標準號 |
中文名稱 |
英文名稱 |
| EN ISO 2871-2-1994 |
表面活性劑洗滌劑陽離子活性物含量的測定第2部分：低分子質量(200～500)陽離子活性物 |
Surface active agents - Detergents - Determination of cationic-active matter content - Part 2: Cationic-active matter of low molecular mass (between 200 and 500) (ISO 2871-2-1990) |
| EN ISO 2873-2002 |
包裝 滿裝運輸包裝和單件貨物 低壓試驗 |
Packaging - Complete, filled transport packages and unit loads - Low pressure test (ISO 2873:2000) |
| EN ISO 2875-2002 |
包裝 滿裝運輸包裝和單件貨物 噴水試驗 |
Packaging - Complete, filled transport packages and unit loads - Water-spray test (ISO 2875:2000) |
| EN ISO 2897-1-1999 |
塑料耐沖擊聚苯乙烯(PS-I)模塑和擠塑材料第1部分：命名系統和基本規范 |
Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2897-1:1997) |
| EN ISO 2897-2-1999 |
塑料耐沖擊聚苯乙烯(PS-I)模塑和擠塑材料第2部分：試樣的制備和性能的測定 |
Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2897-2:1994, including Technical Corrigendum 1:1995) |
| EN ISO 2898-1-1999 |
塑料增塑聚氯乙烯(PVC-P)模塑和擠塑材料第1部分：命名系統和基本規范 |
Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2898-1:1996) |
| EN ISO 2898-2-1999 |
塑料增塑聚氯乙烯(PVC-P)模塑和擠塑材料第2部分：試樣的制備和性能的測定 |
Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2898-2:1997) |
| EN ISO 291-1997 |
塑料狀態調節和試驗用標準大氣壓 |
Plastics - Standard atmospheres for conditioning and testing (ISO 291:1997) |
| EN ISO 2922-2000 |
聲學內河水道上和港口中的船舶輻射的空氣聲的測量 |
Acoustics - Measurement of airborne sound emitted by vessels on inland waterways and harbours (ISO 2922:2000) |
| EN ISO 293-2003 |
塑料熱塑性材料的壓模塑試樣 |
Plastics - Compression moulding test specimens of thermoplastic materials (ISO 293:1986) |
| EN ISO 294-2-1998 |
塑料熱塑性材料試樣的注模塑法第2部分：小拉伸棒 |
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars (ISO 294-2:1996) |
| EN ISO 294-3-2003 |
塑料熱塑性材料試樣的注模塑法第3部分：小板 |
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2002) |
| EN ISO 294-4-2003 |
塑料熱塑性材料試樣的注模塑法第4部分：模塑收縮率的測定 |
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4: Determination of moulding shrinkage (ISO 294-4:2001) |
| EN ISO 295-1998 |
塑料熱固性材料試樣的壓模塑法 |
Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:1991) |
| EN ISO 295-2004 |
塑料.熱固性材料試樣的壓模塑法 |
|
| EN ISO 3001-1999 |
塑料環氧化合物環氧基當量的測定 |
Plastics - Epoxy compounds - Determination of epoxy equivalent (ISO 3001:1999) |
| EN ISO 3037-1996 |
瓦楞紙板邊緣抗碾性的測定(邊緣未浸臘法) |
Corrugated fibreboard - Determination of edgewise crush resistance (Unwaxed edge method) (ISO 3037:1994) |
| EN ISO 305-1999 |
塑料聚氯乙烯和有關均聚合物和共聚物及其混合物的熱穩定性的測定色變法 |
Plastics - Determination of thermal stability of poly(vinyl chloride), related chlorine - Containing homopolymers and copolymers and their compounds - Discoloration method (ISO 305:1990) |
| EN ISO 3059-2001 |
無損檢測滲透檢驗與磁性粒子檢驗檢視條件 |
Non-destructive testing - Penetrant testing and magnetic particle testing - Viewing conditions (ISO 3059:2001) |
| EN ISO 306-1996 |
塑料熱塑性材料維卡軟化溫度的測定 |
Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:1994) |
| EN ISO 306-2004 |
塑料.熱塑性材料.維卡特(VICAT)軟化溫度的測定(VST) |
|
| EN ISO 307-2003 |
塑料聚酰胺粘度值的測定 |
Plastics - Polyamides - Determination of viscosity number (ISO 307:2003) |
| EN ISO 308-1997 |
