標準號 |
中文名稱 |
英文名稱 |
| EN ISO 10707-1997 |
水質用生化需氧量分析法評估水介質中有機化合物的最大需氧生物降解能力(封瓶試驗) |
Water quality - Evaluation in an aqueous medium of the ultimate aerobic biodegradability of organic compounds - Method by analysis of biochemical oxygen demand (closed bottle test) (ISO 10707:1994) |
| EN ISO 1071-2003 |
焊接消耗品鑄鐵熔焊用藥劑焊極、焊絲、焊條和管關芯焊極分類 |
Welding consumables - Covered electrodes, wires, rods and tubular cored electrodes for fusion welding of cast iron - Classification (ISO 1071:2003) |
| EN ISO 10712-1995 |
水質假單胞桿菌類生長抑制性試驗(假單胞菌類細胞增殖抑制試驗) |
Water quality - Pseudomonas putida growth inhibition test (Pseudomonas cell multiplication inhibition test) (ISO 10712:1995) |
| EN ISO 10714-2002 |
鋼和鐵磷含量的測定磷釩鉬酸鹽分光光度法 |
Steel and iron - Determination of phosphorus content - Phosphovanadomolybdate spectrophotometric method (ISO 10714:1992) |
| EN ISO 10715-2000 |
天然氣取樣指南 |
Natural gas - Sampling guidelines (ISO 10715:1997) |
| EN ISO 10723-2002 |
天然氣在線分析系統的性能評定 |
Natural gas - Performance evaluation for on-line analytical systems (ISO 10723:1995) |
| EN ISO 10724-1-2001 |
塑料熱固性粉末模塑復合物試樣的注射模塑成型第1部分：一般原則和多用途試樣的模塑成型 |
Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of multipurpose test specimens (ISO 10724-1:1998) |
| EN ISO 10724-2-2000 |
塑料熱固性粉末模塑復合物試樣的注射模塑成型第2部分：小板材 |
Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 2: Small plates (ISO 10724-2:1998) |
| EN ISO 10807-1996 |
管道工程在爆燃性空氣中電纜保護用皺紋軟金屬管組件 |
Pipework - Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmosphere (ISO 10807:1994) |
| EN ISO 10819-1996 |
機械振動與沖擊手臂振動手掌戴手套時對振動傳遞率的測量和評定方法 |
Mechanical vibration and shock - Hand-arm vibration - Method for the measurement and evaluation of the vibration transmissibility of gloves at the palm of the hand (ISO 10819:1996) |
| EN ISO 10846-1-1998 |
聲學和振動彈性件的振動聲傳輸特性的實驗室測量第1部分：原理和指南 |
Acoustics and vibration - Laboratory measurement of vibro-acoustic transfer properties of resilient elements - Part 1: Principles and guidelines (ISO 10846-1:1997) |
| EN ISO 10846-2-1998 |
聲學和振動彈性件的振動聲傳輸特性的實驗室測量第2部分：傳輸運動用彈性支撐的動態勁度直接法 |
Acoustics and vibration - Laboratory measurement of vibro-acoustic transfer properties of resilient elements - Part 2: Dynamic stiffness of elastic supports for translatory motion - Direct method (ISO 10846-2:1997) |
| EN ISO 10846-3-2002 |
聲學和振動彈性件的振動聲傳輸特性的實驗室測量第3部分：平移用彈性支架的動態勁度測定用間接法 |
Acoustics and vibration - Laboratory measurements of vibro-acoustic transfer properties of resilient elements - Part 3: Indirect method for determination of the dynamic stiffness of resilient supports for translatory motion (ISO 10846-3:2002) |
| EN ISO 10846-4-2003 |
聲學和振動彈性件的振動聲傳輸特性的實驗室測量第4部分：除平移用彈性支架之外的件的動態勁度 |
Acoustics and vibration - Laboratory measurement of vibro-acoustic transfer properties of resilient elements - Part 4: Dynamic stiffness of elements other than resilient supports for translatory motion (ISO 10846-4:2003) |
| EN ISO 10882-1-2001 |
焊接和相關工藝的衛生與安全工作人員呼吸區域中空氣中懸浮顆粒物及氣體的取樣第1部分：空氣中粒子取樣 |
Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operators breathing zone - Part 1: Sampling of airborne particles (ISO 10882-1:2001) |
