標準號 |
中文名稱 |
英文名稱 |
| EN 12704-1999 |
紙、紙板、包裝和易處置衛生品用粘合劑含水膠粘劑起泡性的測定 |
Adhesives for paper and board, packaging and disposable sanitary products - Determination of foam formation for aqueous adhesives |
| EN 12705-1999 |
皮革和鞋靴材料粘合劑用遷移法對白色或鮮艷色皮革表面顏色變化的測定 |
Adhesives for leather and footwear materials - Determination of colour change of white or bright coloured leather surfaces by migration |
| EN 12706-1999 |
膠粘劑不凝地板光滑劑和/或均化劑的試驗方法流動特性的測定 |
Adhesives - Test methods for hydraulic setting floor smoothing and/or levelling compounds - Determination of flow characteristics |
| EN 12707-1999 |
塑料桶公稱容量為210升、220升和225升的非移動頭式(敞口)桶 |
Plastics drums - Non-removable head (tight head) drums with a nominal capacity of 210 l, 220 l and 225 l |
| EN 12708-2000 |
公稱容量為20升至225升的塑料容器用塞/蓋封閉系統 |
Plug/bung closure systems for plastics containers with a nominal capacity of 20 l to 225 l |
| EN 12709-2000 |
塑料桶標稱容量20升到120升的非移動頭（敞口）桶 |
Plastics drums - Non-removable head (tight head) circular cross-section drums with a nominal capacity of 20 l to 120 l |
| EN 1271-2004 |
運動場地器材.排球設備.功能和安全要求及試驗方法 |
|
| EN 12710-1999 |
纖維板柱桶公稱容量為15升至250升的帶封閉環的可移動頭(開口)式桶 |
Fibreboard drums - Removable head (open head) drums with closing rings with a nominal capacity of 15 l to 250 l |
| EN 12711-2000 |
鋼制桶最小總?cè)萘繛椋玻常吧姆且苿?dòng)頭（敞口）鋼桶 |
Steel drums - Non-removable head (tight head) drums with a minimum total capacity of 230 l |
| EN 12713-2000 |
公稱容積20升至60升的塑料容器用螺旋帽閉合系統 |
Screw cap closure systems for plastics containers with a nominal capacity of 20 l to 60 l |
| EN 12714-2000 |
塑料柱桶額定容量為25升至220升的可移動頭(開口)桶 |
Plastics drums - Removable head (open head) drums with a nominal capacity of 25 l to 220 l |
| EN 12715-2000 |
特殊土工作業的實施灌漿 |
Execution of special geotechnical works - Grouting |
| EN 12716-2001 |
特殊土工作業的實施噴漿 |
Execution of special geotechnical works - Jet grouting |
| EN 12717-2001 |
機床安全鉆床 |
Safety of machine tools - Drilling machines |
| EN 1272-1998 |
兒童保育產品 連椅桌 安全要求和試驗方法 |
Child care articles - Table mounted chairs - Safety requirements and test methods |
| EN 12720-1997 |
家具表面耐冷液性能的評定（ＩＳＯ４２１１：１９７９修訂） |
Furniture - Assessment of surface resistance to cold liquids (ISO 4211:1979 modified) |
| EN 12721-1997 |
家具表面耐濕熱性能的評定（ＩＳＯ４２１１－２：１９９３修訂） |
Furniture - Assessment of surface resistance to wet heat (ISO 4211-2:1993 modified) |
| EN 12722-1997 |
家具表面耐干熱性能的評定（ＩＳＯ４２１１－３：１９９３修訂） |
Furniture - Assessment of surface resistance to dry heat (ISO 4211-3:1993 modified) |
| EN 12723-2000 |
液泵泵和設備的通用術語 定義、參數、字母符號和單位 |
Liquid pumps - General terms for pumps and installations - Definitions, quantities, letter symbols and units |
| EN 12726-2000 |
包裝軟木塞和回頭明顯的瓶口用口徑為18.5mm的塞軟木塞的瓶口 |
Packaging - Cork mouth finish with a bore diameter of 18,5 mm for corks and temper evident capsules |
| EN 12727-2000 |
家具排坐椅強度和耐用性要求和試驗方法 |
Furniture - Ranked seating - Test methods and requirements for strength and durability |
| EN 12728-1999 |
表面活性劑起泡能力的測定多孔盤打拍法 |
Surface active agents - Determination of foaming power - Perforated disc beating method |
| EN 12729-2002 |
防止飲用水回流污染的裝置 減壓區可控的防回流裝置B類A型 |