塑料酚醛模塑材料丙酮可溶性物質(在未模塑狀態時表現樹脂含量)的測定 |
Plastics - Phenolic moulding materials - Determination of acetone-soluble matter (apparent resin content of material in the unmoulded state) (ISO 308:1994) |
| EN ISO 3098-0-1997 |
技術產品文件文字第0部分：一般要求 |
Technical product documentation - Lettering - Part 0: General requirements (ISO 3098-0:1997) |
| EN ISO 3098-2-2000 |
技術產品文件文字第2部分：拉丁字母表、數字和符號 |
Technical product documentation - Lettering - Part 2: Latin alphabet, numeral and marks (ISO 3098-2:2000) |
| EN ISO 3098-3-2000 |
技術產品文件文字第3部分：希臘字母表 |
Technical product documentation - Lettering - Part 3: Greek alphabet (ISO 3098-3:2000) |
| EN ISO 3098-4-2000 |
技術產品文件文字第4部分：拉丁字母表用的區分標記和特殊標記 |
Technical product documentation - Lettering - Part 4: Diacritical and particular marks for the Latin alphabet (ISO 3098-4:2000) |
| EN ISO 3098-5-1997 |
技術產品文件文字第5部分：拉丁字母，數字和標志的CAD文字分類法 |
Technical product documentation - Lettering - Part 5: CAD lettering of the Latin alphabet, numerals and marks (ISO 3098-5:1997) |
| EN ISO 3098-6-2000 |
技術產品文件文字第6部分：西里爾字母表 |
Technical product documentation - Lettering - Part 6: Cyrillic alphabet (ISO 3098-6:2000) |
| EN ISO 3104-1996 |
石油產品透明和不透明石油液體運動粘度的測定和動力粘度的計算 |
Petroleum products - Transparent and opaque liquids - Determination of kinematic viscosity and calculation of dynamic viscosity (ISO 3104:1994) |
| EN ISO 3107-2004 |
牙醫學.鋅氧化物/丁香酸和鋅氧化物/非丁香酸粘固粉 |
|
| EN ISO 3164-1999 |
土方機械保護結構的實驗室鑒定撓曲極限的規范 |
Earth-moving machinery - Laboratory evaluations of protective structures - Specifications for deflection-limiting volume (ISO 3164:1995) |
| EN ISO 3166-1-1997 |
國家和他們的地區名的代碼第1部分：國家代碼 |
Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:1997) |
| EN ISO 3167-2003 |
塑料多用途試驗用試樣 |
Plastics - Multipurpose test specimens (ISO 3167:2002) |
| EN ISO 3170-1998 |
石油液體人工采樣 |
Petroleum liquids - Manual sampling (ISO 3170:1988, including Amendment 1:1998) |
| EN ISO 3170-2004 |
石油液體.人工采樣 |
|
| EN ISO 3171-1999 |
石油液體自動管線的采樣 |
Petroleum liquids - Automatic pipeline sampling (ISO 3171:1988) |
| EN ISO 3175-1-1998 |
紡織品干洗和整理第1部分：紡織品和服裝可洗凈性評估方法 |
Textiles - Dry-cleaning and finishing - Part 1: Method for assessing the cleanability of textiles and garments (ISO 3175-1:1998) |
| EN ISO 3175-2-1998 |
紡織品干洗和整理第2部分：四氯乙烯程序 |
Textiles - Dry-cleaning and finishing - Part 2: Procedures for tetrachloroethene (ISO 3175-2:1998) |
| EN ISO 3175-3-2003 |
紡織品機械干洗穩定性的評估 第3部分：用烴溶劑清洗和整理時試驗性能的程序 |
Textiles - Professional care, drycleaning and wetcleaning of fabrics and garments - Part 3: Procedure for testing performance when cleaning and finishing using in hydrocarbon solvents (ISO 3175-3:2003) |
| EN ISO 3175-4-2003 |
紡織品織物和衣服的專業護理、干洗和濕洗 用模擬濕洗洗滌和整理時性能試驗的程序 |
Textiles - Professional care, drycleaning and wetcleaning of fabrics and garments - Part 4: Procedure for testing performance when cleaning and finishing using simulated wetcleaning (ISO 3175-4:2003) |
| EN ISO 3188-1994 |
淀粉和淀粉制品用凱氏法測定氮含量滴定法 |
Starches and derived products - Determination of nitrogen content by the Kjeldahl method - Titrimetric method (ISO 3188:1978) |