| EN ISO 10882-2-2000 |
焊接和相關工藝的衛生與安全工作人員呼吸區域中空氣中懸浮顆粒物及氣體的取樣第2部分：氣體取樣 |
Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operatiors breathing zone - Part 2: Sampling of gases (ISO 10882-2:2000) |
| EN ISO 10938-1998 |
眼科儀器圖片投影儀 |
Ophthalmic instruments - Chart projectors (ISO 10938:1998) |
| EN ISO 10940-1998 |
眼科儀器眼底照相機 |
Ophthalmic instruments - Fundus cameras (ISO 10940:1998) |
| EN ISO 10943-1998 |
眼科儀器間接檢眼鏡 |
Ophthalmic instruments - Indirect ophthalmoscopes (ISO 10943:1998) |
| EN ISO 10944-1998 |
眼科儀器斜視診療器 |
Ophthalmic instruments - Synoptophores (ISO 10944:1998) |
| EN ISO 10960-1996 |
橡膠和塑料軟管動態條件下耐臭氧性的評定 |
Rubber and plastics hoses - Assessment of ozone resistance under dynamic conditions (ISO 10960:1994) |
| EN ISO 10964-1997 |
粘合劑螺紋緊固件上厭氧粘合劑的抗扭強度的測定 |
Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993) |
| EN ISO 10993-1-2003 |
醫療器械的生物學評價第1部分：評價與試驗 |
Biological evaluation of medical devices - Part 1: Evaluation and testing (ISO 10993-1:2003) |
| EN ISO 10993-10-2002 |
醫療器械的生物學評價第10部分：刺激與致敏試驗 |
Biological evaluation of medical devices - Part 10: Tests for irritation and delayed-type hypersensitivity (ISO 10993-10:2002) |
| EN ISO 10993-11-1995 |
醫療器械的生物學評價第11部分：全身毒性試驗 |
Biological evaluation of medical devices - Part 11: Tests for systemic toxicity (ISO 10993-11:1993) |
| EN ISO 10993-12-1996 |
醫療器械的生物學評價第12部分：樣品制備和參照物 |
Biological evaluation of medical devices - Part 12: Sample preparation and reference materials (ISO 10993-12:1996) |
| EN ISO 10993-13-1998 |
醫療器械的生物學評價第13部分：聚合物醫療器械降解產物的定性與定量 |
Biological evaluation of medical devices - Part 13: Identification and quantification of degradation products from polymeric medical devices (ISO 10993-13:1998) |
| EN ISO 10993-14-2001 |
醫療器械的生物學評價第14部分：陶瓷降解產物的識別與合格鑒定 |
Biological evaluation of medical devices - Part 14: Identification and quantification of degradation products from ceramics (ISO 10993-14:2001) |
| EN ISO 10993-15-2000 |
醫療器械的生物學評價第15部分：金屬與合金降解產物的識別與定性 |
Biological evaluation of medical devices - Part 15: Identification and quantification of degradation products from metals and alloys (ISO 10993-15:2000) |
| EN ISO 10993-16-1997 |
醫療器械的生物學評價第16部分：降解產物與可容出物的毒物動力學研究設計 |
Biological evaluation of medical devices - Part 16: Toxickinetic study design for degradation products and leachables (ISO 10993-16:1997) |
| EN ISO 10993-17-2002 |
醫療器械的生物學評價第17部分：可濾物質允許權限的評定 |
Biological evaluation of medical devices - Part 17: Establishment of allowable limits for leachable substances (ISO 10993-17:2002) |
| EN ISO 10993-2-1998 |
醫療器械的生物學評價第2部分：動物保護要求 |
Biological evaluation of medical devices - Part 2: Animal welfare requirements (ISO 10993-2:1992) |
| EN ISO 10993-4-2002 |
醫療器械的生物學評價 第4部分:與血液相互作用的試驗選擇 |
Biological evaluation of medical devices - Part 4: Selection of tests for interactions with blood (ISO 10993-4:2002) |
| EN ISO 10993-5-1999 |
醫療器械的生物學評價第5部分：體外細胞毒性試驗 |
Biological evaluation of medical devices - Part 5: Tests for in vitro cytotoxicity (ISO 10993-5:1999) |
