標準號 |
中文名稱 |
英文名稱 |
| BS EN 674-1998 |
建筑物用玻璃.熱傳遞系數(U值)測定.保護熱平板法 |
(Glass in building - Determination of thermal transmittance (U value) - Guarded hot plate method) |
| BS EN 675-1998 |
建筑物用玻璃.熱傳遞系數(U值)測定.熱流計法 |
(Glass in building - Determination of thermal transmittance (U value) - Heat flow meter method) |
| BS EN 676-2003 |
氣體燃料用自動強制送風燃燒器 |
(Automatic forced draught burners for gaseous fuels) |
| BS EN 677-1998 |
燃氣集中加熱鍋爐.標稱熱輸入不超過70KW凝汽式鍋爐的特殊要求 |
(Gas-fired central heating boilers - Specific requirements for condensing boilers with a nominal heat input not exceeding 70 kW) |
| BS EN 678-1994 |
熱壓處理過的加氣混凝土的干密度測定 |
(Determination of the dry density of autoclaved aerated concrete) |
| BS EN 679-1994 |
熱處理過的加氣混凝土的抗壓強度的測定 |
(Determination of the compressive strength of autoclaved aerated concrete) |
| BS EN 679-2005 |
高壓蒸養加氣混凝土的抗壓強度測定 |
|
| BS EN 680-1994 |
熱壓處理過的加氣混凝土的干燥收縮的測定 |
(Determination of the drying shrinkage of autoclaved aerated concrete) |
| BS EN 681-1-1996 |
彈性密封件.水和污水設施用管聯接密封件的材料要求.琉化橡膠 |
(Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Vulcanized rubber) |
| BS EN 681-2-2000 |
彈性密封件.輸水和污水設施用管聯接密封件的材料要求.熱塑性彈性件 |
(Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Thermoplastic elastomers) |
| BS EN 681-3-2000 |
彈性密封件.輸水和污水設施用管聯接密封件的材料要求.硫化橡膠的多孔材料 |
(Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Cellular materials of vulcanized rubber) |
| BS EN 681-4-2000 |
彈性密封件.輸水和污水設施用管聯接密封件的材料要求.聚氨酯鑄造密封件 |
(Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Cast polyurethane sealing elements) |
| BS EN 682-2002 |
彈性密封件.運送氣體和液態碳氫化合物的管件及配件中所用密封件的材料要求 |
(Elastomeric seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids) |
| BS EN 683-1-1996 |
鋁和鋁合金.葉片坯料.檢驗和驗收技術條件 |
(Aluminium and aluminium alloys - Finstock - Technical conditions for inspection and delivery) |
| BS EN 683-2-1997 |
鋁和鋁合金.散熱片坯料.機械特性 |
(Aluminium and aluminium alloys - Finstock - Mechanical properties) |
| BS EN 683-3-1997 |
鋁和鋁合金.散熱片坯料.尺寸公差 |
(Aluminium and aluminium alloys - Finstock - Tolerances on dimensions and form) |
| BS EN 684-1996 |
彈性地板覆蓋物.密封強度測定 |
(Resilient floor coverings - Determination of seam strength) |
| BS EN 685-1996 |
彈性和疊層地板覆蓋物.分類 |
(Resilient and laminate floor coverings - Classification) |
| BS EN 686-1997 |
油氈覆面層.泡沫襯油氈的規范 |
(Resilient floor coverings - Specification for plain and decorative linoleum on a foam backing) |
| BS EN 687-1997 |
彈性地板覆蓋物.軟木襯平面和裝飾油氈規范 |
(Resilient floor coverings - Specification for plain and decorative linoleum on a corkment backing) |
| BS EN 688-1997 |
彈性地板覆蓋物.軟木襯油氈規范 |
(Resilient floor coverings - Specification for corklinoleum) |
| BS EN 689-1996 |
工作場所的氣氛.為與極限值比較和測量對策用評定化學試劑影響的導則 |
(Workplace atmospheres - Guidance for the assessment of exposure by inhalation to chemical agents for comparison with limit values and measurement strategy) |
| BS EN 690-1995 |
農用機械.糞肥撒布機.安全 |
(Agricultural machinery - Manure spreaders - Safety) |
| BS EN 692-1997 |
機械壓力機.安全 |
(Mechanical presses - Safety) |
| BS EN 693-2001 |
機床.安全.液壓 |
(Machine tools - Safety - Hydraulic presses) |
| BS EN 694-2004 |
消防軟管.固定系統的半硬性軟管 |
|
| BS EN 695-1997 |
廚房洗池.聯接尺寸 |
(Kitchen sinks - Connecting dimensions) |
| BS EN 696-1995 |
一般用途纖維繩索.聚酰胺繩索 |