Devices to prevent pollution by backflow of potable water - Controllable backflow preventer with reduced pressure zone - Family B; Type A |
| EN 1273-2001 |
兒童保育產品 嬰兒助行架 安全要求和試驗方法 |
Child care articles - Baby walking frames - Safety requirements and test methods |
| EN 12730-2001 |
防水軟薄板屋面防水用瀝青塑料和橡膠薄板抗靜負荷性能的測定 |
Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to static loading |
| EN 12732-2000 |
燃?xì)夤⿷?yīng)系統焊接鋼管功能要求 |
Gas supply systems - Welding steel pipework - Functional requirements |
| EN 12733-2001 |
農業和林業機械步行電動割草機安全 |
Agricultural and forestry machinery - Pedestrian controlled motor mowers - Safety |
| EN 12734-2000 |
灌溉技術可移動灌溉設備用快速連接管技術特性和試驗 |
Irrigation techniques - Quick coupling pipes for movable irrigation supply - Technical characteristics and testing |
| EN 12735-1-2001 |
銅和銅合金空調和制冷用無縫圓銅管第１部分：管道系統用管子 |
Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems |
| EN 12735-2-2001 |
銅和銅合金空調和制冷用無縫圓銅管第２部分：設備用管子 |
Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 2: Tubes for equipment |
| EN 12736-2001 |
電動道路車輛用車載充電器充電過程中車輛的在空中噪聲聲功率級的測定 |
Electrically propelled road vehicles - Airborne acoustical noise of vehicle during charging with on-board chargers - Determination of sound power level |
| EN 12737-2004 |
預制混凝土產品.家畜用地板橫木 |
|
| EN 12738-1999 |
生物技術研究、開發和分析用實驗室作實驗時給動物接種微生物的動物的隔離的指南 |
Biotechnology - Laboratories for research, development and analysis - Guidance for containment of animals inoculated with microorganisms in experiments |
| EN 1274-1996 |
熱噴涂 粉末、成份、交貨技術條件 |
Thermal spraying - Powders - Composition - Technical supply conditions |
| EN 1274-2004 |
熱噴涂.粉末.成分、交貨技術條件 |
|
| EN 12740-1999 |
生物技術研究、開發和分析用實驗室廢料的處理、滅活和檢驗指南 |
Biotechnology - Laboratories for research, development and analysis - Guidance for handling, inactivating and testing of waste |
| EN 12741-1999 |
生物技術研究、開發與分析用實驗室生物技術實驗室操作指南 |
Biotechnology - Laboratories for research, development and analysis - Guidance for biotechnology laboratory operations |
| EN 12742-1999 |
果汁和蔬菜汁游離氨基酸含量的測定液體色譜法 |
Fruit and vegetable juices - Determination of the free amino acids content - Liquid chromatographic method |
| EN 12743-1999 |
鞋類外底的試驗方法抗壓能力 |
Footwear - Test methods for outsoles - Compression energy |
| EN 12744-1999 |
鞋類內底的試驗方法抗脫膠性 |
Footwear - Test methods for insoles - Delamination resistance |
| EN 12745-1999 |
鞋類內底的試驗方法鞋跟釘系牢度 |
Footwear - Test methods for insoles - Heel pin holding strength |
| EN 12746-2000 |
鞋類內底和鞋里幫的試驗方法水的吸收性和脫水性 |
Footwear - Test methods for insoles and insocks - Water absorption and desorption |
| EN 12747-1999 |
鞋類內底的試驗方法抗磨性 |
Footwear - Test methods for insoles - Abrasion resistance |
| EN 12748-1999 |
鞋類外底、內底、鞋襯和鞋里幫的試驗方法水溶性物質含量 |
Footwear - Test methods for outsoles, insoles, lining and insocks - Water soluble content |
| EN 12749-1999 |
鞋類老化條件 |
Footwear - Ageing conditioning |
| EN 1275-1997 |
化學消毒劑和防腐劑 堿性真菌活性 檢驗方法和要求(第1階段) |
Chemical disinfectants and antiseptics - Basic fungicidal activity - Test method and requirements (Phase 1) |
| EN 12750-2001 |
木工機械的安全四邊制模機械 |
Safety of woodworking machines - Four-sided moulding machines |
| EN 12751-1999 |
紡織品試驗用纖維、紗和織物的抽樣 |