| EN ISO 3219-1994 |
塑料液態或乳態或分散狀的聚合物/樹脂使用規定剪切率的旋轉式粘度計測定粘度 |
Plastics - Polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate (ISO 3219:1993) |
| EN ISO 3231-1997 |
色漆和清漆耐二氧化硫濕空氣作用的測定 |
Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993) |
| EN ISO 3248-2000 |
色漆和清漆熱效應的測定 |
Paints and varnishes - Determination of the effect of heat (ISO 3248:1998) |
| EN ISO 3251-2003 |
色漆、清漆和色漆 非揮發物含量的測定 |
Paints, varnishes and plastics - Determination of non-volatile matter content (ISO 3251:2003) |
| EN ISO 3252-2000 |
粉末冶金術語 |
Powder metallurgy - Vocabulary (ISO 3252:1999) |
| EN ISO 3262-1-1998 |
涂料用填充劑規范和測試方法第1部分：導言和通用試驗方法 |
Extenders for paints - Specifications and methods of test - Part 1: Introduction and general test methods (ISO 3262-1:1997) |
| EN ISO 3262-10-2000 |
涂料用填充劑規范和測試方法第10部分：片狀天然滑石 /亞氯酸鹽 |
Extenders for paints - Specifications and methods of test - Part 10: Natural, talc/chlorite in lamellar form (ISO 3262-10:2000) |
| EN ISO 3262-11-2000 |
涂料用填充劑規范和測試方法第11部分：含碳酸鹽的片狀天然滑石 |
Extenders for paints - Specifications and methods of test - Part 11: Natural talc, in lamellar form, containing carbonates (ISO 3262-11:2000) |
| EN ISO 3262-12-2001 |
涂料用填充劑規范和測試方法第12部分：白云母 |
Extenders for paints - Specifications and methods of test - Part 12: Muscovite-type mica (ISO 3262-12:2001) |
| EN ISO 3262-13-1998 |
涂料用填充劑規范和測試方法第13部分：天然石英(礦物) |
Extenders for paints - Specifications and methods of test - Part 13: Natural quartz (ground) (ISO 3262-13:1997) |
| EN ISO 3262-14-2000 |
涂料用填充劑規范和測試方法第14部分：白硅石 |
Extenders for paints - Specifications and methods of test - Part 14: Cristobalite (ISO 3262-14:2000) |
| EN ISO 3262-15-2000 |
涂料用填充劑規范和測試方法第15部分：透明石英 |
Extenders for paints - Specifications and methods of test - Part 15: Vitreous silica (ISO 3262-15:2000) |
| EN ISO 3262-16-2000 |
涂料用填充劑規范和測試方法第16部分：氫氧化鋁 |
Extenders for paints - Specifications and methods of test - Part 16: Aluminium hydroxides (ISO 3262-16:2000) |
| EN ISO 3262-17-2000 |
涂料用填充劑規范和測試方法第17部分：沉淀硅酸鈣 |
Extenders for paints - Specifications and methods of test - Part 17: Precipitated calcium silicate (ISO 3262-17:2000) |
| EN ISO 3262-18-2000 |
涂料用填充劑規范和測試方法第18部分：沉淀硅鋁酸鈉 |
Extenders for paints - Specifications and methods of test - Part 18: Precipitated sodium aluminium silicate (ISO 3262-18:2000) |
| EN ISO 3262-19-2000 |
涂料用填充劑規范和測試方法第19部分：沉淀二氧化硅(石英) |
Extenders for paints - Specifications and methods of test - Part 19: Precipitated silica (ISO 3262-19:2000) |
| EN ISO 3262-2-1998 |
涂料用填充劑規范和測試方法第2部分：重晶石(天然硫酸鋇) |
Extenders for paints - Specifications and methods of test - Part 2: Baryte (natural barium sulfate) (ISO 3262-2:1998) |
| EN ISO 3262-20-2000 |
涂料用填充劑規范和測試方法第20部分：噴霧二氧化硅(石英) |
Extenders for paints - Specifications and methods of test - Part 20: Fumed silica (ISO 3262-20:2000) |
| EN ISO 3262-21-2000 |
涂料用填充劑規范和測試方法第21部分：石英沙(礦物天然石英) |
Extenders for paints - Specifications and methods of test - Part 21: Silica sand (unground natural quartz) (ISO 3262-21:2000) |