(Fibre ropes for general service - Polyamide) |
| BS EN 697-1995 |
一般用途纖維繩索.聚酯繩索 |
(Fibre ropes for general service - Polyester) |
| BS EN 698-1995 |
一般用途纖維繩索.粗麻繩和劍麻繩 |
(Fibre ropes for general service - Manila and sisal) |
| BS EN 699-1995 |
一般用途纖維繩索.聚丙烯繩 |
(Fibre ropes for general service - Polypropylene) |
| BS EN 700-1995 |
一般用途纖維繩索.聚乙烯繩 |
(Fibre ropes for general service - Polyethylene) |
| BS EN 701-1995 |
一般用途纖維繩索總規范 |
(Fibre ropes for general service - General specification) |
| BS EN 702-1995 |
防護服.防熱和防火.試驗方法.透過防護服或其材料傳輸?shù)慕佑|熱的測定 |
(Protective clothing - Protection against heat and flame - Test method - Determination of the contact heat transmission through protective clothing or its materials) |
| BS EN 703-1996 |
農業機械.青飼料切碎機.安全 |
(Agricultural machinery - Silage cutters - Safety) |
| BS EN 703-2004 |
農業機械.青飼料裝載、攪拌和/或切碎機和分配機器.安全 |
|
| BS EN 704-1999 |
農業機械.撿拾機具壓捆機.安全 |
(Agricultural machinery - Pick-up balers - Safety) |
| BS EN 705-1995 |
塑料管道系統.玻璃增強熱固性(GRP)塑料管和配件.回歸分析及其使用方法 |
(Plastics piping systems - Glass-reinforced thermosetting (GRP) pipes and fittings - Methods for regression analyses and their use) |
| BS EN 706-1997 |
農業機械.葡萄園用頂端噴射機械.安全 |
(Agricultural machinery - Vine shoot tipping machines - Safety) |
| BS EN 707-1999 |
農業機械.泥漿槽.安全 |
(Agricultural machinery - Slurry tankers - Safety) |
| BS EN 708-1997 |
農業機械.電力驅動的整地機械.安全 |
(Agricultural machinery - Soil working machines with powered tools - Safety) |
| BS EN 709-1997 |
農業和林業機械.帶有裝配好的旋轉式中耕機可在側面操縱的拖拉機,電動鋤具,帶驅動輪的電動鋤具 |
(Agricultural and forestry machinery - Pedestrian controlled tractors with mounted rotary cultivators, motor hoes, motor hoes with drive wheel(s) - Safety) |
| BS EN 71-1-2001 |
玩具的安全.機械及物理性能 |
(Safety of toys - Mechanical and physical properties) |
| BS EN 71-2-2003 |
玩具的安全.易燃性 |
(Safety of toys - Flammability) |
| BS EN 71-3-1995 |
玩具的安全性.某些部件的移動規范 |
(Safety of toys - Specification for migration of certain elements) |
| BS EN 71-4-1998 |
玩具的安全.化學和相關活性的試驗設備 |
(Safety of toys - Experimental sets for chemistry and related activities) |
| BS EN 71-5-1993 |
動玩具的安全性.實驗裝置除外的化學玩具 |
(Safety of toys - Chemical toys (sets) other than experimental sets) |
| BS EN 71-6-1995 |
玩具安全.年齡警告標志圖形符號 |
(Safety of toys - Graphical symbols for age warning labelling) |
| BS EN 71-7-2002 |
玩具安全.指甲油的要求和試驗方法 |
Safety of toys - Finger paints - Requirements and test methods |
| BS EN 71-8-2003 |
玩具安全.室內和室外家用秋千、滑梯和類似活動玩具 |
(Safety of toys - Swings, slides and similar activity toys for indoor and outdoor family domestic use) |
| BS EN 710-1998 |
鑄模,芯造機械,工廠及相關設備的安全要求 |
(Safety requirements for foundry moulding and coremaking machinery and plant and associated equipment) |
| BS EN 711-1996 |
內河航行船只.甲板圍欄.要求、型式 |
(Inland navigation vessels - Railings for decks - Requirements, types) |
| BS EN 712-1995 |
熱塑管道系統.壓力管和配件的機械接合.在恒定徑向力下抗拔出性能的試驗方法 |
(Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force) |
| BS EN 713-1995 |
塑料管道系統.配件和聚烯烴壓力管的機械接合.彎曲時組件內部壓力密封性的試驗方法 |
(Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending) |
| BS EN 714-1995 |
熱塑管道系統.壓力管和模塑配件的無端負載軸承彈性密封環型接合件.在無軸向推力時內部流體靜力學壓力下密封 |
(Thermoplastics piping systems - Non-end-load-bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings - Test method for leaktightness under internal hydrostatic pressur) |