| EN ISO 10993-7-1995 |
醫療器械的生物學評價第7部分：環氧乙烷滅菌殘留量 |
Biological evaluation of medical devices - Part 7: Ethylene oxide sterilization residuals (ISO 10993-7:1995) |
| EN ISO 10993-8-2000 |
醫療器械的生物學評價第8部分：生物學試驗參照樣品的選擇和定性 |
Biological evaluation of medical devices - Part 8: Selection and qualification of reference materials for biological tests (ISO 10993-8:2000) |
| EN ISO 10993-9-1999 |
醫療器械的生物學評價第9部分：潛在降解產物的定性與定量總則 |
Biological evaluation of medical devices - Part 9: Framework for identification and quantification of potential degradation products (ISO 10993-9:1999) |
| EN ISO 11058-1999 |
土工布及相關產品無負載下垂直透水性的測定 |
Geotextiles and geotextile-related products - Determination of water permeability characteristics normal to the plane, without load (ISO 11058:1999) |
| EN ISO 11064-1-2000 |
控制中心的人類工效學設計第1部分：控制中心設計的原則 |
Ergonomic design of control centres - Part 1: Principles for the design of control centres (ISO 11064-1:2000) |
| EN ISO 11064-2-2000 |
控制中心的人類工效學設計第2部分：控制序列排列的原則 |
Ergonomic design of control centres - Part 2: Principles for the arrangement of control suite (ISO 11064-2:2000) |
| EN ISO 11064-3-1999 |
控制中心的人類工效學設計第3部分：控制室布置 |
Ergonomic design of control centres - Part 3: Control room layout (ISO 11064-3:1999) |
| EN ISO 11064-4-2004 |
控制中心的人類工效學設計.第4部分:工作站的布置和尺寸 |
|
| EN ISO 1107-2003 |
魚網 網 基本術語和定義 |
Fishing nets - Netting - Basic terms and definitions (ISO 1107:2003) |
| EN ISO 11070-1999 |
一次性無菌血管內導管導引器 |
Sterile single-use intravascular catheter introducers (ISO 11070:1998) |
| EN ISO 11091-1999 |
建筑工程制圖園林制圖實用規程 |
Construction drawings - Landscape drawing practice (ISO 11091:1994) |
| EN ISO 1110-1997 |
塑料聚先胺試樣的加速狀態調節 |
Plastics - Polyamides - Accelerated conditioning of test specimens (ISO 1110:1995) |
| EN ISO 11102-1-1997 |
往復式內燃機手柄起動裝置第1部分：安全要求和試驗 |
Reciprocating internal combustion engines - Handle starting equipment - Part 1: Safety requirements and tests (ISO 11102-1:1997) |
| EN ISO 11102-2-1997 |
往復式內燃機手柄起動裝置第2部分：脫開角試驗方法 |
Reciprocating internal combustion engines - Handle starting equipment - Part 2: Method of testing the angle of disengagement (ISO 11102-2:1997) |
| EN ISO 11105-1997 |
小艇汽油機和/或汽油柜艙室的通風 |
Small craft - Ventilation of petrol engine and/or petrol tank compartments (ISO 11105:1997) |
| EN ISO 11111-1995 |
紡織機械的安全要求 |
Safety requirements for textile machinery (ISO 11111:1995) |
| EN ISO 11114-2-2000 |
可運輸氣瓶氣瓶和瓶閥材料與盛裝氣體的相容性第2部分：非金屬材料 |
Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2000) |
| EN ISO 11114-3-1997 |
可運輸氣瓶氣瓶和瓶閥材料與盛裝氣體的相容性第3部分：氧環境中自燃試驗 |
Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 3: Autogenous ignition test in oxygen atmosphere (ISO 11114-3:1997) |
| EN ISO 11116-1-1999 |
氣瓶氣瓶與瓶閥連接用17E錐螺紋第1部分：規范 |
Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 1: Specifications (ISO 11116-1:1999) |
| EN ISO 11116-2-1999 |
氣瓶氣瓶與瓶閥連接用17E錐螺紋第2部分：檢驗量規 |
Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 2: Inspection gauges (ISO 11116-2:1999) |
| EN ISO 11120-1999 |