| EN ISO 3262-22-2001 |
涂料用填充劑規范和測試方法第22部分：熱堿處理的硅藻土 |
Extenders for paints - Specifications and methods of test - Part 22: Flux-calcined kieselguhr (ISO 3262-22:2001) |
| EN ISO 3262-3-1998 |
涂料用填充劑規范和測試方法第3部分：沉淀硫酸鋇 |
Extenders for paints - Specifications and methods of test - Part 3: Blanc fixe (ISO 3262-3:1998) |
| EN ISO 3262-4-1998 |
涂料用填充劑規范和測試方法第4部分：白堊 |
Extenders for paints - Specifications and methods of test - Part 4: Whiting (ISO 3262-4:1998) |
| EN ISO 3262-5-1998 |
涂料用填充劑規范和測試方法第5部分：天然結晶硫酸鈣 |
Extenders for paints - Specifications and methods of test - Part 5: Natural crystalline calcium carbonate (ISO 3262-5:1998) |
| EN ISO 3262-6-1998 |
涂料用填充劑規范和測試方法第6部分：沉淀碳酸鈣 |
Extenders for paints - Specifications and methods of test - Part 6: Precipitated calcium carbonate (ISO 3262-6:1998) |
| EN ISO 3262-7-1998 |
涂料用填充劑規范和測試方法第7部分：白云石 |
Extenders for paints - Specifications and methods of test - Part 7: Dolomite (ISO 3262-7:1998) |
| EN ISO 3262-8-1999 |
涂料用填充劑規范和測試方法第8部分：天然粘土 |
Extenders for paints - Specifications and methods of test - Part 8: Natural clay (ISO 3262-8:1999) |
| EN ISO 3262-9-1998 |
涂料用填充劑規范和測試方法第9部分：煅燒粘土 |
Extenders for paints - Specifications and methods of test - Part 9: Calcined clay (ISO 3262-9:1997) |
| EN ISO 3269-2000 |
緊固件驗收檢查 |
Fasteners - Acceptance inspection (ISO 3269:2000) |
| EN ISO 3274-1997 |
產品幾何量技術規范(GPS)表面結構：輪廓法接觸(觸針)式儀器的標稱特性 |
Geometrical Product Specifications (GPS) - Surface texture: Profile method - Nominal characteristics of contact (stylus) instruments (ISO 3274:1996) |
| EN ISO 3325-1999 |
煅結金屬材料，不包括硬質金屬橫向斷裂強度的測定 |
Sintered metal materials, excluding hardmetals - Determination of transverse rupture strength (ISO 3325:1996) |
| EN ISO 3336-1996 |
牙科學合成聚合物牙齒 |
Dentistry - Synthetic polymer teeth (ISO 3336:1993) |
| EN ISO 3344-1997 |
增強制品含濕量的測定 |
Reinforcement products - Determination of moisture content (ISO 3344:1997) |
| EN ISO 3376-2002 |
皮革物理與機械性試驗抗拉強度與伸長率的測定 |
Leather - Physical and mechanical tests - Determination of tensile strength and percentage extension (ISO 3376:2002) |
| EN ISO 3377-1-2002 |
皮革物理與機械性試驗撕裂力的測定第1部分：單邊撕裂 |
Leather - Physical and mechanical tests; Determination of tear load - Part 1: Single edge tear (ISO 3377-1:2002) |
| EN ISO 3377-2-2002 |
皮革物理與機械性試驗撕裂力的測定第2部分：雙向邊緣撕裂 |
Leather - Physical and mechanical tests; Determination of tear load - Part 2: Double edge tear (ISO 3377-2:2002) |
| EN ISO 3378-2002 |
皮革物理與機械性試驗?zāi)土Ｃ媪鸭y和耐粒面裂紋指數的測定 |
Leather - Physical and mechanical tests - Determination of resistance to grain cracking and grain crack index (ISO 3378:2002) |
| EN ISO 3380-2002 |
皮革物理與機械性試驗收縮溫度的測定 |
Leather - Physical and mechanical tests - Determination of shrinkage temperature (ISO 3380:2002) |
| EN ISO 3382-2000 |
聲學根據其他聲學參數測量房間混向時間 |
Acoustics - Measurement of the reverberation time of rooms with reference to other acoustical parameters (ISO 3382:1997) |
| EN ISO 3385-1995 |
軟質泡沫聚合材料用恒定載荷沖擊測定疲勞性能 |
Flexible cellular polymeric materials - Determination of fatigue constant-load pounding (ISO 3385:1989) |