| BS EN 715-1995 |
熱塑管道系統.小直徑壓力管和配件間端負荷軸承接合件.在包含端推力的內部水壓下密封性的試驗方法 |
(Thermoplastics piping systems - End-load-bearing joints between small diameter pressure pipes and fittings - Test method for leaktightness under internal water pressure, including end thrust) |
| BS EN 716-1-1996 |
家具.家用兒童帆布床和折疊床.安全要求 |
(Furniture - Children’s cots and folding cots for domestic use - Safety requirements) |
| BS EN 716-2-1996 |
家具.家用兒童帆布床和折疊床.試驗方法 |
Furniture - Children`s cots and folding cots for domestic use - Test methods |
| BS EN 717-1-2005 |
木基板材.甲醛釋出的測定.用燃燒室法測定甲醛的排放量 |
|
| BS EN 717-2-1995 |
木質板材.甲醛釋放量的測定.用氣體分析法測定甲醛釋放量 |
Wood-based panels - Determination of formaldehyde release - Formaldehyde release by the gas analysis method |
| BS EN 717-3-1996 |
木質板材.甲醛釋放量的測定.長頸瓶法測定甲醛釋放量 |
Wood-based panels - Determination of formaldehyde release - Formaldehyde release by the flask method |
| BS EN 718-1996 |
彈性覆面層.加強板或襯單位面積質量的測定 |
Resilient floor coverings - Determination of mass per unit area of a reinforcement or a backing of polyvinyl chloride floor coverings |
| BS EN 719-1994 |
焊接堆層.任務和責任 |
Welding co-ordination - Tasks and responsibilities |
| BS EN 720-1-1999 |
可移動的儲氣瓶.氣體和氣體混合物.純?nèi)細馓匦?/td>
| Transportable gas cylinders - Gases and gas mixtures - Properties of pure gases |
| BS EN 720-2-1997 |
可移動的儲氣瓶.氣體和氣體混合物.氣體和氣體混合物的易燃性和氧化性測定 |
Transportable gas cylinders - Gases and gas mixtures - Determination of flammability and oxidizing ability of gases and gas mixtures |
| BS EN 721-1999 |
休閑住宿車輛.安全通風要求 |
Leisure accommodation vehicles - Safety ventilation requirements |
| BS EN 721-2005 |
休閑住宿車輛.安全通風要求 |
|
| BS EN 722-1-1996 |
旅居車.液體燃料供暖系統.第1部分:旅居掛車和活動房(游動的假日用房) |
(Leisure accommodation vehicles - Liquid fuel heating systems - Caravans and mobile homes (caravan holiday homes)) |
| BS EN 723-1996 |
鍛銅.管子表面碳測定的燃料法 |
Copper and copper alloys - Combustion method for determination of carbon on the inner surface of copper tubes or fittings |
| BS EN 724-1995 |
非放射性醫療器械用EN29001,EN46001,EN29002,EN46002標準的應用導則 |
Guidance on the application of EN 29001 and EN 46001 and of EN 29002 and EN 46002 for non-active medical devices |
| BS EN 725-1-1997 |
陶瓷先進技術.陶瓷粉的試驗方法.氧化鋁的純度測定 |
Advanced technical ceramics - Methods of test for ceramic powders - Determination of impurities in alumina |
| BS EN 725-10-1997 |
陶瓷先進技術.陶瓷粉的試驗方法.壓實密度的測定 |
Advanced technical ceramics - Methods of test for ceramic powders - Determination of compaction properties |
| BS EN 725-12-2001 |
高級工程陶瓷.陶瓷粉末的檢驗方法.氧化鋯的化學分析 |
Advanced technical ceramics - Methods of test for ceramic powders - Chemical analysis of zirconia |
| BS EN 725-3-1994 |
高級工業陶瓷.陶瓷粉未的試驗方法.第3部分:非氧化物氧含量的熱萃取法測定 |
Advanced technical ceramics - Methods of test for ceramic powders - Determination of the oxygen content of non-oxides by thermal extraction with a carrier gas |
| BS EN 725-5-1996 |
高技術陶瓷.陶瓷粉的試驗方法.第5部分:粒徑分布的測定 |
(Advanced technical ceramics - Methods of test for ceramic powders - Determination of the particle size distribution) |
| BS EN 725-6-1996 |
高級工業陶瓷.陶瓷粉末的試驗方法.表面積的測定 |
(Advanced technical ceramics - Methods of test for ceramic powders - Determination of the specific surface area) |
| BS EN 725-7-1996 |