Textiles - Sampling of fibres, yarns and fabrics for testing |
| EN 12752-1-1999 |
標稱熱輸入不超過20kW的B型燃?xì)鉂L動烘干機第1部分：安全 |
Gas-fired type B tumble dryers of nominal heat input not exceeding 20 kW - Part 1: Safety |
| EN 12752-2-1999 |
標稱熱輸入不超過20kW的B型滾動烘干機能量的合理利用 |
Gas-fired type B tumble dryers of nominal heat input not exceeding 20 kW - Part 2: Rational use of energy |
| EN 12754-2001 |
可移動的氣瓶溶解乙炔用氣瓶灌裝時的檢查 |
Transportable gas cylinders - Cylinders for dissolved acetylene - Inspection at time of filling |
| EN 12755-2000 |
可移動氣瓶乙炔灌裝條件 |
Transportable gas cylinders - Filling conditions for acetylene bundles |
| EN 12756-2000 |
機械密封主要尺寸、標識和材料編碼 |
Mechanical seals - Principal dimensions, designation and material codes |
| EN 12758-2002 |
建筑玻璃裝玻璃和隔聲產品描述和性能的測定 |
Glass in building - Glazing and airborne sound insulation - Product descriptions and determination of properties |
| EN 12759-2001 |
涂橡膠或塑料涂織物耐液體性能 |
Rubber- or plastic-coated fabrics - Determination of resistance to liquids |
| EN 1276-1997 |
化學消毒劑和防腐劑 用在食品、工業、家用、和公共區域的化學消毒劑和防腐劑的微生物活性評估的定量懸浮實 |
Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of bactericidal activity of chemical disinfectants and antiseptics used in food, industrial, domestic, and institutional areas - Test method and requirements (Phase2) |
| EN 12760-1999 |
閥門 鋼閥門套接焊接端 |
Valves - Socket welding ends for steel valves |
| EN 12761-1-2001 |
農業和林業機械 噴霧器和液體肥料撒布機 環境保護 第1部分：總則 |
Agricultural and forestry machinery - Sprayers and liquid fertilizer distributors; Environmental protection - Part 1: General |
| EN 12761-2-2001 |
農業和林業機械 噴霧器和液態肥料撒布機 環境保護 第2部分：田間作物噴霧器 |
Agricultural and forestry machinery - Sprayers and liquid fertilizer distributors; Environmental protection - Part 2: Field crop sprayers |
| EN 12761-3-2001 |
農業和林業機械 噴霧器和液態肥料撒布機 環境保護 第3部分：灌木和喬木作物用空氣助動式噴霧器 |
Agricultural and forestry machinery - Sprayers and liquid fertilizer distributors; Environmental protection - Part 3: Air-assisted sprayers for bush and tree crops |
| EN 12763-2000 |
建筑物排水系統的纖維膠合管及附件 交貨尺寸和技術術語 |
Fibre-cement pipes and fittings for discharge systems for buildings - Dimensions and technical terms of delivery |
| EN 12765-2001 |
非建筑應用中熱固性木膠的分類 |
Classification of thermosetting wood adhesives for non-structural applications |
| EN 12766-1-2000 |
石油制品和廢油 PCBs和相關產品的測定 第1部分：用電子俘獲探測器（ECD）通過氣相色譜分析（GC）法分離和 |
Petroleum products and used oils - Determination of PCBs and related products - Part 1: Separation and determination of selected PCB congeners by gas chromatography (GC) using an electron capture detector (ECD) |
| EN 12766-2-2001 |
石油制品和廢油 PCBs和相關產品的測定 第2部分：多氯化聯二苯（PCB）含量計算 |
Petroleum products and used oils - Determination of PCBs and related products - Part 2: Calculation of polychlorinated biphenyl (PCB) content |
| EN 12766-3-2004 |
石油產品和用過的油.多氯聯苯和相關產品的測定.第3部分:用電子俘獲探測器的氣相色譜法測定多氯三聯苯(PCT)和多氯甲苯((PCBT)含量 |
|
| EN 12767-2000 |
公路設備支承結構的被動安全 要求和試驗方法 |
Passive safety of support structures for road equipment - Requirements and test methods |
| EN 1277-1996 |
塑料管道系統 地下無壓用熱塑管道系統 彈性密封環型接頭密封性試驗方法 |
Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints |
| EN 12770-1999 |
鞋類 鞋底試驗方法 耐磨性 |
Footwear - Test methods for outsoles - Abrasion resistance |
| EN 12771-1999 |
鞋類 鞋底試驗方法 撕裂強度 |
Footwear - Test methods for outsoles - Tear strength |
| EN 12772-1999 |
鞋類 鞋底試驗方法 尺寸穩定性 |
Footwear - Test methods for outsoles - Dimensional stability |
| EN 12773-1999 |
鞋類 鞋底試驗方法 針刺裂強度 |
Footwear - Test methods for outsoles - Needle tear strength |
| EN 12774-1999 |
鞋類 鞋底試驗方法 裂口撕裂強度和抗分層阻力的測定 |
Footwear - Test methods for outsoles - Determination of split tear strength and delamination resistance |
| EN 12775-2001 |
實心木板 分類和術語 |
Solid wood panels - Classification and terminology |
| EN 12778-2002 |
炊具 家用壓力炊具 |
Cookware - Pressure cookers for domestic use |
| EN 12779-2004 |
木材加工機械安全.帶固定裝置的碎片和灰塵排出系統.性能相關安全和安全要求 |
|
| EN 12779-2004 |
木材加工機械安全.帶固定裝置的碎片和灰塵排出系統.性能相關安全和安全要求 |
|
| EN 1278-1998 |
民用水處理用化學藥劑 臭氧 |
Chemicals used for treatment of water intended for human consumption - Ozone |
| EN 1278/prA1-2000 |
民用水處理用化學藥劑 臭氧 修正A1 |
Chemicals used for treatment of water intended for human consumption - Ozone; Amendment A1 |
| EN 12780-2002 |
水質 通過膜濾除法檢測和統計假單胞銅綠菌 |
Water quality - Detection and enumeration of Pseudomonas aeruginosa by membrane filtration |
| EN 12781-2001 |
墻面覆蓋層 軟木板規范 |
Wallcoverings - Specification for cork panels |
| EN 12782-1999 |
鞋類 鞋墊試驗方法 抗縫合撕裂阻力 |
Footwear - Test methods for insoles - Resistance to stitch tear |
| EN 12784-1999 |
鞋類 整鞋試驗方法 保溫 |
Footwear - Test methods for whole shoe - Thermal insulation |
| EN 12785-2000 |
鞋類 整鞋試驗方法 鞋跟固定 |
Footwear - Test methods for whole shoe - Heel attachment |
| EN 12786-1999 |
機械安全性 安全標準振動條款起草指南 |
Safety of machinery - Guidance for the drafting of the vibration clauses of safety standards |
| EN 12789-2002 |
高級工藝陶瓷 空氣、大氣壓的空氣中陶瓷合成物的高溫機械性能 抗彎強度測定 |
Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under air at atmospheric pressure - Determination of flexural strength |
| EN 1279-1-2004 |
建筑玻璃.絕緣玻璃組件.第1部分:概論、尺寸公差和系統描述規則 |
|
| EN 1279-2-2002 |
建筑玻璃 隔離玻璃裝置 第2部分：透潮性長期試驗方法和要求 |
Glass in building - Insulating glass units - Part 2: Long term test method and requirements for moisture penetration |
| EN 1279-3-2002 |
建筑玻璃 隔離玻璃裝置 第3部分：漏氣率和氣體濃度容差的長期試驗方法和要求 |
Glass in building - Insulating glass units - Part 3: Long term test method and requirements for gas leakage rate and for gas concentration tolerances |
| EN 1279-4-2002 |
建筑玻璃 隔離玻璃裝置 第4部分：邊緣密封物理特性的試驗方法 |
Glass in building - Insulating glass units - Part 4: Methods of test for the physical attributes of edge seals |
| EN 1279-6-2002 |
建筑玻璃 隔離玻璃裝置 第6部分：工廠生產控制及周期試驗 |
Glass in building - Insulating glass units - Part 6: Factory production control and periodic tests |
| EN 12790-2002 |
兒童看護用品 斜倚式搖籃 |
Child care articles - Reclined cradles |
| EN 12792-2003 |
建筑物通風 符號、術語和圖形符號 |
Ventilation for buildings - Symbols, terminology and graphical symbols |
| EN 12795-2003 |
公路交通和運輸通信和信息處理技術 專用近程通訊（DSRC） DSRC數據鏈路層 媒體訪問和邏輯鏈路控制 |
Road transport and traffic telematics - Dedicated Short Range Communication (DSRC) - DSRC Data link layer: Medium access and logical link control |
| EN 12797-2000 |
銅焊 銅焊接頭的破壞性試驗 |
Brazing - Destructive tests of brazed joints |