| EN ISO 3386-1-1997 |
軟質泡沫聚合材料壓縮應力應變特性的測定第1部分：低密度材料 |
Polymeric materials, cellular flexible - Determination of stress-strain characteristic in compression - Part 1: Low-density materials (ISO 3386-1:1986) |
| EN ISO 3386-2-1998 |
軟質泡沫聚合材料壓縮應力應變特性的測定第2部分：高密度材料 |
Flexible cellular polymeric materials - Determination of stress-strain characteristics in compression - Part 2: High-density materials (ISO 3386-2:1997) |
| EN ISO 3405-2000 |
石油產品常壓下餾份特性的測定 |
Petroleum products - Determination of distillation characteristics at atmospheric pressure (ISO 3405:2000) |
| EN ISO 3411-1999 |
土方機械司機的身體尺寸與司機的最小活動空間 |
Earth-moving machinery - Human physical dimensions of operators and minimum operator space envelope (ISO 3411:1995) |
| EN ISO 3450-1996 |
土方機械輪胎式機械的制動系統系統和性能的要求及試驗方法 |
Earth-moving machinery - Braking systems of rubber-tyred machines - Systems and performance requirements and test procedures (ISO 3450:1996) |
| EN ISO 3451-1-1997 |
塑料灰分的測定第1部分：一般方法 |
Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:1997) |
| EN ISO 3451-4-2000 |
塑料灰分的測定第4部分：聚酰胺 |
Plastics - Determination of ash - Part 4: Polyamides (ISO 3451-4:1998) |
| EN ISO 3451-5-2002 |
塑料灰份的測定第5部分：聚氯乙烯 |
Plastics - Determination of ash - Part 5: Poly(vinyl chloride) (ISO 3451-5:2002) |
| EN ISO 3452-2-2000 |
無損探傷滲透性探傷檢驗第2部分：滲透材料的測定 |
Non-destructive testing - Penetrant testing - Part 2: Testing of penetrant materials (ISO 3452-2:2000) |
| EN ISO 3452-4-1998 |
無損探傷滲透性探傷檢驗第4部分：設備 |
Non-destructive testing - Penetrant testing - Part 4: Equipment (ISO 3452-4:1998) |
| EN ISO 3457-2003 |
土方機械擋板定義和要求 |
Earth-moving machinery - Guards - Definitions and requirements (ISO 3457:2003) |
| EN ISO 3497-2000 |
金屬覆蓋層鍍層的厚度測量X射線光譜法 |
Metallic coatings - Measurement of coating thickness - X-ray spectrometric methods (ISO 3497:2000) |
| EN ISO 3506-1-1997 |
耐腐蝕不銹鋼緊固件的機械性能第1部分：螺栓、螺釘和螺柱 |
Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:1997) |
| EN ISO 3506-2-1997 |
耐腐蝕不銹鋼緊固件的機械性能第2部分：螺母 |
Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 2: Nuts (ISO 3506-2:1997) |
| EN ISO 3506-3-1997 |
耐腐蝕不銹鋼緊固件的機械性能第3部分：緊定螺釘及類似的不受應力的螺紋緊固件 |
Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:1997) |
| EN ISO 3506-4-2003 |
耐腐蝕不銹鋼緊固件的機械性能第4部分：自攻螺釘 |
Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 4: Tapping screws (ISO 3506-4:2003) |
| EN ISO 3521-1999 |
塑料不飽和聚酯和環氧樹脂總體積收縮率的測定 |
Plastics - Unsaturated polyester and epoxy resins - Determination of overall volume shrinkage (ISO 3521:1997) |
| EN ISO 354-2003 |
聲學 混響室中聲吸收的測量 |
Acoustics - Measurement of sound absorption in a reverberation room (ISO 354:2003) |
| EN ISO 3543-2000 |
金屬和非金屬覆蓋層厚度的測量β射線背散射法 |
Metallic and non-metallic coatings - Measurement of thickness - Beta backscatter method (ISO 3543:2000) |
| EN ISO 3549-2002 |
色漆用鋅粉顏料規范和試驗方法 |
Zinc dust pigments for paints - Specifications and test methods (ISO 3549:1995) |
| EN ISO 3582-2000 |
軟質泡沫聚合材料小試樣對小火焰水平方向燃燒特性的實驗室評估 |