高級工業陶瓷.陶瓷粉未的試驗方法.第3部分:非氧化物氧含量的熱萃取法測定 |
Advanced technical ceramics - Methods of test for ceramic powders - Determination of the absolute density |
| BS EN 725-8-1997 |
陶瓷先進技術.陶瓷粉的試驗方法.拍實大塊密度的測定 |
(Advanced technical ceramics - Methods of test for ceramic powders - Determination of tapped bulk density) |
| BS EN 725-9-1997 |
先進技術陶瓷.陶瓷粉末的試驗方法.未夯實的體密度的測定 |
(Advanced technical ceramics - Methods of test for ceramic powders - Determination of untamped bulk density) |
| BS EN 726-1-1995 |
識別卡系統.用于電訊的終端和芯片卡的要求.第1部分:系統概述 |
(Identification card systems - Telecommunications - Integrated circuit(s) cards and terminals - System overview) |
| BS EN 726-2-1996 |
識別卡系統.用于電訊的終端和芯片卡的要求.安全結構 |
(Identification card systems - Telecommunications - Integrated circuit(s) cards and terminals - Security framework) |
| BS EN 726-3-1996 |
識別卡系統.電信.集成電路卡和終端.應用獨立卡要求. |
(Identification card systems - Telecommunications - Integrated circuit(s) cards and terminals - Application independent card requirements) |
| BS EN 726-4-1995 |
識別卡系統.電訊.集成電路卡和終端.第4部分:獨立使用時的終端要求 |
(Identification card systems - Telecommunications - Integrated circuit(s) cards and terminals - Application independent card related terminal requirements) |
| BS EN 726-5-1999 |
識別卡系統.電信.集成電路卡和終端.支付方法 |
(Identification card systems - Telecommunications - Integrated circuit(s) cards and terminals - Payment methods) |
| BS EN 726-6-1996 |
識別卡系統.用于電訊的終端和芯片卡的要求.第6部分:通訊特性 |
(Identification card systems - Telecommunications - Integrated circuit(s) cards and terminals - Telecommunication features) |
| BS EN 726-7-1999 |
識別卡系統.通信.集成電路卡和終端.安全模塊 |
(Identification card systems - Telecommunications - Integrated circuit(s) cards and terminals - Security module) |
| BS EN 727-1995 |
塑料管道和管道系統.熱塑性塑料管和配件.維卡(vicat)軟化溫度的測定 |
Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST) |
| BS EN 728-1997 |
塑料管和管道系統.聚烯烴管和配件.氧化引導時間的測定 |
(Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time) |
| BS EN 729-1-1995 |
焊接質量要求.金屬材料熔焊.選擇和使用指南 |
(Quality requirements for welding - Fusion welding of metallic materials - Guidelines for selection and use) |
| BS EN 729-2-1995 |
焊接質量要求.金屬材料熔焊.綜合質量要求 |
(Quality requirements for welding - Fusion welding of metallic materials - Comprehensive quality requirements) |
| BS EN 729-3-1995 |
焊接質量要求.金屬材料熔焊.標準質量要求 |
Quality requirements for welding - Fusion welding of metallic materials - Standard quality requirements |
| BS EN 729-4-1995 |
焊接質量要求.金屬材料熔焊.基本質量要求 |
Quality requirements for welding - Fusion welding of metallic materials - Elementary quality requirements |
| BS EN 730-1-2002 |
氣焊設備的安全設施.混合物質燃燒(倒轉)制動器 |
Gas welding equipment - Safety devices - Incorporating a flame (flashback) arrestor |
| BS EN 730-2-2002 |
氣焊設備的安全設施.單項物質燃燒(倒轉)制動器 |
Gas welding equipment - Safety devices - Not incorporating a flame (flashback) arrestor |
| BS EN 731-1996 |
電焊裝置.送氣焊槍.規范和試驗 |
Gas welding equipment - Air-aspirated hand blowpipes - Specifications and tests |
| BS EN 732-1999 |
專用于液化石油氣的規范.吸收式制冷 |
(Specifications for dedicated liquefied petroleum gas appliances - Absorption refrigerators) |
| BS EN 733-1995 |
帶支承架的額定值為10bar的端吸式離心泵.公稱負荷點、主要尺寸和命名系統 |
End-suction centrifugal pumps, rating with 10 bar with bearing bracket - Nominal duty point, main dimensions, designation system |