氣瓶150L至3000L水容量的可重復充裝無縫綱管氣瓶設計、結構和試驗 |
Gas cylinders - Refillable seamless steel tubes for compressed gas transport, of water capacity between 150 l and 3000 l - Design, construction and testing (ISO 11120:1999) |
| EN ISO 11124-1-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用金屬磨料的技術要求第1部分：一般介紹及分類 |
Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 1: General introduction and classification (ISO 11124-1:1993) |
| EN ISO 11124-2-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用金屬磨料的技術要求第2部分：冷硬鑄鐵丸 |
Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 2: Chilled-iron grit (ISO 11124-2:1993) |
| EN ISO 11124-3-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用金屬磨料的技術要求第3部分：高碳鑄鋼丸和砂 |
Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 3: High-carbon cast-steel shot and grit (ISO 11124-3:1993) |
| EN ISO 11124-4-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用金屬磨料的技術要求第4部分：低碳鑄鋼丸 |
Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 4: Low-carbon cast-steel shot (ISO 11124-4:1993) |
| EN ISO 11125-1-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用金屬磨料的試驗方法第1部分：抽樣 |
Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 1: Sampling (ISO 11125-1:1993) |
| EN ISO 11125-2-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用金屬磨料的試驗方法第2部分：顆粒尺寸分布的測定 |
Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 2: Determination of particle size distribution (ISO 11125-2:1993) |
| EN ISO 11125-3-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用金屬磨料的試驗方法第3部分：硬度測定 |
Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 3: Determination of hardness (ISO 11125-3:1993) |
| EN ISO 11125-4-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用金屬磨料的試驗方法第4部分：表觀密度測定 |
Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 4: Determination of apparent density (ISO 11125-4:1993) |
| EN ISO 11125-5-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用金屬磨料的試驗方法第5部分：缺陷顆粒的百分比和微結構的測定 |
Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 5: Determination of percentage defective particles and of microstructure (ISO 11125-5:1993) |
| EN ISO 11125-6-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用金屬磨料的試驗方法第6部分：外來雜質測定 |
Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 6: Determination of foreign matter (ISO 11125-6:1993) |
| EN ISO 11125-7-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用金屬磨料的試驗方法第7部分：含水量測定 |
Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 7: Determination of moisture (ISO 11125-7:1993) |
| EN ISO 11126-1-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的技術要求第1部分：總體介紹和分類(包括技術勘誤1 |
Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 1: General introduction and classification (ISO 11126-1:1993, including Technical Corrigenda 1:1997 and 2: |
| EN ISO 11126-3-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的技術要求第3部分：銅精煉渣 |
Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 3: Copper refinery slag (ISO 11126-3:1993) |
| EN ISO 11126-4-1998 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的技術要求第4部分：煤爐渣 |
Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 4: Coal furnace slag (ISO 11126-4:1993) |
| EN ISO 11126-5-1998 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的技術要求第5部分：鎳精煉渣 |
Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 5: Nickel refinery slag (ISO 11126-5:1993) |
| EN ISO 11126-6-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的技術要求第6部分：煉鐵爐渣 |
Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 6: Iron furnace slag (ISO 11126-6:1993) |
| EN ISO 11126-7-1999 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的技術要求第7部分：熔融氧化鋁 |
Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 7: Fused aluminium oxide (ISO 11126-7:1995) |
| EN ISO 11126-8-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的技術要求第8部分：橄欖石砂 |
Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 8: Olivine sand (ISO 11126-8:1993) |
| EN ISO 11127-1-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的試驗方法第1部分：抽樣 |
Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 1: Sampling (ISO 11127-1:1993) |
| EN ISO 11127-2-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的試驗方法第2部分：顆粒尺寸分布的測定 |
Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 2: Determination of particle size distribution (ISO 11127-2:1993) |
| EN ISO 11127-3-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的試驗方法第3部分：表觀密度測定 |
Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 3: Determination of apparent density (ISO 11127-3:1993) |
| EN ISO 11127-4-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的試驗方法第4部分：通過玻璃載片試驗評定硬度 |
Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 4: Assessment of hardness by a glass slide test (ISO 11127-4:1993) |
| EN ISO 11127-5-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的試驗方法第5部分：含水量測定 |
Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 5: Determination of moisture (ISO 11127-5:1993) |
| EN ISO 11127-6-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的試驗方法第6部分：通過測量電導率測定水溶性雜質 |
Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 6: Determination of water-soluble contaminants by conductivity measurement (ISO 11127-6:1993) |
| EN ISO 11127-7-1997 |
涂裝油漆和有關產品前鋼材預處理噴射清理用非金屬磨料的試驗方法第7部分：水溶性氯化物的測定 |
Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 7: Determination of water soluble chlorides (ISO 11127-7:1993) |
| EN ISO 11130-1999 |
金屬與合金的腐蝕鹽溶液中的交替浸入試驗 |
Corrosion of metals and alloys - Alternate immersion test in salt solution (ISO 11130:1999) |
| EN ISO 11143-1999 |
牙科設備汞齊合金分離器 |
Dental equipment - Amalgam separators (ISO 11143:1999) |
| EN ISO 11144-1996 |
牙科設備供水及排水管接頭 |
Dental equipment - Connections for supply and waste lines (ISO 11144:1995) |
| EN ISO 11145-2001 |
光學和光學儀器激光和激光設備詞匯和符號 |
Optics and optical instruments - Lasers and laser-related equipment - Vocabulary and symbols (ISO 11145:2001) |
| EN ISO 11146-1999 |
激光和激光設備激光束參數的試驗方法束寬、發散角和束擴散因子 |
Lasers and laser-related equipment - Test methods for laser beam parameters - Beam widths, divergence angle and beam propagation factor (ISO 11146:1999) |
| EN ISO 11149-1997 |
光學和光學儀器激光和激光設備非電信激光設備用光纖連接器 |