| EN 12798-1999 |
運輸質量體系 公路、鐵路以及內河運輸 有關危險品運輸安全性的EN ISO 9002增補質量體系要求 |
Transport Quality System - Road, rail and inland navigation transport - Quality system requirements to supplement EN ISO 9002 for the transport of dangerous goods with regard to safety |
| EN 12799-2000 |
銅焊 銅焊接頭的破壞性試驗 |
Brazing - Non-destructive examination of brazed joints |
| EN 12800-2000 |
鞋類 鞋墊試驗方法 尺寸穩定性 |
Footwear - Test methods for insoles - Dimensional stability |
| EN 12801-2000 |
鞋類 鞋墊、襯里和襯墊試驗方法 耐汗性 |
Footwear - Test methods for insoles, lining and insocks - Perspiration resistance |
| EN 12802-2000 |
道路標志材料 實驗室識別方法 |
Road marking materials - Laboratory methods for identification |
| EN 12803-2000 |
鞋類 鞋底試驗方法 抗拉強度和伸長率 |
Footwear - Test methods for outsoles - Tensile strength and elongation |
| EN 12805-2002 |
機動車液化石油氣（LPG）構件 容器 |
Automotive LPG components - Containers |
| EN 12806-2003 |
機動車液化石油氣（LPG）構件 罐以外的其它容器 |
Automative liquefied petroleum gas components - Other than containers |
| EN 12807-2001 |
可移動再充式液化石油氣（LPG）銅焊鋼瓶 設計和構造 |
Transportable refillable brazed steel cylinders for liquefied petroleum gas (LPG) - Design and construction |
| EN 12808-1-1999 |
瓷磚用粘合劑和灰漿 第1部分：反應樹脂砂漿耐化學腐蝕性測定 |
Adhesives and grouts for tiles - Part 1: Determination of chemical resistance of reaction resin mortars |
| EN 12808-2-2001 |
瓷磚用灰漿 第2部分：耐磨性測定 |
Grouts for tiles - Part 2: Determination of resistance to abrasion |
| EN 12808-3-2001 |
瓷磚用灰漿 第3部分：抗彎和耐壓強度測定 |
Grouts for tiles - Part 3: Determination of flexural and compressive strength |
| EN 12808-4-2001 |
瓷磚用灰漿 第4部分：收縮性測定 |
Grouts for tiles - Part 4: Determination of shrinkage |
| EN 12808-5-2001 |
瓷磚用灰漿 第5部分：吸水性測定 |
Grouts for tiles - Part 5: Determination of water absorption |
| EN 1281-2-1995 |
麻醉和呼吸設備 圓錐形接頭 第2部分：螺紋承重連接頭 |
Anaesthetic and respiratory equipment - Conical connectors - Part 2: Screw-threaded weight-bearing connectors (ISO 5356-2:1987 modified) |
| EN 12811-2-2004 |
臨時工作設備.第2部分:材料的信息 |
|
| EN 12811-3-2002 |
臨時性工程設備 腳手架 第3部分：負荷試驗 |
Temporary works equipment - Part 3: Load testing |
| EN 12812-2004 |
腳手架.性能要求和一般設計 |
|
| EN 12813-2004 |
臨時工程設備.預制構件的承載塔.結構設計的特殊要求 |
|
| EN 12814-2-2000 |
熱塑性塑料半成品的焊接接頭試驗 第2部分：拉伸試驗 |
Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test |
| EN 12814-3-2000 |
熱塑性塑料半成品的焊接接頭試驗 第3部分：拉伸蠕變?cè)囼?yàn) |
Testing of welded joints of thermoplastics semi-finished products - Part 3: Tensile creep test |
| EN 12814-4-2001 |
熱塑性塑料半成品的焊接接頭試驗 第4部分：剝落試驗 |
Testing of welded joints of thermoplastics semi-finished products - Part 4: Peel test |
| EN 12814-5-2000 |
熱塑性塑料半成品的焊接接頭試驗 第5部分：目測 |
Testing of welded joints of thermoplastics semi-finished - Part 5: Macroscopic examination |
| EN 12814-6-2000 |
熱塑性塑料半成品的焊接接頭試驗 第6部分：低溫拉伸試驗 |
Testing of welded joints of thermoplastics semi-finished products - Part 6: Low temperature tensile test |
| EN 12814-7-2002 |
熱塑性塑料半成品的焊接接頭試驗 第7部分：采用腰形試樣的拉伸試驗 |
Testing of welded joints of thermoplastics semi-finished products - Part 7: Tensile test with waisted test specimens |
| EN 12815-2004 |
家用固體燃料炊具.要求和試驗方法 |
|
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com