| BS EN 734-1995 |
側槽泵PN40.公稱負荷點、主要尺寸和命名系統 |
(Side channel pumps PN 40 - Nominal duty point, main dimensions, designation system) |
| BS EN 735-1995 |
旋轉動態泵的總體尺寸.公差 |
(Overall dimensions of rotodynamic pumps - Tolerances) |
| BS EN 736-1-1995 |
閥門.術語.閥門類型定義 |
(Valves - Terminology - Definition of types of valves) |
| BS EN 736-2-1997 |
閥門.術語.閥門組件定義 |
(Valves - Terminology - Definition of components of valves) |
| BS EN 736-3-1999 |
閥門.術語.術語定義 |
(Valves - Terminology - Definition of terms) |
| BS EN 737-1-1998 |
醫療氣體管道系統.壓縮醫療氣體用終端設備和真空終端設備 |
(Medical gas pipeline systems - Terminal units for compressed medical gases and vacuum) |
| BS EN 737-2-1998 |
醫療氣體管道系統.麻醉氣體凈化處理系統.基本要求 |
(Medical gas pipeline systems - Anaesthetic gas scavenging disposal systems - Basic requirements) |
| BS EN 737-3-2000 |
醫療氣體管道系統.壓縮醫療氣體和真空用管道 |
(Medical gas pipeline systems - Pipelines for compressed medical gases and vacuum) |
| BS EN 737-4-1998 |
醫療氣體管道系統.麻醉氣體凈化系統的終端設備 |
(Medical gas pipeline systems - Terminal units for anaesthetic gas scavenging systems) |
| BS EN 738-1-1997 |
醫用氣體用壓力調節器.壓力調節器和有流量計裝置的壓力調節器 |
(Pressure regulators for use with medical gases - Pressure regulators and pressure regulators with flow metering devices) |
| BS EN 738-2-1999 |
醫用氣體用壓力調節器.進氣壓力調節器和輸送管道壓力調節器 |
(Pressure regulators for use with medical gases - Manifold and line pressure regulators) |
| BS EN 738-3-1999 |
醫用氣體用壓力調節器.帶氣瓶閥的完整壓力調節器 |
(Pressure regulators for use with medical gases - Pressure regulators integrated with cylinder valves) |
| BS EN 738-4-1999 |
醫用氣體用壓力調節器.醫療設備用低壓壓力調節器 |
(Pressure regulators for use with medical gases - Low-pressure regulators intended for incorporation into medical equipment) |
| BS EN 739-1998 |
醫療氣體設備用低壓軟管組件 |
(Low-pressure hose assemblies for use with medical gases) |
| BS EN 740-1999 |
麻醉工作站及其工作艙.特殊要求 |
(Anaesthetic workstations and their modules - Particular requirements) |
| BS EN 741-2000 |
連續處理設備和系統.散裝材料氣動處理用系統和件的安全要求 |
(Continuous handling equipment and systems - Safety requirements for systems and their components for pneumatic handling of bulk materials) |
| BS EN 743-1995 |
塑料管道和導管系統.熱塑管.縱向復原的測定 |
(Plastics piping and ducting systems - Thermoplastics pipes - Determination of the longitudinal reversion) |
| BS EN 744-1996 |
塑料管道和導管系統.熱塑管.耐連續吹風的試驗方法 |
(Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method) |
| BS EN 745-1999 |
農業機械.旋轉式割草機和甩刀式割草機 |
(Agricultural machinery - Rotary mowers and flail-mowers - Safety) |
| BS EN 746-1-1997 |
工業熱處理設備.工業熱處理設備常規安全要求 |
(Industrial thermoprocessing equipment - Common safety requirements for industrial thermoprocessing equipment) |
| BS EN 746-2-1997 |
工業熱處理設備.第2部分:燃燒和燃料處理系統的安全要求 |
(Industrial thermoprocessing equipment - Safety requirements for combustion and fuel handling systems) |
| BS EN 746-3-1997 |
工業熱加工設備.環境氣體產生和使用的安全要求 |
(Industrial thermoprocessing equipment - Safety requirements for the generation and use of atmosphere gases) |
| BS EN 746-4-2000 |
工業熱處理設備.熱浸電鍍熱處理設備的特殊安全要求 |
(Industrial thermoprocessing equipment - Particular safety requirements for hot dip galvanizing thermoprocessing equipment) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com