Optics and optical instruments - Lasers and laser-related equipment - Fibre optic connectors for non-telecommunication laser applications (ISO 11149:1997) |
| EN ISO 11151-1-2000 |
激光和激光設備標準光學件第1部分：紫外線、可見和近紅外光譜范圍用件 |
Lasers and laser-related equipment - Standard optical components - Part 1: Components for the UV, visible and near-infrared spectral range (ISO 11151-1:2000) |
| EN ISO 11151-2-2000 |
激光和激光設備標準光學件第2部分：紅外光譜范圍用件 |
Lasers and laser-related equipment - Standard optical components - Part 2: Components for the infrared spectral range (ISO 11151-2:2000) |
| EN ISO 1119-2002 |
產品幾何量技術規范(GPS)錐度和錐度角系列 |
Geometrical Product Specifications (GPS) - Series of conical tapers and taper angles (ISO 1119:1998) |
| EN ISO 11196-1997 |
麻醉氣體監視器(包括技術勘誤1) |
Aneasthetic gas monitors (ISO 11196:1995 including Technical Corrigendum 1:1997) |
| EN ISO 11197-2004 |
醫療供電設備 |
|
| EN ISO 11199-1-1999 |
雙臂操作的助步器要求和試驗方法第1部分：步行支架 |
Walking aids manipulated by both arms - Requirements and test methods - Part 1: Walking frames (ISO 11199-1:1999) |
| EN ISO 11199-2-1999 |
雙臂操作的助步器要求和試驗方法第2部分：滾動器 |
Walking aids manipulated by both arms - Requirements and test methods - Part 2: Rollators (ISO 11199-2:1999) |
| EN ISO 1120-2002 |
輸送帶機械接頭的強度測定靜態試驗法 |
Conveyor belts - Determination of strength of mechanical fastenings - Static test method (ISO 1120:2002) |
| EN ISO 11203-1995 |
聲學機器和設備發射的噪聲從聲功率級測定工作位置和其他指定位置發射聲壓級 |
Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995) |
| EN ISO 11210-1995 |
鉑合金首飾中含鉑量的測定氯鉑酸銨沉淀后重量法 |
Determination of platinum in platinum jewellery alloys - Gravimetric method after precipation of diammonium hexachloroplatinate (ISO 11210:1995) |
| EN ISO 11212-1-1997 |
淀粉和淀粉制品重金屬含量第1部分：用原子吸收光譜法測定砷含量 |
Starch and derived products - Heavy metals content - Part 1: Determination of arsenic content by atomic absorption spectrometry (ISO 11212-1:1997) |
| EN ISO 11212-2-1997 |
淀粉和淀粉制品重金屬含量第2部分：用原子吸收光譜法測定汞含量 |
Starch and derived products - Heavy metals content - Part 2: Determination of mercury content by atomic absorption spectrometry (ISO 11212-2:1997) |
| EN ISO 11212-3-1997 |
淀粉和淀粉制品重金屬含量第3部分：用電熱原子化原子吸收光譜法測定鉛含量 |
Starch and derived products - Heavy metals content - Part 3: Determination of lead content by atomic absorption spectrometry with electrothermal atomization (ISO 11212-3:1997) |
| EN ISO 11212-4-1997 |
淀粉和淀粉制品重金屬含量第4部分：用電熱原子化原子吸收光譜法測定鎘含量 |
Starch and derived products - Heavy metals content - Part 4: Determination of cadmium content by atomic absorption spectrometry with electrothermal atomization (ISO 11212-4:1997) |
| EN ISO 11213-1995 |
改良淀粉乙酰基含量的測定酶催化法 |
Modified starch - Determination of acetyl content - Enzymatic method (ISO 11213:1995) |
| EN ISO 11214-1996 |
改良淀粉氧化淀粉中羥基團含量的測定 |
Modified starch - Determination of carboxyl group content of oxidized starch (ISO 11214:1996) |
| EN ISO 11215-1998 |
改良淀粉乙酰二淀粉和已二酸酯中已二酸含量的測定氣相色譜法 |
Modified starch - Determination of adipic acid content of acetylated di-starch adipates - Gas-chromatographic method (ISO 11215:1998) |