Flexible cellular polymeric materials - Laboratory assessment of horizontal burning characteristics of small specimens subjected to a small flame (ISO 3582:2000) |
| EN ISO 3593-1994 |
淀粉灰分的測定 |
Starch - Determination of ash (ISO 3593:1981) |
| EN ISO 3596-2001 |
動植物油脂不皂化的測定乙醚提取法 |
Animal and vegetable fats and oils - Determination of unsaponifiable matter - Method using diethyl ether extraction (ISO 3596:2000) |
| EN ISO 3613-2001 |
鋅、鎘、鋁鋅合金和鋅鋁合金的鉻酸鹽轉化膜試驗方法 |
Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys - Test methods (ISO 3613:2000) |
| EN ISO 3630-1-1994 |
牙根管器械第1部分：推管銼、擴大器、倒刺拔髓針、粗銼、糊劑輸送器、探針及棉捻 |
Dental root-canal instruments - Part 1: Files, reamers, barbed broaches, rasps, paste carriers, explorers and cotton broaches (ISO 3630-1:1992) |
| EN ISO 3630-2-2000 |
牙根管器械第2部分：擴大器 |
Dental root-canal instruments - Part 2: Enlargers (ISO 3630-2:2000) |
| EN ISO 3630-3-1996 |
牙根管器械第3部分：聚光鏡、充填器和攤開器 |
Dental root-canal instruments - Part 3: Condensers, pluggers and spreaders (ISO 3630-3:1994) |
| EN ISO 3650-1998 |
產品幾何技術規范(GPS)長度標準塊規 |
Geometrical Product Specifications (GPS) - Length standards - Gauge blocks (ISO 3650:1998) |
| EN ISO 3651-1-1998 |
不銹鋼耐晶間腐蝕的測定第1部分：奧氏體和鐵素奧氏體(二重)不銹鋼用失重測定法在硝酸介質中的腐蝕試驗( |
Determination of resistance to intergranular corrosion of stainless steels - Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels - Corrosion test in nitric acid medium by measurement of loss in mass (Huey test) (ISO 3651-1:1998) |
| EN ISO 3651-2-1998 |
不銹鋼耐晶間腐蝕的測定第2部分：奧氏體、奧氏體和鐵素奧氏體(二重)不銹鋼在硫酸介質中的腐蝕試驗 |
Determination of resistance to intergranular corrosion of stainless steels - Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels - Corrosion test in media containing sulfuric acid (ISO 3651-2:1998) |
| EN ISO 3656-2002 |
動植物脂肪和油表示為特殊UV消失的紫外線吸收率的測定 |
Animal and vegetable fats and oils - Determination of ultraviolet absorbance expressed as specific UV extinction (ISO 3656:2002) |
| EN ISO 3657-2003 |
動植物脂肪和油脂 皂化值的測定 |
Animal and vegetable fats and oils - Determination of saponification value (ISO 3657:2002) |
| EN ISO 3668-2001 |
色漆和清漆色漆顏色的目視比色 |
Paints and varnishes - Visual comparison of the colour of paints (ISO 3668:1998) |
| EN ISO 3671-1998 |
塑料氨基模塑材料揮發性物質的測定 |
Plastics - Aminoplastic moulding materials - Determination of volatile matter (ISO 3671:1976) |
| EN ISO 3672-1-2001 |
塑料不飽和聚酯樹脂第1部分：命名體系 |
Plastics - Unsaturated-polyester resins (UP-R) - Part 1: Designation system (ISO 3672-1:2000) |
| EN ISO 3672-2-2001 |
塑料不飽和聚酯樹脂第2部分：試樣的制備和特性的測定 |
Plastics - Unsaturated-polyester resins (UP-R) - Part 2: Preparation of test specimens and determination of properties (ISO 3672-2:2000) |
| EN ISO 3673-1-1999 |
塑料環氧樹脂第1部分：命名 |
Plastics - Epoxy resins - Part 1 : Designation (ISO 3673-1:1996) |
| EN ISO 3673-2-1999 |
塑料環氧樹脂第2部分：試樣的制備和特性的測定 |
Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties (ISO 3673-2:1999) |
| EN ISO 3675-1998 |
原油和液體石油產品密度實驗室測定密度計法 |
Crude petroleum and liquid petroleum products - Laboratory determination of density - Hydrometer method (ISO 3675:1998) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com