements for combined cellulose-viscose woven fabric tapes, one side recovered with thermoplastic material, the other side with rub |
| DIN EN 60454-3-14-2002 |
電工用壓敏粘帶.第3部分:單項材料規范.活頁14:涂壓敏粘合劑的聚四氟乙烯薄膜帶(IEC60454-3-14:2001) |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 14: Polytetrafluoroethylene film tapes with pressure-sensitive adhesive (IEC 60454-3-14:2001); German version EN 60454-3-14:2001) |
| DIN EN 60454-3-15-2002 |
電工用壓敏粘帶.第3部分:單項材料規范.活頁15:涂橡膠熱塑粘合劑的聚酯膜/聚酯無編織復合帶(IEC60454-3-15:2 |
() |
| DIN EN 60454-3-16-2004 |
電工用壓敏粘帶.第3部分:單項材料的規范.第16活頁:涂壓敏粘合劑的聚脂薄膜/玻璃絲復合帶 |
|
| DIN EN 60454-3-17-2002 |
電工用壓敏粘帶.第3部分:單項材料規范.活頁17:涂壓敏粘合劑的聚酯和環氧復合(IEC60454-3-17:2001).德文版EN |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 17: Polyester/epoxy combinations with pressure-sensitive adhesive (IEC 60454-3-17:2001); German version EN 60454-3-17:2001) |
| DIN EN 60454-3-18-2004 |
電工用壓敏粘帶.第3部分:單項材料的規范.第18活頁:涂壓敏粘合劑的聚丙烯薄膜帶 |
|
| DIN EN 60454-3-19-2004 |
電工用壓敏粘帶.第3部分:單項材料的規范.第19活頁:雙面涂壓敏粘合劑的不同襯底材料制粘帶 |
|
| DIN EN 60454-3-2-1999 |
電工用自粘膠帶.第3部分:單項材料的規范.第2頁:帶熱固橡膠的或交聯丙烯粘合的丙烯粘合的聚脂薄膜帶 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 2: Polyester film tapes with rubber thermosetting or acrylic crosslinked adhesives (IEC 60454-3-2:1998); German version EN 60454-3-2:1998) |
| DIN EN 60454-3-3-1999 |
電工用自粘膠帶.第3部分:單項材料規范.第3頁:帶熱固橡膠粘合材料的聚酯薄膜帶 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 3: Polyester film tapes with rubber thermoplastic adhesive (IEC 60454-3-3:1998); German version EN 60454-3-3:1998) |
| DIN EN 60454-3-4-1999 |
電工用自粘膠帶.第3部分:單項材料規范.第4頁:帶熱固橡膠粘合材料的纖維素皺紋紙 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 4: Cellulosic paper, creped, with rubber thermosetting adhesive (IEC 60454-3-4:1998); German version EN 60454-3-4:1998) |
| DIN EN 60454-3-5-1999 |
電工用自粘膠帶.第3部分:單項材料規范.第5頁:帶熱固橡膠粘合材料的纖維素非皺紋紙 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 5: Cellulosic paper, non-creped, with rubber thermosetting adhesive (IEC 60454-3-5:1998); German version EN 60454-3-5:1998) |
| DIN EN 60454-3-6-1999 |
電工用自粘膠帶.第3部分:單項材料規范.第6頁:帶熱塑丙烯酸膠粘劑的聚碳酸脂薄膜帶 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 6: Polycarbonate film tapes with acrylic thermosetting adhesive (IEC 60454-3-6:1998); German version EN 60454-3-6:1998) |
| DIN EN 60454-3-7-1999 |
電工用自粘膠帶.第3部分:單項材料規范.第7頁:聚酰亞胺薄膜自粘膠帶 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 7: Polyimide film tapes with pressure-sensitive adhesive (IEC 60454-3-7:1998); German version EN 60454-3-7:1998) |
| DIN EN 60454-3-8-1999 |
電工用自粘膠帶.第3部分:單項材料規范.第8頁:玻璃布自粘膠帶 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 8: Glass fabric with pressure-sensitive adhesive (IEC 60454-3-8:1998); German version EN 60454-3-8:1998) |
| DIN EN 60454-3-9-1999 |
電工用自粘膠帶.第3部分:單項材料規范.第9頁:帶熱固橡膠較粘材料的醋酸纖維素織帶 |
(Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 9: Cellulose acetate woven fabric tapes with rubber thermosetting adhesive (IEC 60454-3-9:1998); German version EN 60454-3-9:1998) |
| DIN EN 60455-1-1999 |
電器絕緣用反應性樹脂化合物.第1部分:定義和一般要求 |
(Resin based reactive compounds used for electrical insulation - Part 1: Definitions and general requirements (IEC 60455-1:1998); German version EN 60455-1:1998) |
| DIN EN 60455-2-2000 |
電器絕緣用反應性樹脂化合物.第2部分:試驗方法 |
(Resin based reactive compounds used for electrical insulation - Part 2: Methods of test (IEC 60455-2:1998); German version EN 60455-2:1999) |
| DIN EN 60455-3-1-2004 |
電絕緣用樹脂基反應性復合物.第3部分:單項材料規范.活頁1:未填充環氧樹脂復合物 |
(Resin based reactive compounds used for electrical insulation - Part 3: Specifications for individual materials - Sheet 1: Unfilled epoxy resinous compounds (IEC 60455-3-1:2003); German version EN 60455-3-1:2003) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com