| EN ISO 11216-1998 |
改良淀粉羧甲基淀粉中羧甲基團含量的測定 |
Modified starch - Determination of content of carboxymethyl groups in carboxymethyl starch (ISO 11216:1998) |
| EN ISO 11244-1999 |
牙科釬焊包埋料 |
Dental brazing investments (ISO 11244:1998) |
| EN ISO 11245-2000 |
牙齒修復磷酸鹽結合劑耐火模鑄材料 |
Dental restorations - Phosphate-bonded refractory die materials (ISO 11245:1999) |
| EN ISO 11246-1998 |
牙科硅酸乙脂結合劑鑄造包埋材料 |
Dental ethyl silicate bonded casting investments (ISO 11246:1996) |
| EN ISO 11248-1999 |
塑料熱固性模塑料溫升時短暫性能的評價 |
Plastics - Thermosetting moulding materials - Evaluation of short-term performance at elevated temperatures(ISO 11248:1993) |
| EN ISO 11254-1-2000 |
激光和激光設備光學表面激光導致?lián)p傷閾值的測定第1部分：1-on-1試驗 |
Lasers and laser-related equipment - Determination of laser-induced damage threshold of optical surfaces - Part 1: 1-on-1 test (ISO 11254-1:2000) |
| EN ISO 11254-2-2001 |
激光和激光設備光學表面激光導致?lián)p傷閾值的測定第2部分：S on 1試驗 |
Lasers and laser-related equipment - Determination of laser-induced damage threshold of optical surfaces - Part 2: S on 1 test (ISO 11254-2:2001) |
| EN ISO 1127-1996 |
不銹鋼管尺寸、公差和單位長度的公稱質量 |
Stainless steel tubes - Dimensions, tolerances and conventional masses per unit length |
| EN ISO 11290-1-1996 |
食品和動物飼料的微生物學單核細胞增生性利斯特氏菌檢測和計數的水平方法第1部分：檢測方法 |
Microbiology of food and animal feeding stuffs - Horizontal method for detection and enumeration of Listeria monocytogenes - Part 1: Detection method (ISO 11290-1:1996) |
| EN ISO 11290-1-2004 |
食品和動物飼料的微生物學.單核細胞增生性利斯特氏菌檢測和計數的水平方法.第1部分:檢測方法 |
|
| EN ISO 11290-1/prA1-2002 |
食品和動物飼料的微生物學單核細胞增生性利斯特氏菌檢測和計數的水平方法第1部分：檢測方法修改1：改 |
Microbiology of food and animal feeding stuffs - Horizontal method for detection and enumeration of Listeria monocytogenes - Part 1: Detection method; Amendment 1: Modification of the isolation media, of the haemolysis test and inclusion of precision |
| EN ISO 11290-2-1998 |
食品和動物飼料的微生物學單核細胞增生性利斯特氏菌檢測和計數的水平方法第2部分：計數方法 |
Microbiology of food and animal feeding stuffs - Horizontal method for the detection and enumeration of Listeria monocytogenes - Part 2: Enumeration method (ISO 11290-2:1998) |
| EN ISO 11290-2-2004 |
食品和動物飼料的微生物學.單核細胞增生性利斯特氏菌檢測和計數的水平方法.第2部分:計數方法 |
|
| EN ISO 11290-2/prA1-2002 |
食品和動物飼料的微生物學單核細胞增生性利斯特氏菌檢測和計數的水平方法第2部分：計數方法修改1：改 |
Microbiology of food and animal feeding stuffs - Horizontal method for the detection and enumeration of Listeria monocytogenes - Part 2: Enumeration method; Amendment 1: Modification of the isolation medium (ISO 11290-2:1998/DAM 1:2002) |
| EN ISO 11306-1998 |
金屬與合金的腐蝕對海水表面的金屬和合金的暴露和評估準則 |
Corrosion of metals and alloys - Guidelines for exposing and evaluating metals and alloys in surface sea water (ISO 11306:1998) |
| EN ISO 1133-1999 |
塑料 熱塑性塑料熔體質量流動速率(MFR)和熔體體積流動速率(MFR)的測定 |
Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:1997) |
| EN ISO 11334-1-1997 |
用胳膊操作的助步器要求和試驗方法第1部分：肘支撐器 |
Walking aids manipulated by one arm - Requirements and test methods - Part 1: Elbow crutches (ISO 11334-1:1994) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com